.gitignore

@@ -6,4 +6,3 @@ src_vipa-2.0.4.tar.gz
 /src_vipa-2.1.0.tar.gz
 /s390-tools-*.tar.bz2
 /s390-tools-*.tar.gz
-/s390-tools-*-rust-vendor.tar.xz

20-zipl-kernel.install

@@ -54,25 +54,21 @@ EOF
 case "$COMMAND" in
     add)
         if [[ "${KERNEL_DIR}" != "/boot" ]]; then
-            # rename to match the name used in the pseudo-BLS snippet above
-            cp --remove-destination --preserve=timestamps -T "${KERNEL_IMAGE}" "/boot/vmlinuz-${KERNEL_VERSION}"
-            command -v restorecon &>/dev/null && \
-                restorecon -R "/boot/vmlinuz-${KERNEL_VERSION}"
-
             for i in \
+                "$KERNEL_IMAGE" \
                     "$KERNEL_DIR"/System.map \
                     "$KERNEL_DIR"/config \
                     "$KERNEL_DIR"/zImage.stub
             do
                 [[ -e "$i" ]] || continue
-                cp --preserve=timestamps -T "$i" "/boot/${i##*/}-${KERNEL_VERSION}"
+                cp -aT "$i" "/boot/${i##*/}-${KERNEL_VERSION}"
                 command -v restorecon &>/dev/null && \
                     restorecon -R "/boot/${i##*/}-${KERNEL_VERSION}"
             done
             # hmac is .vmlinuz-<version>.hmac so needs a special treatment
             i="$KERNEL_DIR/.${KERNEL_IMAGE##*/}.hmac"
             if [[ -e "$i" ]]; then
-                cp --preserve=timestamps "$i" "/boot/.${KERNEL_IMAGE##*/}-${KERNEL_VERSION}.hmac"
+                cp -a "$i" "/boot/.${KERNEL_IMAGE##*/}-${KERNEL_VERSION}.hmac"
                 command -v restorecon &>/dev/null && \
                     restorecon "/boot/.${KERNEL_IMAGE##*/}-${KERNEL_VERSION}.hmac"
             fi
@@ -92,10 +88,16 @@ case "$COMMAND" in
                 done
             fi
 
+            if ! [[ ${BOOT_OPTIONS[*]} ]]; then
+                echo "Could not determine the kernel command line parameters." >&2
+                echo "Please specify the kernel command line in /etc/kernel/cmdline!" >&2
+                exit 1
+            fi
+
             [[ -d "$BLS_DIR" ]] || mkdir -m 0700 -p "$BLS_DIR"
             BLS_TARGET="${BLS_DIR}/${MACHINE_ID}-${KERNEL_VERSION}.conf"
             if [[ -f "${KERNEL_DIR}/bls.conf" ]]; then
-                cp --preserve=timestamps -T "${KERNEL_DIR}/bls.conf" "${BLS_TARGET}" || exit $?
+                cp -aT "${KERNEL_DIR}/bls.conf" "${BLS_TARGET}" || exit $?
                 sed -i -e "s,^linux.*,linux /boot/vmlinuz-${KERNEL_VERSION},g" "${BLS_TARGET}"
                 sed -i -e "s,^initrd.*,initrd /boot/initramfs-${KERNEL_VERSION}.img,g" "${BLS_TARGET}"
                 sed -i -e "s#^options.*#options ${BOOT_OPTIONS[*]}#g" "${BLS_TARGET}"
@@ -116,7 +118,7 @@ case "$COMMAND" in
 
             if [ "x${MAKEDEBUG}" = "xyes" ]; then
                 BLS_DEBUG="$(echo ${BLS_TARGET} | sed -e "s/${KERNEL_VERSION}/${KERNEL_VERSION}~debug/")"
-                cp --preserve=timestamps -T  "${BLS_TARGET}" "${BLS_DEBUG}"
+                cp -aT  "${BLS_TARGET}" "${BLS_DEBUG}"
                 TITLE="$(grep '^title[ \t]' "${BLS_DEBUG}" | sed -e 's/^title[ \t]*//')"
 		VERSION="$(grep '^version[ \t]' "${BLS_DEBUG}" | sed -e 's/^version[ \t]*//')"
                 BLSID="$(grep '^id[ \t]' "${BLS_DEBUG}" | sed -e "s/${KERNEL_VERSION}/${KERNEL_VERSION}~debug/")"

52-zipl-rescue.install

@@ -29,6 +29,12 @@ case "$COMMAND" in
                 done
             fi
 
+            if ! [[ ${BOOT_OPTIONS[*]} ]]; then
+                echo "Could not determine the kernel command line parameters." >&2
+                echo "Please specify the kernel command line in /etc/kernel/cmdline!" >&2
+                exit 1
+            fi
+
             BLS_RESCUE="${BLS_DIR}/${MACHINE_ID}-0-rescue.conf"
             if [[ -f "${BLS_RESCUE}" ]] && grep -q '^options.*$kernelopts' "${BLS_RESCUE}"; then
                sed -i -e "s,^linux.*,linux /boot/vmlinuz-0-rescue-${MACHINE_ID},g" "${BLS_RESCUE}"

ccw.udev

@@ -1,4 +1,4 @@
-ACTION!="add|bind|change", GOTO="ccw_end"
+ACTION!="bind", GOTO="ccw_end"
 SUBSYSTEM!="ccw", GOTO="ccw_end"
 DRIVER=="ctcm|lcs|qeth", RUN+="ccw_init"
 LABEL="ccw_end"

rpminspect.yaml

@@ -1,8 +0,0 @@
----
-pathmigration:
-    excluded_paths:
-        - /lib/s390-tools
-
-badfuncs:
-    ignore:
-        - /usr/sbin/qethqoat

