736b1c9c95
The two device tree files octeon_3xxx.dts and octeon_68xx.dts are trimmed by code in a subsequent patch to reflect the hardware actually present on the board. To this end several properties that are not part of the declared bindings are added to aid in trimming off unwanted nodes. Since the device tree and the code that trims it are bound into the kernel binary, these 'marker' properties never escape into the wild, and are purely an implementation detail of the kernel early boot process. This is done for backwards compatibility with existing boards (identified by a board type enumeration value by their bootloaders). New boards will always pass a device tree from the bootloader, the built-in trees are ignored in this case. Signed-off-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: devicetree-discuss@lists.ozlabs.org Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Rob Herring <rob.herring@calxeda.com> Cc: linux-kernel@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Patchwork: https://patchwork.linux-mips.org/patch/3937/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
572 lines
15 KiB
Plaintext
572 lines
15 KiB
Plaintext
/dts-v1/;
|
|
/*
|
|
* OCTEON 3XXX, 5XXX, 63XX device tree skeleton.
|
|
*
|
|
* This device tree is pruned and patched by early boot code before
|
|
* use. Because of this, it contains a super-set of the available
|
|
* devices and properties.
|
|
*/
|
|
/ {
|
|
compatible = "cavium,octeon-3860";
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
interrupt-parent = <&ciu>;
|
|
|
|
soc@0 {
|
|
compatible = "simple-bus";
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
ranges; /* Direct mapping */
|
|
|
|
ciu: interrupt-controller@1070000000000 {
|
|
compatible = "cavium,octeon-3860-ciu";
|
|
interrupt-controller;
|
|
/* Interrupts are specified by two parts:
|
|
* 1) Controller register (0 or 1)
|
|
* 2) Bit within the register (0..63)
|
|
*/
|
|
#interrupt-cells = <2>;
|
|
reg = <0x10700 0x00000000 0x0 0x7000>;
|
|
};
|
|
|
|
gpio: gpio-controller@1070000000800 {
|
|
#gpio-cells = <2>;
|
|
compatible = "cavium,octeon-3860-gpio";
|
|
reg = <0x10700 0x00000800 0x0 0x100>;
|
|
gpio-controller;
|
|
/* Interrupts are specified by two parts:
|
|
* 1) GPIO pin number (0..15)
|
|
* 2) Triggering (1 - edge rising
|
|
* 2 - edge falling
|
|
* 4 - level active high
|
|
* 8 - level active low)
|
|
*/
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
/* The GPIO pin connect to 16 consecutive CUI bits */
|
|
interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
|
|
<0 20>, <0 21>, <0 22>, <0 23>,
|
|
<0 24>, <0 25>, <0 26>, <0 27>,
|
|
<0 28>, <0 29>, <0 30>, <0 31>;
|
|
};
|
|
|
|
smi0: mdio@1180000001800 {
|
|
compatible = "cavium,octeon-3860-mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x11800 0x00001800 0x0 0x40>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
compatible = "marvell,88e1118";
|
|
marvell,reg-init =
|
|
/* Fix rx and tx clock transition timing */
|
|
<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
|
|
/* Adjust LED drive. */
|
|
<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
|
|
/* irq, blink-activity, blink-link */
|
|
<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
|
|
reg = <0>;
|
|
};
|
|
|
|
phy1: ethernet-phy@1 {
|
|
compatible = "marvell,88e1118";
|
|
marvell,reg-init =
|
|
/* Fix rx and tx clock transition timing */
|
|
<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
|
|
/* Adjust LED drive. */
|
|
<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
|
|
