kernel-ark/drivers/ide/pci/aec62xx.c
Bartlomiej Zolnierkiewicz 4099d14322 ide: add PIO masks
* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:59 +02:00

359 lines
10 KiB
C

/*
* linux/drivers/ide/pci/aec62xx.c Version 0.24 May 24, 2007
*
* Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2007 MontaVista Software, Inc. <source@mvista.com>
*
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <asm/io.h>
struct chipset_bus_clock_list_entry {
u8 xfer_speed;
u8 chipset_settings;
u8 ultra_settings;
};
static const struct chipset_bus_clock_list_entry aec6xxx_33_base [] = {
{ XFER_UDMA_6, 0x31, 0x07 },
{ XFER_UDMA_5, 0x31, 0x06 },
{ XFER_UDMA_4, 0x31, 0x05 },
{ XFER_UDMA_3, 0x31, 0x04 },
{ XFER_UDMA_2, 0x31, 0x03 },
{ XFER_UDMA_1, 0x31, 0x02 },
{ XFER_UDMA_0, 0x31, 0x01 },
{ XFER_MW_DMA_2, 0x31, 0x00 },
{ XFER_MW_DMA_1, 0x31, 0x00 },
{ XFER_MW_DMA_0, 0x0a, 0x00 },
{ XFER_PIO_4, 0x31, 0x00 },
{ XFER_PIO_3, 0x33, 0x00 },
{ XFER_PIO_2, 0x08, 0x00 },
{ XFER_PIO_1, 0x0a, 0x00 },
{ XFER_PIO_0, 0x00, 0x00 },
{ 0, 0x00, 0x00 }
};
static const struct chipset_bus_clock_list_entry aec6xxx_34_base [] = {
{ XFER_UDMA_6, 0x41, 0x06 },
{ XFER_UDMA_5, 0x41, 0x05 },
{ XFER_UDMA_4, 0x41, 0x04 },
{ XFER_UDMA_3, 0x41, 0x03 },
{ XFER_UDMA_2, 0x41, 0x02 },
{ XFER_UDMA_1, 0x41, 0x01 },
{ XFER_UDMA_0, 0x41, 0x01 },
{ XFER_MW_DMA_2, 0x41, 0x00 },
{ XFER_MW_DMA_1, 0x42, 0x00 },
{ XFER_MW_DMA_0, 0x7a, 0x00 },
{ XFER_PIO_4, 0x41, 0x00 },
{ XFER_PIO_3, 0x43, 0x00 },
{ XFER_PIO_2, 0x78, 0x00 },
{ XFER_PIO_1, 0x7a, 0x00 },
{ XFER_PIO_0, 0x70, 0x00 },
{ 0, 0x00, 0x00 }
};
#define BUSCLOCK(D) \
((struct chipset_bus_clock_list_entry *) pci_get_drvdata((D)))
/*
* TO DO: active tuning and correction of cards without a bios.
*/
static u8 pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table)
{
for ( ; chipset_table->xfer_speed ; chipset_table++)
if (chipset_table->xfer_speed == speed) {
return chipset_table->chipset_settings;
}
return chipset_table->chipset_settings;
}
static u8 pci_bus_clock_list_ultra (u8 speed, struct chipset_bus_clock_list_entry * chipset_table)
{
for ( ; chipset_table->xfer_speed ; chipset_table++)
if (chipset_table->xfer_speed == speed) {
return chipset_table->ultra_settings;
}
return chipset_table->ultra_settings;
}
static int aec6210_tune_chipset (ide_drive_t *drive, u8 xferspeed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
u16 d_conf = 0;
u8 speed = ide_rate_filter(drive, xferspeed);
u8 ultra = 0, ultra_conf = 0;
u8 tmp0 = 0, tmp1 = 0, tmp2 = 0;
unsigned long flags;
local_irq_save(flags);
/* 0x40|(2*drive->dn): Active, 0x41|(2*drive->dn): Recovery */
pci_read_config_word(dev, 0x40|(2*drive->dn), &d_conf);
tmp0 = pci_bus_clock_list(speed, BUSCLOCK(dev));
d_conf = ((tmp0 & 0xf0) << 4) | (tmp0 & 0xf);
pci_write_config_word(dev, 0x40|(2*drive->dn), d_conf);
tmp1 = 0x00;
tmp2 = 0x00;
pci_read_config_byte(dev, 0x54, &ultra);
tmp1 = ((0x00 << (2*drive->dn)) | (ultra & ~(3 << (2*drive->dn))));
ultra_conf = pci_bus_clock_list_ultra(speed, BUSCLOCK(dev));
tmp2 = ((ultra_conf << (2*drive->dn)) | (tmp1 & ~(3 << (2*drive->dn))));
pci_write_config_byte(dev, 0x54, tmp2);
local_irq_restore(flags);
return(ide_config_drive_speed(drive, speed));
}