s390-tools-zipl-blscfg-rpm-nvr-sort.patch

@@ -1,234 +1,19 @@
-From b2daaa34776ba6afec879e362378f6f7563590a6 Mon Sep 17 00:00:00 2001
+diff -up s390-tools-2.9.0/zipl/src/Makefile.blscfg-rpm-nvr-sort s390-tools-2.9.0/zipl/src/Makefile
-From: =?UTF-8?q?Dan=20Hor=C3=A1k?= <dan@danny.cz>
+--- s390-tools-2.9.0/zipl/src/Makefile.blscfg-rpm-nvr-sort	2019-05-22 08:16:17.317273801 -0400
-Date: Mon, 20 Jun 2022 17:43:05 +0200
++++ s390-tools-2.9.0/zipl/src/Makefile	2019-05-22 08:18:02.947273801 -0400
-Subject: [PATCH 1/2] Revert "zipl/src: Implement sorting bls entries by
+@@ -7,7 +7,7 @@ ALL_CPPFLAGS += -I../include -I../boot \
- versions"
+ 	    -D_FILE_OFFSET_BITS=64 $(NO_PIE_CFLAGS)
-
+ ALL_LDFLAGS += -Wl,-z,noexecstack $(NO_PIE_LDFLAGS)
-This reverts commit a0dba6bfdb50ff373fa710ffe2a307cc0748f18b.
----
- zipl/src/scan.c | 139 ++----------------------------------------------
- 1 file changed, 3 insertions(+), 136 deletions(-)
-
-diff --git a/zipl/src/scan.c b/zipl/src/scan.c
-index 0cea1d4..9352f76 100644
---- a/zipl/src/scan.c
-+++ b/zipl/src/scan.c
-@@ -10,7 +10,6 @@
-  *
-  */
  
--static const char *VERSION_KEYWORD = "version";
+-libs = $(rootdir)/libutil/libutil.a
++libs = $(rootdir)/libutil/libutil.a -lrpmio -lrpm
  
- /* Need ISOC99 function isblank() in ctype.h */
+ objects = misc.o error.o scan.o job.o boot.o bootmap.o disk.o \
- #ifndef __USE_ISOC99
+ 	  install.o zipl.o $(rootdir)/zipl/boot/data.o
-@@ -646,7 +645,7 @@ scan_file(const char* filename, struct scan_token** token)
+diff -up s390-tools-2.9.0/zipl/src/scan.c.blscfg-rpm-nvr-sort s390-tools-2.9.0/zipl/src/scan.c
- 
+--- s390-tools-2.9.0/zipl/src/scan.c.blscfg-rpm-nvr-sort	2019-05-21 09:13:36.000000000 -0400
- 
++++ s390-tools-2.9.0/zipl/src/scan.c	2019-05-22 08:16:17.317273801 -0400
- static int
+@@ -33,6 +33,8 @@
--bls_filter_by_names(const struct dirent *ent)
-+bls_filter(const struct dirent *ent)
- {
- 	int offset = strlen(ent->d_name) - strlen(".conf");
- 
-@@ -656,111 +655,13 @@ bls_filter_by_names(const struct dirent *ent)
- 	return strncmp(ent->d_name + offset, ".conf", strlen(".conf")) == 0;
- }
- 
--struct version {
--	char *line; /* pointer to a line with version keyword */
--	int offset; /* offset of version value in the line */
--};
--
--/*
-- * Locate version in bls file represented by ENT
-- */
--static void get_version(const struct dirent *ent, struct version *v)
--{
--	char *line = NULL;
--	size_t len = 0;
--	char *d_name;
--	FILE *stream;
--	ssize_t read;
--
--	memset(v, 0, sizeof(*v));
--	d_name = misc_make_path((char *)blsdir, (char *)ent->d_name);
--	if (!d_name)
--		return;
--
--	stream = fopen(d_name, "r");
--	free(d_name);
--	if (!stream)
--		return;
--
--	while ((read = getline(&line, &len, stream)) != -1) {
--		if (line[read - 1] == '\n') {
--			line[read - 1] = '\0';
--			read--;
--		}
--		if ((size_t)read <= strlen(VERSION_KEYWORD) + 1)
--			continue;
--		if (strcmp(VERSION_KEYWORD, line) > 0)
--			continue;
--		if (!isblank(line[strlen(VERSION_KEYWORD)]))
--			continue;
--		/* skip blanks */
--		v->offset = strlen(VERSION_KEYWORD) + 1;
--		while (v->offset < read - 1 && isblank(line[v->offset]))
--			v->offset++;
--		if (isblank(line[v->offset]))
--			/*
--			 * all characters after the keyword
--			 * are blanks. Invalid version
--			 */
--			continue;
--		v->line = line;
--		fclose(stream);
--		return;
--	}
--	free(line);
--	fclose(stream);
--}
--
--static void put_version(struct version *v)
--{
--	free(v->line);
--}
--
--/**
-- * Check version in bls file represented by ENT.
-- * Return 1 if version is valid. Otherwise return 0
-- */
--static int bls_filter_by_versions(const struct dirent *ent)
--{
--	struct version v;
--
--	if (bls_filter_by_names(ent) == 0)
--		return 0;
--
--	get_version(ent, &v);
--	if (v.line) {
--		put_version(&v);
--		return 1;
--	}
--	return 0;
--}
--
- 
- static int
--bls_sort_by_names(const struct dirent **ent_a, const struct dirent **ent_b)
-+bls_sort(const struct dirent **ent_a, const struct dirent **ent_b)
- {
- 	return strverscmp((*ent_a)->d_name, (*ent_b)->d_name);
- }
- 
--static int
--bls_sort_by_versions(const struct dirent **ent_a, const struct dirent **ent_b)
--{
--	struct version v1, v2;
--	int ret;
--
--	get_version(*ent_a, &v1);
--	get_version(*ent_b, &v2);
--	/*
--	 * Both versions are valid.
--	 * It is guaranteed by bls_filter_by_versions()
--	 */
--	ret = strverscmp(v1.line + v1.offset, v2.line + v2.offset);
--
--	put_version(&v1);
--	put_version(&v2);
--
--	return ret;
--}
- 
- static int
- scan_append_section_heading(struct scan_token* scan, int* index, char* name);
-@@ -1110,40 +1011,6 @@ scan_count_target_keywords(char* keyword[])
- 	return num;
- }
- 
--static int bls_scandir(struct dirent ***bls_entries)
--{
--	struct dirent **entries1;
--	struct dirent **entries2;
--	int n1, n2;
--
--	/* arrange by names */
--	n1 = scandir(blsdir, &entries1,
--		     bls_filter_by_names, bls_sort_by_names);
--	if (n1 <= 0)
--		return n1;
--	/* arrange by versions */
--	n2 = scandir(blsdir, &entries2,
--		     bls_filter_by_versions, bls_sort_by_versions);
--
--	if (n2 <= 0 || n2 < n1) {
--		/*
--		 * failed to sort by versions,
--		 * fall back to sorting by filenames
--		 */
--		*bls_entries = entries1;
--		while (n2--)
--			free(entries2[n2]);
--		free(entries2);
--		return n1;
--	}
--	/* use arrangement by versions */
--	*bls_entries = entries2;
--	while (n1--)
--		free(entries1[n1]);
--	free(entries1);
--	return n2;
--}
--
- int
- scan_check_target_data(char* keyword[], int* line)
- {
-@@ -1464,7 +1331,7 @@ int scan_bls(struct scan_token **token, int scan_size)
- 	if (!(stat(blsdir, &sb) == 0 && S_ISDIR(sb.st_mode)))
- 		return 0;
- 
--	n = bls_scandir(&bls_entries);
-+	n = scandir(blsdir, &bls_entries, bls_filter, bls_sort);
- 	if (n <= 0)
- 		return n;
- 
--- 
-2.39.2
-
-
-From 692e70bcfc32a05e30146bd7077c41e0eaceff03 Mon Sep 17 00:00:00 2001
-From: Peter Jones <pjones@redhat.com>
-Date: Mon, 20 Jun 2022 17:46:59 +0200
-Subject: [PATCH 2/2] blscfg: sort like rpm nvr, not like a single version
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Peter Jones <pjones@redhat.com>
-Signed-off-by: Dan Horák <dan@danny.cz>
----
- zipl/src/Makefile |  1 +
- zipl/src/scan.c   | 96 ++++++++++++++++++++++++++++++++++++++++++++++-
- 2 files changed, 95 insertions(+), 2 deletions(-)
-
-diff --git a/zipl/src/Makefile b/zipl/src/Makefile
-index cab5655..7ec215d 100644
---- a/zipl/src/Makefile
-+++ b/zipl/src/Makefile
-@@ -9,6 +9,7 @@ ALL_LDFLAGS += -Wl,-z,noexecstack $(NO_PIE_LDFLAGS)
- 
- libs =  $(rootdir)/libutil/libutil.a \
- 	$(rootdir)/libvtoc/libvtoc.a \
-+	-lrpmio -lrpm
- 
- objects = misc.o error.o scan.o job.o boot.o bootmap.o fs-map.o disk.o \
- 	  bootmap_header.o envblk.o install.o zipl.o
-diff --git a/zipl/src/scan.c b/zipl/src/scan.c
-index 9352f76..3327e2d 100644
---- a/zipl/src/scan.c
-+++ b/zipl/src/scan.c
-@@ -35,6 +35,8 @@
  