/* irq, blink-activity, blink-link */
|
|
<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
|
|
reg = <1>;
|
|
};
|
|
|
|
phy2: ethernet-phy@2 {
|
|
reg = <2>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
phy3: ethernet-phy@3 {
|
|
reg = <3>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
|
|
phy6: ethernet-phy@6 {
|
|
reg = <6>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
phy7: ethernet-phy@7 {
|
|
reg = <7>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
phy8: ethernet-phy@8 {
|
|
reg = <8>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
phy9: ethernet-phy@9 {
|
|
reg = <9>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
};
|
|
};
|
|
|
|
smi1: mdio@1180000001900 {
|
|
compatible = "cavium,octeon-3860-mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x11800 0x00001900 0x0 0x40>;
|
|
|
|
phy100: ethernet-phy@1 {
|
|
reg = <1>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
phy101: ethernet-phy@2 {
|
|
reg = <2>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
phy102: ethernet-phy@3 {
|
|
reg = <3>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
phy103: ethernet-phy@4 {
|
|
reg = <4>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
};
|
|
|
|
mix0: ethernet@1070000100000 {
|
|
compatible = "cavium,octeon-5750-mix";
|
|
reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
|
|
<0x11800 0xE0000000 0x0 0x300>, /* AGL */
|
|
<0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
|
|
<0x11800 0xE0002000 0x0 0x8>; /* AGL_PRT_CTL */
|
|
cell-index = <0>;
|
|
interrupts = <0 62>, <1 46>;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
mix1: ethernet@1070000100800 {
|
|
compatible = "cavium,octeon-5750-mix";
|
|
reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
|
|
<0x11800 0xE0000800 0x0 0x300>, /* AGL */
|
|
<0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */
|
|
<0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */
|
|
cell-index = <1>;
|
|
interrupts = <1 18>, < 1 46>;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy1>;
|
|
};
|
|
|
|
pip: pip@11800a0000000 {
|
|
compatible = "cavium,octeon-3860-pip";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x11800 0xa0000000 0x0 0x2000>;
|
|
|
|
interface@0 {
|
|
compatible = "cavium,octeon-3860-pip-interface";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0>; /* interface */
|
|
|
|
ethernet@0 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x0>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy2>;
|
|
cavium,alt-phy-handle = <&phy100>;
|
|
};
|
|
ethernet@1 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x1>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy3>;
|
|
cavium,alt-phy-handle = <&phy101>;
|
|
};
|
|
ethernet@2 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x2>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy4>;
|
|
cavium,alt-phy-handle = <&phy102>;
|
|
};
|
|
ethernet@3 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x3>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy5>;
|
|
cavium,alt-phy-handle = <&phy103>;
|
|
};
|
|
