3b098e2d7c
With RPS inclusion, skb timestamping is not consistent in RX path. If netif_receive_skb() is used, its deferred after RPS dispatch. If netif_rx() is used, its done before RPS dispatch. This can give strange tcpdump timestamps results. I think timestamping should be done as soon as possible in the receive path, to get meaningful values (ie timestamps taken at the time packet was delivered by NIC driver to our stack), even if NAPI already can defer timestamping a bit (RPS can help to reduce the gap) Tom Herbert prefer to sample timestamps after RPS dispatch. In case sampling is expensive (HPET/acpi_pm on x86), this makes sense. Let admins switch from one mode to another, using a new sysctl, /proc/sys/net/core/netdev_tstamp_prequeue Its default value (1), means timestamps are taken as soon as possible, before backlog queueing, giving accurate timestamps. Setting a 0 value permits to sample timestamps when processing backlog, after RPS dispatch, to lower the load of the pre-RPS cpu. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
186 lines
6.6 KiB
Plaintext
186 lines
6.6 KiB
Plaintext
Documentation for /proc/sys/net/* kernel version 2.4.0-test11-pre4
|
|
(c) 1999 Terrehon Bowden <terrehon@pacbell.net>
|
|
Bodo Bauer <bb@ricochet.net>
|
|
(c) 2000 Jorge Nerin <comandante@zaralinux.com>
|
|
(c) 2009 Shen Feng <shen@cn.fujitsu.com>
|
|
|
|
For general info and legal blurb, please look in README.
|
|
|
|
==============================================================
|
|
|
|
This file contains the documentation for the sysctl files in
|
|
/proc/sys/net and is valid for Linux kernel version 2.4.0-test11-pre4.
|
|
|
|
The interface to the networking parts of the kernel is located in
|
|
/proc/sys/net. The following table shows all possible subdirectories.You may
|
|
see only some of them, depending on your kernel's configuration.
|
|
|
|
|
|
Table : Subdirectories in /proc/sys/net
|
|
..............................................................................
|
|
Directory Content Directory Content
|
|
core General parameter appletalk Appletalk protocol
|
|
unix Unix domain sockets netrom NET/ROM
|
|
802 E802 protocol ax25 AX25
|
|
ethernet Ethernet protocol rose X.25 PLP layer
|
|
ipv4 IP version 4 x25 X.25 protocol
|
|
ipx IPX token-ring IBM token ring
|
|
bridge Bridging decnet DEC net
|
|
ipv6 IP version 6
|
|
..............................................................................
|
|
|
|
1. /proc/sys/net/core - Network core options
|
|
-------------------------------------------------------
|
|
|
|
rmem_default
|
|
------------
|
|
|
|
The default setting of the socket receive buffer in bytes.
|
|
|
|
rmem_max
|
|
--------
|
|
|
|
The maximum receive socket buffer size in bytes.
|
|
|
|
wmem_default
|
|
------------
|
|
|
|
The default setting (in bytes) of the socket send buffer.
|
|
|
|
wmem_max
|
|
--------
|
|
|
|
The maximum send socket buffer size in bytes.
|
|
|
|
message_burst and message_cost
|
|
------------------------------
|
|
|
|
These parameters are used to limit the warning messages written to the kernel
|
|
log from the networking code. They enforce a rate limit to make a
|
|
denial-of-service attack impossible. A higher message_cost factor, results in
|
|
fewer messages that will be written. Message_burst controls when messages will
|
|
be dropped. The default settings limit warning messages to one every five
|
|
seconds.
|
|
|
|
warnings
|
|
--------
|
|
|
|
This controls console messages from the networking stack that can occur because
|
|
of problems on the network like duplicate address or bad checksums. Normally,
|
|
this should be enabled, but if the problem persists the messages can be
|
|
disabled.
|
|
|
|
netdev_budget
|
|
-------------
|
|
|
|
Maximum number of packets taken from all interfaces in one polling cycle (NAPI
|
|
poll). In one polling cycle interfaces which are registered to polling are
|
|
probed in a round-robin manner. The limit of packets in one such probe can be
|
|
set per-device via sysfs class/net/<device>/weight .
|
|
|
|
netdev_max_backlog
|
|
------------------
|
|
|
|
Maximum number of packets, queued on the INPUT side, when the interface
|
|
receives packets faster than kernel can process them.