  #include "lib/util_base.h"
  
@@ -237,7 +22,7 @@ index 9352f76..3327e2d 100644
  #include "boot.h"
  #include "error.h"
  #include "misc.h"
-@@ -655,13 +657,103 @@ bls_filter(const struct dirent *ent)
+@@ -653,13 +655,103 @@ bls_filter(const struct dirent *ent)
  	return strncmp(ent->d_name + offset, ".conf", strlen(".conf")) == 0;
  }
  
@@ -343,6 +128,3 @@ index 9352f76..3327e2d 100644
  
  static int
  scan_append_section_heading(struct scan_token* scan, int* index, char* name);
--- 
-2.39.2
-

s390-tools-zipl-invert-script-options.patch

@@ -61,10 +61,10 @@ index 871935c783f..d8d5eca5867 100755
  	    ;;
  	--)
  	    shift
-diff --git a/scripts/zipl-switch-to-blscfg.8 b/scripts/zipl-switch-to-blscfg.8
+diff --git a/scripts/zipl-switch-to-blscfg.1 b/scripts/zipl-switch-to-blscfg.1
 index 6bd14d00d14..71b904ffd1c 100644
---- a/scripts/zipl-switch-to-blscfg.8
+--- a/scripts/zipl-switch-to-blscfg.1
-+++ b/scripts/zipl-switch-to-blscfg.8
++++ b/scripts/zipl-switch-to-blscfg.1
 @@ -37,9 +37,9 @@ The DIRECTORY where the BLS fragments will be generated. The directory is create
  The FILE used for zipl configuration file, defaults to /etc/zipl.conf.
  

s390utils.spec

@@ -1,30 +1,17 @@
 # secure boot support is for RHEL only
 %if 0%{?rhel} >= 8
-%bcond_without signzipl
+%global signzipl 1
-%else
-%bcond_with signzipl
-%endif
-
-%if 0%{?fedora}
-%bcond_without pandoc
-%else
-%bcond_with pandoc
 %endif
 
 Name:           s390utils
 Summary:        Utilities and daemons for IBM z Systems
-Version:        2.31.0
+Version:        2.17.0
 Release:        2%{?dist}
 Epoch:          2
-# MIT covers nearly all the files, except init files
+License:        MIT
-License:        MIT AND LGPL-2.1-or-later
+ExclusiveArch:  s390 s390x
 URL:            https://github.com/ibm-s390-linux/s390-tools
 Source0:        https://github.com/ibm-s390-linux/s390-tools/archive/v%{version}.tar.gz#/s390-tools-%{version}.tar.gz
-# To create the vendor tarball:
-#   tar xf s390-tools-%%{version}.tar.gz ; pushd s390-tools-%%{version}/rust ; \
-#   rm -f Cargo.lock && cargo vendor && \
-#   tar Jvcf ../../s390-tools-%%{version}-rust-vendor.tar.xz vendor/ ; popd
-Source1:        s390-tools-%{version}-rust-vendor.tar.xz
 Source5:        https://fedorapeople.org/cgit/sharkcz/public_git/utils.git/tree/zfcpconf.sh
 Source7:        https://fedorapeople.org/cgit/sharkcz/public_git/utils.git/tree/zfcp.udev
 Source12:       https://fedorapeople.org/cgit/sharkcz/public_git/utils.git/tree/dasd.udev
@@ -38,7 +25,7 @@ Source23:       20-zipl-kernel.install
 Source24:       52-zipl-rescue.install
 Source25:       91-zipl.install
 
-%if %{with signzipl}
+%if 0%{?signzipl}
 %define pesign_name redhatsecureboot302
 %endif
 