static int aec6260_tune_chipset (ide_drive_t *drive, u8 xferspeed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
u8 speed = ide_rate_filter(drive, xferspeed);
u8 unit = (drive->select.b.unit & 0x01);
u8 tmp1 = 0, tmp2 = 0;
u8 ultra = 0, drive_conf = 0, ultra_conf = 0;
unsigned long flags;
local_irq_save(flags);
/* high 4-bits: Active, low 4-bits: Recovery */
pci_read_config_byte(dev, 0x40|drive->dn, &drive_conf);
drive_conf = pci_bus_clock_list(speed, BUSCLOCK(dev));
pci_write_config_byte(dev, 0x40|drive->dn, drive_conf);
pci_read_config_byte(dev, (0x44|hwif->channel), &ultra);
tmp1 = ((0x00 << (4*unit)) | (ultra & ~(7 << (4*unit))));
ultra_conf = pci_bus_clock_list_ultra(speed, BUSCLOCK(dev));
tmp2 = ((ultra_conf << (4*unit)) | (tmp1 & ~(7 << (4*unit))));
pci_write_config_byte(dev, (0x44|hwif->channel), tmp2);
local_irq_restore(flags);
return(ide_config_drive_speed(drive, speed));
}
static void aec62xx_tune_drive (ide_drive_t *drive, u8 pio)
{
pio = ide_get_best_pio_mode(drive, pio, 4);
(void) HWIF(drive)->speedproc(drive, pio + XFER_PIO_0);
}
static int aec62xx_config_drive_xfer_rate (ide_drive_t *drive)
{
if (ide_tune_dma(drive))
return 0;
if (ide_use_fast_pio(drive))
aec62xx_tune_drive(drive, 255);
return -1;
}
static void aec62xx_dma_lost_irq (ide_drive_t *drive)
{
switch (HWIF(drive)->pci_dev->device) {
case PCI_DEVICE_ID_ARTOP_ATP860:
case PCI_DEVICE_ID_ARTOP_ATP860R:
case PCI_DEVICE_ID_ARTOP_ATP865:
case PCI_DEVICE_ID_ARTOP_ATP865R:
printk(" AEC62XX time out ");
default:
break;
}
}
static unsigned int __devinit init_chipset_aec62xx(struct pci_dev *dev, const char *name)
{
int bus_speed = system_bus_clock();
if (bus_speed <= 33)
pci_set_drvdata(dev, (void *) aec6xxx_33_base);
else
pci_set_drvdata(dev, (void *) aec6xxx_34_base);
/* These are necessary to get AEC6280 Macintosh cards to work */
if ((dev->device == PCI_DEVICE_ID_ARTOP_ATP865) ||
(dev->device == PCI_DEVICE_ID_ARTOP_ATP865R)) {
u8 reg49h = 0, reg4ah = 0;
/* Clear reset and test bits. */
pci_read_config_byte(dev, 0x49, &reg49h);
pci_write_config_byte(dev, 0x49, reg49h & ~0x30);
/* Enable chip interrupt output. */
pci_read_config_byte(dev, 0x4a, &reg4ah);
pci_write_config_byte(dev, 0x4a, reg4ah & ~0x01);
/* Enable burst mode. */
pci_read_config_byte(dev, 0x4a, &reg4ah);
pci_write_config_byte(dev, 0x4a, reg4ah | 0x80);
}
return dev->irq;
}
static void __devinit init_hwif_aec62xx(ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
u8 reg54 = 0, mask = hwif->channel ? 0xf0 : 0x0f;
unsigned long flags;
hwif->tuneproc = &aec62xx_tune_drive;
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
if(hwif->mate)
hwif->mate->serialized = hwif->serialized = 1;
hwif->speedproc = &aec6210_tune_chipset;
} else
hwif->speedproc = &aec6260_tune_chipset;
if (!hwif->dma_base) {
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
return;
}
hwif->ultra_mask = hwif->cds->udma_mask;
hwif->mwdma_mask = 0x07;
hwif->ide_dma_check = &aec62xx_config_drive_xfer_rate;
hwif->dma_lost_irq = &aec62xx_dma_lost_irq;
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
spin_lock_irqsave(&ide_lock, flags);
pci_read_config_byte (dev, 0x54, &reg54);
pci_write_config_byte(dev, 0x54, (reg54 & ~mask));
spin_unlock_irqrestore(&ide_lock, flags);
} else if (hwif->cbl != ATA_CBL_PATA40_SHORT) {
