kernel-ark/Documentation/aoe/aoe.txt
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

92 lines
3.3 KiB
Plaintext

The EtherDrive (R) HOWTO for users of 2.6 kernels is found at ...
http://www.coraid.com/support/linux/EtherDrive-2.6-HOWTO.html
It has many tips and hints!
CREATING DEVICE NODES
Users of udev should find the block device nodes created
automatically, but to create all the necessary device nodes, use the
udev configuration rules provided in udev.txt (in this directory).
There is a udev-install.sh script that shows how to install these
rules on your system.
If you are not using udev, two scripts are provided in
Documentation/aoe as examples of static device node creation for
using the aoe driver.
rm -rf /dev/etherd
sh Documentation/aoe/mkdevs.sh /dev/etherd
... or to make just one shelf's worth of block device nodes ...
sh Documentation/aoe/mkshelf.sh /dev/etherd 0
There is also an autoload script that shows how to edit
/etc/modprobe.conf to ensure that the aoe module is loaded when
necessary.
USING DEVICE NODES
"cat /dev/etherd/err" blocks, waiting for error diagnostic output,
like any retransmitted packets.
"echo eth2 eth4 > /dev/etherd/interfaces" tells the aoe driver to
limit ATA over Ethernet traffic to eth2 and eth4. AoE traffic from
untrusted networks should be ignored as a matter of security.
"echo > /dev/etherd/discover" tells the driver to find out what AoE
devices are available.
These character devices may disappear and be replaced by sysfs
counterparts, so distribution maintainers are encouraged to create
scripts that use these devices.
The block devices are named like this:
e{shelf}.{slot}
e{shelf}.{slot}p{part}
... so that "e0.2" is the third blade from the left (slot 2) in the
first shelf (shelf address zero). That's the whole disk. The first
partition on that disk would be "e0.2p1".
USING SYSFS
Each aoe block device in /sys/block has the extra attributes of
state, mac, and netif. The state attribute is "up" when the device
is ready for I/O and "down" if detected but unusable. The
"down,closewait" state shows that the device is still open and
cannot come up again until it has been closed.
The mac attribute is the ethernet address of the remote AoE device.
The netif attribute is the network interface on the localhost
through which we are communicating with the remote AoE device.
There is a script in this directory that formats this information
in a convenient way.
root@makki root# sh Documentation/aoe/status.sh
e10.0 eth3 up
e10.1 eth3 up
e10.2 eth3 up
e10.3 eth3 up
e10.4 eth3 up
e10.5 eth3 up
e10.6 eth3 up
e10.7 eth3 up
e10.8 eth3 up
e10.9 eth3 up
e4.0 eth1 up
e4.1 eth1 up
e4.2 eth1 up
e4.3 eth1 up
e4.4 eth1 up
e4.5 eth1 up
e4.6 eth1 up
e4.7 eth1 up
e4.8 eth1 up
e4.9 eth1 up