@@ -46,19 +33,6 @@ Source25:       91-zipl.install
 Patch0:         s390-tools-zipl-invert-script-options.patch
 Patch1:         s390-tools-zipl-blscfg-rpm-nvr-sort.patch
 
-# upstream fixes/updates
-#Patch100:       s390utils-%%{version}-fedora.patch
-
-# https://fedoraproject.org/wiki/Changes/EncourageI686LeafRemoval
-ExcludeArch:    %{ix86}
-
-# Add Provides for upstream name
-Provides:       s390-tools = %{epoch}:%{version}-%{release}
-
-%ifarch s390x
-#
-# s390x/native package structure
-#
 Requires:       s390utils-core = %{epoch}:%{version}-%{release}
 Requires:       s390utils-base = %{epoch}:%{version}-%{release}
 Requires:       s390utils-osasnmpd = %{epoch}:%{version}-%{release}
@@ -66,48 +40,9 @@ Requires:       s390utils-cpuplugd = %{epoch}:%{version}-%{release}
 Requires:       s390utils-mon_statd = %{epoch}:%{version}-%{release}
 Requires:       s390utils-iucvterm = %{epoch}:%{version}-%{release}
 Requires:       s390utils-ziomon = %{epoch}:%{version}-%{release}
-%else
-#
-# multiarch package structure
-#
-Requires:       s390utils-se-data = %{epoch}:%{version}-%{release}
-%endif
 
 BuildRequires:  make
 BuildRequires:  gcc-c++
-BuildRequires:  glib2-devel
-%if 0%{?rhel}
-BuildRequires:  libcurl-devel
-BuildRequires:  openssl-devel
-BuildRequires:  rust-toolset
-%else
-BuildRequires:  crate(anstream)
-BuildRequires:  crate(anstyle-query)
-BuildRequires:  crate(anyhow)
-BuildRequires:  crate(byteorder)
-BuildRequires:  crate(cfg-if)
-BuildRequires:  crate(clap)
-BuildRequires:  crate(clap_complete)
-BuildRequires:  crate(clap_derive)
-BuildRequires:  crate(colorchoice)
-BuildRequires:  crate(curl)
-BuildRequires:  crate(is-terminal)
-BuildRequires:  crate(lazy_static)
-BuildRequires:  crate(libc)
-BuildRequires:  crate(log)
-BuildRequires:  crate(mockito)
-BuildRequires:  crate(openssl)
-BuildRequires:  crate(openssl-probe)
-BuildRequires:  crate(serde)
-BuildRequires:  crate(serde_derive)
-BuildRequires:  crate(serde_test)
-BuildRequires:  crate(serde_yaml)
-BuildRequires:  crate(strsim)
-BuildRequires:  crate(terminal_size)
-BuildRequires:  crate(thiserror)
-BuildRequires:  crate(zerocopy)
-BuildRequires:  rust-packaging
-%endif
 
 %description
 This is a meta package for installing the default s390-tools sub packages.
@@ -118,24 +53,19 @@ The s390utils packages contain a set of user space utilities that should to
 be used together with the zSeries (s390) Linux kernel and device drivers.
 
 %prep
-%autosetup -n s390-tools-%{version} -p1
+%setup -q -n s390-tools-%{version}
+
+# Fedora/RHEL changes
+%patch0 -p1 -b .zipl-invert-script-options
+%patch1 -p1 -b .blscfg-rpm-nvr-sort
+
+# remove --strip from install
+find . -name Makefile | xargs sed -i 's/$(INSTALL) -s/$(INSTALL)/g'
 
-%if 0%{?rhel}
-pushd rust
-%cargo_prep -V 1
-popd
-%else
-%cargo_prep
-%endif
-rm ./rust/Cargo.lock
 
 %build
 make \
-        CFLAGS="%{build_cflags}" CXXFLAGS="%{build_cxxflags}" LDFLAGS="%{build_ldflags}" \
+        CFLAGS="%{build_cflags}" CXXFLAGS="%{build_cflags}" LDFLAGS="%{build_ldflags}" \
-        HAVE_DRACUT=1 \
-%if %{with pandoc}
-        ENABLE_DOC=1 \
-%endif
         NO_PIE_LDFLAGS="" \
         BINDIR=/usr/sbin \
         DISTRELEASE=%{release} \
@@ -145,21 +75,14 @@ make \
 %install
 make install \
         HAVE_DRACUT=1 \
-%if %{with pandoc}
-        ENABLE_DOC=1 \
-%endif
         DESTDIR=%{buildroot} \
         BINDIR=/usr/sbin \
         SYSTEMDSYSTEMUNITDIR=%{_unitdir} \
         DISTRELEASE=%{release} \
         V=1
 
-%ifarch s390x
-#
-# s390x/native specific %%install section
-#
 # sign the stage3 bootloader
-%if %{with signzipl}
+%if 0%{?signzipl}
 if [ -x /usr/bin/rpm-sign ]; then
     pushd %{buildroot}/lib/s390-tools/
         rpm-sign --key "%{pesign_name}" --lkmsign stage3.bin --output stage3.signed
@@ -217,61 +140,17 @@ install -p -m 644 %{SOURCE17} %{buildroot}%{_udevrulesdir}/81-ccw.rules
 
 # zipl.conf to be ghosted
 touch %{buildroot}%{_sysconfdir}/zipl.conf
-%endif
 
-%ifarch s390x
-#
-# s390x/native main %%files section
-#
-%files
-%doc README.md
-
-%else
-#
-# multiarch %%files section
-#
 
 %files
 %doc README.md
-%license LICENSE
-%{_bindir}/genprotimg
-%{_bindir}/pvapconfig
-%{_bindir}/pvattest
-%{_bindir}/pvextract-hdr
-%{_bindir}/pvsecret
-%{_mandir}/man1/genprotimg.1*
-%{_mandir}/man1/pvapconfig.1*
-%{_mandir}/man1/pvattest.1*
-%{_mandir}/man1/pvattest-create.1*
-%{_mandir}/man1/pvattest-perform.1*
-%{_mandir}/man1/pvattest-verify.1*
-%{_mandir}/man1/pvsecret-add.1*
-%{_mandir}/man1/pvsecret-create-association.1*
-%{_mandir}/man1/pvsecret-create-meta.1*
-%{_mandir}/man1/pvsecret-create.1*
-%{_mandir}/man1/pvsecret-list.1*
-%{_mandir}/man1/pvsecret-lock.1*
-%{_mandir}/man1/pvsecret-verify.1*
-%{_mandir}/man1/pvsecret.1*
-%dir %{_datadir}/s390-tools
-%{_datadir}/s390-tools/genprotimg/
 
-#
-# enf of multi-arch section
-#
-%endif
-
-%ifarch s390x
-#
-# s390x specific sub-packages
-#
 #
 # ************************* s390-tools core package  *************************
 #
 %package core
 License:        MIT
 Summary:        S390 core tools
-Provides:       s390-tools-core = %{epoch}:%{version}-%{release}
 Requires:       coreutils
 %{?systemd_requires}
 # BRs are covered via the base package
@@ -293,7 +172,7 @@ This package provides minimal set of tools needed to system to boot.
 
