kernel-ark/drivers/net/mipsnet.h
Ralf Baechle c2af68e5f5 MIPSsim: General cleanup
General cleanups mostly as suggested by checkpatch plus getting rid of
homebrew version of offsetof().

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15 14:29:49 -04:00

113 lines
3.5 KiB
C

/*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
#ifndef __MIPSNET_H
#define __MIPSNET_H
/*
* Id of this Net device, as seen by the core.
*/
#define MIPS_NET_DEV_ID ((uint64_t) \
((uint64_t) 'M' << 0)| \
((uint64_t) 'I' << 8)| \
((uint64_t) 'P' << 16)| \
((uint64_t) 'S' << 24)| \
((uint64_t) 'N' << 32)| \
((uint64_t) 'E' << 40)| \
((uint64_t) 'T' << 48)| \
((uint64_t) '0' << 56))
/*
* Net status/control block as seen by sw in the core.
* (Why not use bit fields? can't be bothered with cross-platform struct
* packing.)
*/
struct net_control_block {
/*
* dev info for probing
* reads as MIPSNET%d where %d is some form of version
*/
uint64_t devId; /* 0x00 */
/*
* read only busy flag.
* Set and cleared by the Net Device to indicate that an rx or a tx
* is in progress.
*/
uint32_t busy; /* 0x08 */
/*
* Set by the Net Device.
* The device will set it once data has been received.
* The value is the number of bytes that should be read from
* rxDataBuffer. The value will decrease till 0 until all the data
* from rxDataBuffer has been read.
*/
uint32_t rxDataCount; /* 0x0c */
#define MIPSNET_MAX_RXTX_DATACOUNT (1<<16)
/*
* Settable from the MIPS core, cleared by the Net Device. The core
* should set the number of bytes it wants to send, then it should
* write those bytes of data to txDataBuffer. The device will clear
* txDataCount has been processed (not necessarily sent).
*/
uint32_t txDataCount; /* 0x10 */
/*
* Interrupt control
*
* Used to clear the interrupted generated by this dev.
* Write a 1 to clear the interrupt. (except bit31).
*
* Bit0 is set if it was a tx-done interrupt.
* Bit1 is set when new rx-data is available.
* Until this bit is cleared there will be no other RXs.
*
* Bit31 is used for testing, it clears after a read.
* Writing 1 to this bit will cause an interrupt to be generated.
* To clear the test interrupt, write 0 to this register.
*/
uint32_t interruptControl; /*0x14 */
#define MIPSNET_INTCTL_TXDONE ((uint32_t)(1 << 0))
#define MIPSNET_INTCTL_RXDONE ((uint32_t)(1 << 1))
#define MIPSNET_INTCTL_TESTBIT ((uint32_t)(1 << 31))
#define MIPSNET_INTCTL_ALLSOURCES (MIPSNET_INTCTL_TXDONE | \
MIPSNET_INTCTL_RXDONE | \
MIPSNET_INTCTL_TESTBIT)
/*
* Readonly core-specific interrupt info for the device to signal the
* core. The meaning of the contents of this field might change.
*
* TODO: the whole memIntf interrupt scheme is messy: the device should
* have no control what so ever of what VPE/register set is being
* used. The MemIntf should only expose interrupt lines, and
* something in the config should be responsible for the
* line<->core/vpe bindings.
*/
uint32_t interruptInfo; /* 0x18 */
/*
* This is where the received data is read out.
* There is more data to read until rxDataReady is 0.
* Only 1 byte at this regs offset is used.
*/
uint32_t rxDataBuffer; /* 0x1c */
/*
* This is where the data to transmit is written. Data should be
* written for the amount specified in the txDataCount register. Only
* 1 byte at this regs offset is used.
*/
uint32_t txDataBuffer; /* 0x20 */
};
#define MIPSNET_IO_EXTENT 0x40 /* being generous */
#define field_offset(field) (offsetof(struct net_control_block, field))
#endif /* __MIPSNET_H */