u8 ata66 = 0, mask = hwif->channel ? 0x02 : 0x01;
pci_read_config_byte(hwif->pci_dev, 0x49, &ata66);
hwif->cbl = (ata66 & mask) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma;
}
static int __devinit init_setup_aec62xx(struct pci_dev *dev, ide_pci_device_t *d)
{
return ide_setup_pci_device(dev, d);
}
static int __devinit init_setup_aec6x80(struct pci_dev *dev, ide_pci_device_t *d)
{
unsigned long dma_base = pci_resource_start(dev, 4);
if (inb(dma_base + 2) & 0x10) {
d->name = (dev->device == PCI_DEVICE_ID_ARTOP_ATP865R) ?
"AEC6880R" : "AEC6880";
d->udma_mask = 0x7f; /* udma0-6 */
}
return ide_setup_pci_device(dev, d);
}
static ide_pci_device_t aec62xx_chipsets[] __devinitdata = {
{ /* 0 */
.name = "AEC6210",
.init_setup = init_setup_aec62xx,
.init_chipset = init_chipset_aec62xx,
.init_hwif = init_hwif_aec62xx,
.autodma = AUTODMA,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x07, /* udma0-2 */
},{ /* 1 */
.name = "AEC6260",
.init_setup = init_setup_aec62xx,
.init_chipset = init_chipset_aec62xx,
.init_hwif = init_hwif_aec62xx,
.autodma = NOAUTODMA,
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x1f, /* udma0-4 */
},{ /* 2 */
.name = "AEC6260R",
.init_setup = init_setup_aec62xx,
.init_chipset = init_chipset_aec62xx,
.init_hwif = init_hwif_aec62xx,
.autodma = AUTODMA,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
.bootable = NEVER_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x1f, /* udma0-4 */
},{ /* 3 */
.name = "AEC6280",
.init_setup = init_setup_aec6x80,
.init_chipset = init_chipset_aec62xx,
.init_hwif = init_hwif_aec62xx,
.autodma = AUTODMA,
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x3f, /* udma0-5 */
},{ /* 4 */
.name = "AEC6280R",
.init_setup = init_setup_aec6x80,
.init_chipset = init_chipset_aec62xx,
.init_hwif = init_hwif_aec62xx,
.autodma = AUTODMA,
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x3f, /* udma0-5 */
}
};
/**
* aec62xx_init_one - called when a AEC is found
* @dev: the aec62xx device
* @id: the matching pci id
*
* Called when the PCI registration layer (or the IDE initialization)
* finds a device matching our IDE device tables.
*
* NOTE: since we're going to modify the 'name' field for AEC-6[26]80[R]
* chips, pass a local copy of 'struct pci_device_id' down the call chain.
*/
static int __devinit aec62xx_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
ide_pci_device_t d = aec62xx_chipsets[id->driver_data];
return d.init_setup(dev, &d);
}
static struct pci_device_id aec62xx_pci_tbl[] = {
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP850UF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP860, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP860R, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP865, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP865R, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, aec62xx_pci_tbl);
static struct pci_driver driver = {
.name = "AEC62xx_IDE",
.id_table = aec62xx_pci_tbl,
.probe = aec62xx_init_one,
};
static int __init aec62xx_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
module_init(aec62xx_ide_init);
MODULE_AUTHOR("Andre Hedrick");
MODULE_DESCRIPTION("PCI driver module for ARTOP AEC62xx IDE");
MODULE_LICENSE("GPL");