 %files core
 %doc README.md zdev/src/chzdev_usage.txt
-%license LICENSE
+%doc LICENSE
 %{_sbindir}/chreipl
 %{_sbindir}/chzdev
 %{_sbindir}/cio_ignore
@@ -301,25 +180,17 @@ This package provides minimal set of tools needed to system to boot.
 %{_sbindir}/dasdinfo
 %{_sbindir}/fdasd
 %{_sbindir}/lszdev
-%{_sbindir}/vmcp
 %{_sbindir}/zipl
-%{_sbindir}/zipl-editenv
 %dir /lib/s390-tools
 /lib/s390-tools/{zipl,chreipl}_helper.*
 /lib/s390-tools/cpictl
 /lib/s390-tools/stage3.bin
-/lib/s390-tools/zdev_id
-/lib/s390-tools/zdev-from-dasd_mod.dasd
 /lib/s390-tools/zdev-root-update
-/lib/s390-tools/zdev-to-dasd_mod.dasd
-/lib/s390-tools/zdev-to-rd.znet
 /lib/s390-tools/zipl.conf
 %ghost %config(noreplace) %{_sysconfdir}/zipl.conf
-%config(noreplace) %{_sysconfdir}/ziplenv
 %{_unitdir}/cpi.service
 %config(noreplace) %{_sysconfdir}/sysconfig/cpi
 /usr/lib/dracut/modules.d/95zdev/
-/usr/lib/dracut/modules.d/95zdev-kdump/
 %{_mandir}/man5/zipl.conf.5*
 %{_mandir}/man8/chreipl.8*
 %{_mandir}/man8/chzdev.8*
@@ -328,9 +199,7 @@ This package provides minimal set of tools needed to system to boot.
 %{_mandir}/man8/dasdinfo.8*
 %{_mandir}/man8/fdasd.8*
 %{_mandir}/man8/lszdev.8*
-%{_mandir}/man8/vmcp.8*
 %{_mandir}/man8/zipl.8*
-%{_mandir}/man8/zipl-editenv.8*
 
 # Additional Fedora/RHEL specific stuff
 %ghost %config(noreplace) %{_sysconfdir}/dasd.conf
@@ -350,7 +219,6 @@ This package provides minimal set of tools needed to system to boot.
 %{_udevrulesdir}/59-dasd.rules
 %{_udevrulesdir}/60-readahead.rules
 %{_udevrulesdir}/81-ccw.rules
-%{_udevrulesdir}/81-dpm.rules
 %{_udevrulesdir}/90-cpi.rules
 %{_sysconfdir}/kernel/install.d/20-grubby.install
 %{_prefix}/lib/kernel/install.d/10-zfcpdump.install
@@ -364,16 +232,14 @@ This package provides minimal set of tools needed to system to boot.
 #
 
 %package base
-License:        MIT AND LGPL-2.1-or-later
+License:        MIT
 Summary:        S390 base tools
-Provides:       s390-tools-base = %{epoch}:%{version}-%{release}
 Requires:       gawk sed coreutils
 Requires:       sg3_utils
 Requires:       ethtool
 Requires:       tar
 Requires:       file
 Requires:       s390utils-core = %{epoch}:%{version}-%{release}
-Requires:       s390utils-se-data = %{epoch}:%{version}-%{release}
 %{?systemd_requires}
 BuildRequires:  perl-generators
 BuildRequires:  ncurses-devel
@@ -381,6 +247,7 @@ BuildRequires:  glibc-static
 BuildRequires:  cryptsetup-devel >= 2.0.3
 BuildRequires:  json-c-devel
 BuildRequires:  rpm-devel
+BuildRequires:  glib2-devel
 BuildRequires:  libxml2-devel
 
 
@@ -446,6 +313,11 @@ s390 base tools. This collection provides the following utilities:
    * tunedasd:
      Adjust tunable parameters on DASD devices.
 