|
|
|
|
netdev_tstamp_prequeue
|
|
----------------------
|
|
|
|
If set to 0, RX packet timestamps can be sampled after RPS processing, when
|
|
the target CPU processes packets. It might give some delay on timestamps, but
|
|
permit to distribute the load on several cpus.
|
|
|
|
If set to 1 (default), timestamps are sampled as soon as possible, before
|
|
queueing.
|
|
|
|
optmem_max
|
|
----------
|
|
|
|
Maximum ancillary buffer size allowed per socket. Ancillary data is a sequence
|
|
of struct cmsghdr structures with appended data.
|
|
|
|
2. /proc/sys/net/unix - Parameters for Unix domain sockets
|
|
-------------------------------------------------------
|
|
|
|
There is only one file in this directory.
|
|
unix_dgram_qlen limits the max number of datagrams queued in Unix domain
|
|
socket's buffer. It will not take effect unless PF_UNIX flag is specified.
|
|
|
|
|
|
3. /proc/sys/net/ipv4 - IPV4 settings
|
|
-------------------------------------------------------
|
|
Please see: Documentation/networking/ip-sysctl.txt and ipvs-sysctl.txt for
|
|
descriptions of these entries.
|
|
|
|
|
|
4. Appletalk
|
|
-------------------------------------------------------
|
|
|
|
The /proc/sys/net/appletalk directory holds the Appletalk configuration data
|
|
when Appletalk is loaded. The configurable parameters are:
|
|
|
|
aarp-expiry-time
|
|
----------------
|
|
|
|
The amount of time we keep an ARP entry before expiring it. Used to age out
|
|
old hosts.
|
|
|
|
aarp-resolve-time
|
|
-----------------
|
|
|
|
The amount of time we will spend trying to resolve an Appletalk address.
|
|
|
|
aarp-retransmit-limit
|
|
---------------------
|
|
|
|
The number of times we will retransmit a query before giving up.
|
|
|
|
aarp-tick-time
|
|
--------------
|
|
|
|
Controls the rate at which expires are checked.
|
|
|
|
The directory /proc/net/appletalk holds the list of active Appletalk sockets
|
|
on a machine.
|
|
|
|
The fields indicate the DDP type, the local address (in network:node format)
|
|
the remote address, the size of the transmit pending queue, the size of the
|
|
received queue (bytes waiting for applications to read) the state and the uid
|
|
owning the socket.
|
|
|
|
/proc/net/atalk_iface lists all the interfaces configured for appletalk.It
|
|
shows the name of the interface, its Appletalk address, the network range on
|
|
that address (or network number for phase 1 networks), and the status of the
|
|
interface.
|
|
|
|
/proc/net/atalk_route lists each known network route. It lists the target
|
|
(network) that the route leads to, the router (may be directly connected), the
|
|
route flags, and the device the route is using.
|
|
|
|
|
|
5. IPX
|
|
-------------------------------------------------------
|
|
|
|
The IPX protocol has no tunable values in proc/sys/net.
|
|
|
|
The IPX protocol does, however, provide proc/net/ipx. This lists each IPX
|
|
socket giving the local and remote addresses in Novell format (that is
|
|
network:node:port). In accordance with the strange Novell tradition,
|
|
everything but the port is in hex. Not_Connected is displayed for sockets that
|
|
are not tied to a specific remote address. The Tx and Rx queue sizes indicate
|
|
the number of bytes pending for transmission and reception. The state
|
|
indicates the state the socket is in and the uid is the owning uid of the
|
|
socket.
|
|
|
|
The /proc/net/ipx_interface file lists all IPX interfaces. For each interface
|
|
it gives the network number, the node number, and indicates if the network is
|
|
the primary network. It also indicates which device it is bound to (or
|
|
Internal for internal networks) and the Frame Type if appropriate. Linux
|
|
supports 802.3, 802.2, 802.2 SNAP and DIX (Blue Book) ethernet framing for
|
|
IPX.
|
|
|
|
The /proc/net/ipx_route table holds a list of IPX routes. For each route it
|
|
gives the destination network, the router node (or Directly) and the network
|
|
address of the router (or Connected) for internal networks.
|