ethernet@4 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x4>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@5 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x5>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@6 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x6>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@7 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x7>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@8 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x8>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@9 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x9>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@a {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0xa>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@b {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0xb>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@c {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0xc>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@d {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0xd>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@e {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0xe>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
ethernet@f {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0xf>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
};
|
|
|
|
interface@1 {
|
|
compatible = "cavium,octeon-3860-pip-interface";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <1>; /* interface */
|
|
|
|
ethernet@0 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x0>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy6>;
|
|
};
|
|
ethernet@1 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x1>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy7>;
|
|
};
|
|
ethernet@2 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x2>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy8>;
|
|
};
|
|
ethernet@3 {
|
|
compatible = "cavium,octeon-3860-pip-port";
|
|
reg = <0x3>; /* Port */
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
phy-handle = <&phy9>;
|
|
};
|
|
};
|
|
};
|
|
|
|
twsi0: i2c@1180000001000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "cavium,octeon-3860-twsi";
|
|
reg = <0x11800 0x00001000 0x0 0x200>;
|
|
interrupts = <0 45>;
|
|
clock-frequency = <100000>;
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1337";
|
|
reg = <0x68>;
|
|
};
|
|
tmp@4c {
|
|
compatible = "ti,tmp421";
|
|
reg = <0x4c>;
|
|
};
|
|
};
|
|
|
|
twsi1: i2c@1180000001200 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "cavium,octeon-3860-twsi";
|
|
reg = <0x11800 0x00001200 0x0 0x200>;
|
|
interrupts = <0 59>;
|
|
clock-frequency = <100000>;
|
|
};
|
|
|
|
uart0: serial@1180000000800 {
|
|
compatible = "cavium,octeon-3860-uart","ns16550";
|
|
reg = <0x11800 0x00000800 0x0 0x400>;
|
|
clock-frequency = <0>;
|
|
current-speed = <115200>;
|
|
reg-shift = <3>;
|
|
interrupts = <0 34>;
|
|
};
|
|
|
|
uart1: serial@1180000000c00 {
|
|
compatible = "cavium,octeon-3860-uart","ns16550";
|
|
reg = <0x11800 0x00000c00 0x0 0x400>;
|
|
clock-frequency = <0>;
|
|
current-speed = <115200>;
|
|
reg-shift = <3>;
|
|
interrupts = <0 35>;
|
|
};
|
|
|
|
uart2: serial@1180000000400 {
|
|
compatible = "cavium,octeon-3860-uart","ns16550";
|
|
reg = <0x11800 0x00000400 0x0 0x400>;
|
|
clock-frequency = <0>;
|
|
current-speed = <115200>;
|
|
reg-shift = <3>;
|
|
interrupts = <1 16>;
|
|
};
|
|
|
|
bootbus: bootbus@1180000000000 {
|
|
compatible = "cavium,octeon-3860-bootbus";
|
|
reg = <0x11800 0x00000000 0x0 0x200>;
|
|
/* The chip select number and offset */
|
|
#address-cells = <2>;
|
|
/* The size of the chip select region */
|
|
#size-cells = <1>;
|
|
ranges = <0 0 0x0 0x1f400000 0xc00000>,
|
|
<1 0 0x10000 0x30000000 0>,
|
|
<2 0 0x10000 0x40000000 0>,
|
|
<3 0 0x10000 0x50000000 0>,
|
|
<4 0 0x0 0x1d020000 0x10000>,
|
|
<5 0 0x0 0x1d040000 0x10000>,
|
|
<6 0 0x0 0x1d050000 0x10000>,
|
|
<7 0 0x10000 0x90000000 0>;
|
|
|
|
cavium,cs-config@0 {
|
|