+   * vmconvert:
+     Convert system dumps created by the z/VM VMDUMP command into dumps with
+     LKCD format. These LKCD dumps can then be analyzed with the dump analysis
+     tool lcrash.
+
    * vmcp:
      Allows Linux users to send commands to the z/VM control program (CP).
      The normal usage is to invoke vmcp with the command you want to
@@ -545,9 +417,8 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 %{_sbindir}/lscss
 %{_sbindir}/lsdasd
 %{_sbindir}/lshwc
-%{_sbindir}/lsluns
 %{_sbindir}/lsqeth
-%{_sbindir}/lspai
+%{_sbindir}/lsluns
 %{_sbindir}/lsreipl
 %{_sbindir}/lsscm
 %{_sbindir}/lsshut
@@ -555,17 +426,16 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 %{_sbindir}/lstape
 %{_sbindir}/lszcrypt
 %{_sbindir}/lszfcp
-%{_sbindir}/pai
 %{_sbindir}/qetharp
 %{_sbindir}/qethconf
 %{_sbindir}/qethqoat
 %{_sbindir}/scsi_logging_level
-%{_sbindir}/sclpdbf
 %{_sbindir}/start_hsnc.sh
 %{_sbindir}/tape390_crypt
 %{_sbindir}/tape390_display
 %{_sbindir}/ttyrun
 %{_sbindir}/tunedasd
+%{_sbindir}/vmcp
 %{_sbindir}/vmur
 %{_sbindir}/xcec-bridge
 %{_sbindir}/zcryptctl
@@ -577,23 +447,13 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 %{_sbindir}/zpcictl
 %{_bindir}/dump2tar
 %{_bindir}/genprotimg
-%{_bindir}/pvapconfig
 %{_bindir}/mk-s390image
-%{_bindir}/pvattest
+%{_bindir}/vmconvert
-%{_bindir}/pvextract-hdr
-%{_bindir}/pvsecret
 %{_bindir}/zkey
 %{_bindir}/zkey-cryptsetup
 %{_unitdir}/dumpconf.service
 %ghost %config(noreplace) %{_sysconfdir}/zipl.conf
 %config(noreplace) %{_sysconfdir}/sysconfig/dumpconf
-%{_sysconfdir}/mdevctl.d/*
-/usr/lib/dracut/modules.d/99ngdump/
-# own the mdevctl dirs until new release is available
-%dir /usr/lib/mdevctl
-%dir /usr/lib/mdevctl/scripts.d
-%dir /usr/lib/mdevctl/scripts.d/callouts
-/usr/lib/mdevctl/scripts.d/callouts/ap-check
 /lib/s390-tools/dumpconf
 /lib/s390-tools/lsznet.raw
 %dir /lib/s390-tools/zfcpdump
@@ -604,21 +464,13 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 %dir %{_libdir}/zkey
 %{_libdir}/zkey/zkey-ekmfweb.so
 %{_libdir}/zkey/zkey-kmip.so
+%{_mandir}/man1/dbginfo.sh.1*
 %{_mandir}/man1/dump2tar.1*
-%{_mandir}/man1/genprotimg.1*
+%{_mandir}/man1/lscpumf.1*
-%{_mandir}/man1/pvapconfig.1*
+%{_mandir}/man1/lshwc.1*
-%{_mandir}/man1/pvattest.1*
+%{_mandir}/man1/vmconvert.1*
-%{_mandir}/man1/pvattest-create.1*
+%{_mandir}/man1/zfcpdbf.1*
-%{_mandir}/man1/pvattest-perform.1*
+%{_mandir}/man1/zipl-switch-to-blscfg.1*
-%{_mandir}/man1/pvattest-verify.1*
-%{_mandir}/man1/pvsecret-add.1*
-%{_mandir}/man1/pvsecret-create-association.1*
-%{_mandir}/man1/pvsecret-create-meta.1*
-%{_mandir}/man1/pvsecret-create.1*
-%{_mandir}/man1/pvsecret-list.1*
-%{_mandir}/man1/pvsecret-lock.1*
-%{_mandir}/man1/pvsecret-verify.1*
-%{_mandir}/man1/pvsecret.1*
 %{_mandir}/man1/zkey.1*
 %{_mandir}/man1/zkey-cryptsetup.1*
 %{_mandir}/man1/zkey-ekmfweb.1*
@@ -632,18 +484,15 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 %{_mandir}/man8/chzcrypt.8*
 %{_mandir}/man8/dasdstat.8*
 %{_mandir}/man8/dasdview.8*
-%{_mandir}/man8/dbginfo.sh.8*
 %{_mandir}/man8/dumpconf.8*
+%{_mandir}/man8/genprotimg.8.*
 %{_mandir}/man8/hsavmcore.8*
 %{_mandir}/man8/hsci.8*
 %{_mandir}/man8/hyptop.8*
 %{_mandir}/man8/lschp.8*
-%{_mandir}/man8/lscpumf.8*
 %{_mandir}/man8/lscss.8*
 %{_mandir}/man8/lsdasd.8*
-%{_mandir}/man8/lshwc.8*
 %{_mandir}/man8/lsluns.8*
-%{_mandir}/man8/lspai.8*
 %{_mandir}/man8/lsqeth.8*
 %{_mandir}/man8/lsreipl.8*
 %{_mandir}/man8/lsscm.8*
@@ -652,7 +501,6 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 %{_mandir}/man8/lstape.8*
 %{_mandir}/man8/lszcrypt.8*
 %{_mandir}/man8/lszfcp.8*
-%{_mandir}/man8/pai.8*
 %{_mandir}/man8/qetharp.8*
 %{_mandir}/man8/qethconf.8*
 %{_mandir}/man8/qethqoat.8*
@@ -660,15 +508,15 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 %{_mandir}/man8/tape390_display.8*
 %{_mandir}/man8/ttyrun.8*
 %{_mandir}/man8/tunedasd.8*
+%{_mandir}/man8/vmcp.8*
 %{_mandir}/man8/vmur.8*
 %{_mandir}/man8/zcryptctl.8*
 %{_mandir}/man8/zcryptstats.8*
-%{_mandir}/man8/zfcpdbf.8*
 %{_mandir}/man8/zgetdump.8*
-%{_mandir}/man8/zipl-switch-to-blscfg.8*
 %{_mandir}/man8/znetconf.8*
 %{_mandir}/man8/zpcictl.8*
 %dir %{_datadir}/s390-tools
+%{_datadir}/s390-tools/genprotimg/
 %{_datadir}/s390-tools/netboot/
 %dir %attr(0770,root,zkeyadm) %{_sysconfdir}/zkey
 %dir %attr(0770,root,zkeyadm) %{_sysconfdir}/zkey/kmip
@@ -680,25 +528,11 @@ getent group zkeyadm > /dev/null || groupadd -r zkeyadm
 # Additional Fedora/RHEL specific stuff
 /boot/tape0
 
-%package se-data
-License:        MIT
-Summary:        Data for Secure Execution
-Provides:       s390-tools-se-data = %{epoch}:%{version}-%{release}
-BuildArch:      noarch
-
-%description se-data
-%{summary}.
-
-%files se-data
-%dir %{_datadir}/s390-tools
-%{_datadir}/s390-tools/genprotimg/
-
 #
 # *********************** s390-tools osasnmpd package  ***********************
 #
 %package osasnmpd
 Summary:        SNMP sub-agent for OSA-Express cards
-Provides:       s390-tools-osasnmpd = %{epoch}:%{version}-%{release}
 Requires:       net-snmp
 Requires:       psmisc
 BuildRequires:  net-snmp-devel
@@ -718,7 +552,6 @@ ATM Ethernet LAN Emulation in QDIO mode.
 #
 %package mon_statd
 Summary:         Monitoring daemons for Linux in z/VM
-Provides:        s390-tools-mon_statd = %{epoch}:%{version}-%{release}
 Requires:        coreutils
 %{?systemd_requires}
 
@@ -758,7 +591,6 @@ Monitoring daemons for Linux in z/VM:
 #
 %package cpuplugd
 Summary:         Daemon that manages CPU and memory resources
-Provides:        s390-tools-cpuplugd = %{epoch}:%{version}-%{release}
 %{?systemd_requires}
 BuildRequires: systemd
 
@@ -788,7 +620,6 @@ memory can be increased or decreased exploiting the CMM1 feature.
 #
 %package ziomon
 Summary:        S390 ziomon tools
-Provides:       s390-tools-ziomon = %{epoch}:%{version}-%{release}
 Requires:       blktrace
 Requires:       coreutils
 Requires:       device-mapper-multipath
@@ -827,7 +658,6 @@ Tool set to collect data for zfcp performance analysis and report.
 #
 %package iucvterm
 Summary:        z/VM IUCV terminal applications
-Provides:       s390-tools-iucvterm = %{epoch}:%{version}-%{release}
 Requires(pre):  shadow-utils
 Requires(post): grep
 Requires(postun): grep
@@ -890,10 +720,8 @@ fi
 #
 %package cmsfs-fuse
 Summary:        CMS file system based on FUSE
-BuildRequires:  fuse3-devel
+BuildRequires:  fuse-devel
-Requires:       fuse3
+Requires:       fuse
-Provides:       s390-tools-cmsfs-fuse = %{epoch}:%{version}-%{release}
-Requires:       glibc-gconv-extra
 Obsoletes:      %{name}-cmsfs < 2:2.7.0-3
 
 %description cmsfs-fuse
@@ -910,10 +738,9 @@ This package contains the CMS file system based on FUSE.
 #
 %package zdsfs
 Summary:        z/OS data set access based on FUSE
-BuildRequires:  fuse3-devel
+BuildRequires:  fuse-devel
 BuildRequires:  libcurl-devel
-Requires:       fuse3
+Requires:       fuse
-Provides:       s390-tools-zdsfs = %{epoch}:%{version}-%{release}
 
 %description zdsfs
 This package contains the z/OS data set access based on FUSE.
@@ -927,9 +754,8 @@ This package contains the z/OS data set access based on FUSE.
 #
 %package hmcdrvfs
 Summary:       HMC drive file system based on FUSE
-BuildRequires: fuse3-devel
+BuildRequires: fuse-devel
-Requires:      fuse3
+Requires:      fuse
-Provides:      s390-tools-hmcdrvfs = %{epoch}:%{version}-%{release}
 
 %description hmcdrvfs
 This package contains a HMC drive file system based on FUSE and a tool
@@ -946,13 +772,11 @@ to list files and directories.
 #
 %package cpacfstatsd
 Summary:       Monitor and maintain CPACF activity counters
-Provides:      s390-tools-cpacfstatsd = %{epoch}:%{version}-%{release}
 Requires(post): systemd
 Requires(preun): systemd
 Requires(postun): systemd
 Requires(pre): shadow-utils
 BuildRequires: systemd
-BuildRequires: systemd-devel
 
 %description cpacfstatsd
 The cpacfstats tools provide a client/server application set to monitor
@@ -977,56 +801,12 @@ getent group cpacfstats >/dev/null || groupadd -r cpacfstats
 %{_mandir}/man8/cpacfstatsd.8*
 %{_unitdir}/cpacfstatsd.service
 
-#
-# *********************** chreipl-fcp-mpath package  ***********************
-#
-%package chreipl-fcp-mpath
-Summary:          Use multipath information for re-IPL path failover
-BuildRequires:    make
-BuildRequires:    bash
-BuildRequires:    coreutils
-%if %{with pandoc}
-BuildRequires:    pandoc
-%endif
-BuildRequires:    gawk
-BuildRequires:    gzip
-BuildRequires:    sed
-Provides:         s390-tools-chreipl-fcp-mpath = %{epoch}:%{version}-%{release}
-Requires:         bash
-Requires:         coreutils
-Requires:         util-linux
-Requires:         systemd-udev
-Requires:         device-mapper-multipath
-Requires:         dracut
-
-%description chreipl-fcp-mpath
-The chreipl-fcp-mpath toolset monitors udev events about paths to the re-IPL
-volume. If the currently configured FCP re-IPL path becomes unavailable, the
-toolset checks for operational paths to the same volume. If available, it
-reconfigures the FCP re-IPL settings to use an operational path.
-
-%files chreipl-fcp-mpath
-%doc chreipl-fcp-mpath/README.md
-%if %{with pandoc}
-%doc chreipl-fcp-mpath/README.html
-%endif
-%dir %{_prefix}/lib/chreipl-fcp-mpath/
-%{_prefix}/lib/chreipl-fcp-mpath/*
-%{_prefix}/lib/dracut/dracut.conf.d/70-chreipl-fcp-mpath.conf
-%{_prefix}/lib/udev/chreipl-fcp-mpath-is-ipl-tgt
-%{_prefix}/lib/udev/chreipl-fcp-mpath-is-ipl-vol
-%{_prefix}/lib/udev/chreipl-fcp-mpath-is-reipl-zfcp
-%{_prefix}/lib/udev/chreipl-fcp-mpath-record-volume-identifier
-%{_prefix}/lib/udev/chreipl-fcp-mpath-try-change-ipl-path
-%{_udevrulesdir}/70-chreipl-fcp-mpath.rules
-%{_mandir}/man7/chreipl-fcp-mpath.7*
-
 #
 # *********************** devel package  ***********************
 #
 %package devel
 Summary:        Development files
-Provides: s390-tools-devel = %{epoch}:%{version}-%{release}
+
 Requires: %{name}-base%{?_isa} = %{epoch}:%{version}-%{release}
 
 %description devel
@@ -1039,111 +819,8 @@ User-space development files for the s390/s390x architecture.
 %{_libdir}/libekmfweb.so
 %{_libdir}/libkmipclient.so
 