compatible = "cavium,octeon-3860-bootbus-config";
|
|
cavium,cs-index = <0>;
|
|
cavium,t-adr = <20>;
|
|
cavium,t-ce = <60>;
|
|
cavium,t-oe = <60>;
|
|
cavium,t-we = <45>;
|
|
cavium,t-rd-hld = <35>;
|
|
cavium,t-wr-hld = <45>;
|
|
cavium,t-pause = <0>;
|
|
cavium,t-wait = <0>;
|
|
cavium,t-page = <35>;
|
|
cavium,t-rd-dly = <0>;
|
|
|
|
cavium,pages = <0>;
|
|
cavium,bus-width = <8>;
|
|
};
|
|
cavium,cs-config@4 {
|
|
compatible = "cavium,octeon-3860-bootbus-config";
|
|
cavium,cs-index = <4>;
|
|
cavium,t-adr = <320>;
|
|
cavium,t-ce = <320>;
|
|
cavium,t-oe = <320>;
|
|
cavium,t-we = <320>;
|
|
cavium,t-rd-hld = <320>;
|
|
cavium,t-wr-hld = <320>;
|
|
cavium,t-pause = <320>;
|
|
cavium,t-wait = <320>;
|
|
cavium,t-page = <320>;
|
|
cavium,t-rd-dly = <0>;
|
|
|
|
cavium,pages = <0>;
|
|
cavium,bus-width = <8>;
|
|
};
|
|
cavium,cs-config@5 {
|
|
compatible = "cavium,octeon-3860-bootbus-config";
|
|
cavium,cs-index = <5>;
|
|
cavium,t-adr = <5>;
|
|
cavium,t-ce = <300>;
|
|
cavium,t-oe = <125>;
|
|
cavium,t-we = <150>;
|
|
cavium,t-rd-hld = <100>;
|
|
cavium,t-wr-hld = <30>;
|
|
cavium,t-pause = <0>;
|
|
cavium,t-wait = <30>;
|
|
cavium,t-page = <320>;
|
|
cavium,t-rd-dly = <0>;
|
|
|
|
cavium,pages = <0>;
|
|
cavium,bus-width = <16>;
|
|
};
|
|
cavium,cs-config@6 {
|
|
compatible = "cavium,octeon-3860-bootbus-config";
|
|
cavium,cs-index = <6>;
|
|
cavium,t-adr = <5>;
|
|
cavium,t-ce = <300>;
|
|
cavium,t-oe = <270>;
|
|
cavium,t-we = <150>;
|
|
cavium,t-rd-hld = <100>;
|
|
cavium,t-wr-hld = <70>;
|
|
cavium,t-pause = <0>;
|
|
cavium,t-wait = <0>;
|
|
cavium,t-page = <320>;
|
|
cavium,t-rd-dly = <0>;
|
|
|
|
cavium,pages = <0>;
|
|
cavium,wait-mode;
|
|
cavium,bus-width = <16>;
|
|
};
|
|
|
|
flash0: nor@0,0 {
|
|
compatible = "cfi-flash";
|
|
reg = <0 0 0x800000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
};
|
|
|
|
led0: led-display@4,0 {
|
|
compatible = "avago,hdsp-253x";
|
|
reg = <4 0x20 0x20>, <4 0 0x20>;
|
|
};
|
|
|
|
cf0: compact-flash@5,0 {
|
|
compatible = "cavium,ebt3000-compact-flash";
|
|
reg = <5 0 0x10000>, <6 0 0x10000>;
|
|
cavium,bus-width = <16>;
|
|
cavium,true-ide;
|
|
cavium,dma-engine-handle = <&dma0>;
|
|
};
|
|
};
|
|
|
|
dma0: dma-engine@1180000000100 {
|
|
compatible = "cavium,octeon-5750-bootbus-dma";
|
|
reg = <0x11800 0x00000100 0x0 0x8>;
|
|
interrupts = <0 63>;
|
|
};
|
|
dma1: dma-engine@1180000000108 {
|
|
compatible = "cavium,octeon-5750-bootbus-dma";
|
|
reg = <0x11800 0x00000108 0x0 0x8>;
|
|
interrupts = <0 63>;
|
|
};
|
|
|
|
uctl: uctl@118006f000000 {
|
|
compatible = "cavium,octeon-6335-uctl";
|
|
reg = <0x11800 0x6f000000 0x0 0x100>;
|
|
ranges; /* Direct mapping */
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
/* 12MHz, 24MHz and 48MHz allowed */
|
|
refclk-frequency = <12000000>;
|
|
/* Either "crystal" or "external" */
|
|
refclk-type = "crystal";
|
|
|
|
ehci@16f0000000000 {
|
|
compatible = "cavium,octeon-6335-ehci","usb-ehci";
|
|
reg = <0x16f00 0x00000000 0x0 0x100>;
|
|
interrupts = <0 56>;
|
|
big-endian-regs;
|
|
};
|
|
ohci@16f0000000400 {
|
|
compatible = "cavium,octeon-6335-ohci","usb-ohci";
|
|
reg = <0x16f00 0x00000400 0x0 0x100>;
|
|
interrupts = <0 56>;
|
|
big-endian-regs;
|
|
};
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
mix0 = &mix0;
|
|
mix1 = &mix1;
|
|
pip = &pip;
|
|
smi0 = &smi0;
|
|
smi1 = &smi1;
|
|
twsi0 = &twsi0;
|
|
twsi1 = &twsi1;
|
|
uart0 = &uart0;
|
|
uart1 = &uart1;
|
|
uart2 = &uart2;
|
|
flash0 = &flash0;
|
|
cf0 = &cf0;
|
|
uctl = &uctl;
|
|
led0 = &led0;
|
|
};
|
|
};
|