-#
-# end of s390x specific sub-packages
-#
-%endif
-
 
 %changelog
-* Fri Mar 08 2024 Neal Gompa <ngompa@fedoraproject.org> - 2:2.31.0-2
-- Add 's390-tools' Provides to all packages
-
-* Mon Feb 05 2024 Dan Horák <dan[at]danny.cz> - 2:2.31.0-1
-- rebased to 2.31.0 (rhbz#2262499)
-
-* Thu Jan 25 2024 Dan Horák <dan[at]danny.cz> - 2:2.30.0-2
-- add s390utils-se-data as a noarch subpackage with Secure Execution data files
-
-* Tue Jan 02 2024 Dan Horák <dan[at]danny.cz> - 2:2.30.0-1
-- rebased to 2.30.0 (rhbz#2252519)
-
-* Fri Dec 01 2023 Fabio Valentini <decathorpe@gmail.com> - 2:2.29.0-6
-- Rebuild for openssl crate >= v0.10.60 (RUSTSEC-2023-0044, RUSTSEC-2023-0072)
-
-* Fri Nov 10 2023 Dan Horák <dan[at]danny.cz> - 2:2.29.0-5
-- enable multi-arch build
-
-* Fri Nov 10 2023 Dan Horák <dan[at]danny.cz> - 2:2.29.0-4
-- fix upstream kernel installations
-
-* Mon Oct 23 2023 Yaakov Selkowitz <yselkowi@redhat.com> - 2:2.29.0-3
-- Use vendored dependencies in RHEL builds
-
-* Thu Aug 31 2023 Jakub Čajka <jcajka[at]redhat.com> - 2:2.29.0-2
-- enable rust based tools
-
-* Mon Aug 07 2023 Dan Horák <dan[at]danny.cz> - 2:2.29.0-1
-- rebased to 2.29.0
-
-* Sat Jul 22 2023 Fedora Release Engineering <releng@fedoraproject.org> - 2:2.28.0-2
-- Rebuilt for https://fedoraproject.org/wiki/Fedora_39_Mass_Rebuild
-
-* Tue Jul 11 2023 Dan Horák <dan[at]danny.cz> - 2:2.28.0-1
-- rebased to 2.28.0
-
-* Wed May 31 2023 Dan Horák <dan[at]danny.cz> - 2:2.27.0-1
-- rebased to 2.27.0
-
-* Fri May 19 2023 Petr Pisar <ppisar@redhat.com> - 2:2.26.0-2
-- Rebuild against rpm-4.19 (https://fedoraproject.org/wiki/Changes/RPM-4.19)
-
-* Fri Mar 03 2023 Dan Horák <dan[at]danny.cz> - 2:2.26.0-1
-- rebased to 2.26.0
-
-* Tue Jan 31 2023 Dan Horák <dan[at]danny.cz> - 2:2.25.0-4
-- add post GA fixes
-
-* Mon Jan 23 2023 Dan Horák <dan[at]danny.cz> - 2:2.25.0-3
-- revert the kernel install script change
-
-* Thu Jan 19 2023 Dan Horák <dan[at]danny.cz> - 2:2.25.0-2
-- update kernel install script to write /etc/kernel/cmdline
-
-* Fri Dec 09 2022 Dan Horák <dan[at]danny.cz> - 2:2.25.0-1
-- rebased to 2.25.0
-
-* Tue Nov 22 2022 Dan Horák <dan[at]danny.cz> - 2:2.24.0-2
-- update for Transparent DASD PPRC (Peer-to-Peer Remote Copy) handling
-
-* Thu Nov 10 2022 Dan Horák <dan[at]danny.cz> - 2:2.24.0-1
-- rebased to 2.24.0
-
-* Fri Aug 19 2022 Dan Horák <dan[at]danny.cz> - 2:2.23.0-1
-- rebased to 2.23.0
-
-* Sat Jul 23 2022 Fedora Release Engineering <releng@fedoraproject.org> - 2:2.22.0-2
-- Rebuilt for https://fedoraproject.org/wiki/Fedora_37_Mass_Rebuild
-
-* Mon Jun 20 2022 Dan Horák <dan[at]danny.cz> - 2:2.22.0-1
-- rebased to 2.22.0
-
-* Tue May 31 2022 Dan Horák <dan[at]danny.cz> - 2:2.21.0-2
-- do not fail on emtpy /proc/cmdline when installing kernel (#1899759)
-
-* Fri Apr 22 2022 Dan Horák <dan[at]danny.cz> - 2:2.21.0-1
-- rebased to 2.21.0
-
-* Mon Feb 07 2022 Dan Horák <dan[at]danny.cz> - 2:2.20.0-1
-- rebased to 2.20.0
-- switch to fuse3
-
-* Sat Jan 22 2022 Fedora Release Engineering <releng@fedoraproject.org> - 2:2.19.0-3
-- Rebuilt for https://fedoraproject.org/wiki/Fedora_36_Mass_Rebuild
-
-* Fri Nov 26 2021 Dan Horák <dan[at]danny.cz> - 2:2.19.0-2
-- update ccw udev rules
-
-* Fri Nov 12 2021 Dan Horák <dan[at]danny.cz> - 2:2.19.0-1
-- rebased to 2.19.0
-- cmsfs-fuse Requires glibc-gconv-extra (#2022652)
-
-* Wed Oct 20 2021 Dan Horák <dan[at]danny.cz> - 2:2.18.0-2
-- move vmcp to core (#1931287)
-
-* Tue Oct 05 2021 Dan Horák <dan[at]danny.cz> - 2:2.18.0-1
-- rebased to 2.18.0
-
 * Fri Jul 23 2021 Fedora Release Engineering <releng@fedoraproject.org> - 2:2.17.0-2
 - Rebuilt for https://fedoraproject.org/wiki/Fedora_35_Mass_Rebuild
 

sources

@@ -1,2 +1 @@
-SHA512 (s390-tools-2.31.0.tar.gz) = d05722dff760605baad92b25a7a9264b3c936ff851b87a02ab39604a74d02ae4e14632d9b3d83eb9cb82a14bfcbb0d40bb4797896051ed3dd36d7690abfb1c64
+SHA512 (s390-tools-2.17.0.tar.gz) = 57d1c90e2a270c380fd7b4ac8efdd301299d9e8671a7ff10747557135b27a06e8124a49f50b8729b450550ced61599f392606bcbe5e499c5bd488b9e207945da
-SHA512 (s390-tools-2.31.0-rust-vendor.tar.xz) = f9dc2887bb2502ba6f71ef7ea807380c322a46df8c65f0fc7993f3fb4eec4da120369d3e380dbcca9b6250307da0f6236a649504d542f44730e8009ace8ed450