davidlt/kernel-ark
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
d9ddd62943
kernel-ark/include/linux/mmc/host.h
Girish K S bec8726abc mmc: core: Add Power Off Notify Feature eMMC 4.5 
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).

For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:23 -04:00

423 lines
15 KiB
C
Raw Blame History

/*
* linux/include/linux/mmc/host.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Host driver specific definitions.
*/
#ifndef LINUX_MMC_HOST_H
#define LINUX_MMC_HOST_H
#include <linux/leds.h>
#include <linux/sched.h>
#include <linux/fault-inject.h>
#include <linux/mmc/core.h>
#include <linux/mmc/pm.h>
struct mmc_ios {
unsigned int clock; /* clock rate */
unsigned short vdd;
/* vdd stores the bit number of the selected voltage range from below. */
unsigned char bus_mode; /* command output mode */
#define MMC_BUSMODE_OPENDRAIN 1
#define MMC_BUSMODE_PUSHPULL 2
unsigned char chip_select; /* SPI chip select */
#define MMC_CS_DONTCARE 0
#define MMC_CS_HIGH 1
#define MMC_CS_LOW 2
unsigned char power_mode; /* power supply mode */
#define MMC_POWER_OFF 0
#define MMC_POWER_UP 1
#define MMC_POWER_ON 2
unsigned char bus_width; /* data bus width */
#define MMC_BUS_WIDTH_1 0
#define MMC_BUS_WIDTH_4 2
#define MMC_BUS_WIDTH_8 3
unsigned char timing; /* timing specification used */
#define MMC_TIMING_LEGACY 0
#define MMC_TIMING_MMC_HS 1
#define MMC_TIMING_SD_HS 2
#define MMC_TIMING_UHS_SDR12 MMC_TIMING_LEGACY
#define MMC_TIMING_UHS_SDR25 MMC_TIMING_SD_HS
#define MMC_TIMING_UHS_SDR50 3
#define MMC_TIMING_UHS_SDR104 4
#define MMC_TIMING_UHS_DDR50 5
#define MMC_SDR_MODE 0
#define MMC_1_2V_DDR_MODE 1
#define MMC_1_8V_DDR_MODE 2
unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
#define MMC_SIGNAL_VOLTAGE_330 0
#define MMC_SIGNAL_VOLTAGE_180 1
#define MMC_SIGNAL_VOLTAGE_120 2
unsigned char drv_type; /* driver type (A, B, C, D) */
#define MMC_SET_DRIVER_TYPE_B 0
#define MMC_SET_DRIVER_TYPE_A 1
#define MMC_SET_DRIVER_TYPE_C 2
#define MMC_SET_DRIVER_TYPE_D 3
};
struct mmc_host_ops {
/*
* Hosts that support power saving can use the 'enable' and 'disable'
* methods to exit and enter power saving states. 'enable' is called
* when the host is claimed and 'disable' is called (or scheduled with
* a delay) when the host is released. The 'disable' is scheduled if
* the disable delay set by 'mmc_set_disable_delay()' is non-zero,
* otherwise 'disable' is called immediately. 'disable' may be
* scheduled repeatedly, to permit ever greater power saving at the
* expense of ever greater latency to re-enable. Rescheduling is
* determined by the return value of the 'disable' method. A positive
* value gives the delay in milliseconds.
*
* In the case where a host function (like set_ios) may be called
* with or without the host claimed, enabling and disabling can be
* done directly and will nest correctly. Call 'mmc_host_enable()' and
* 'mmc_host_lazy_disable()' for this purpose, but note that these
* functions must be paired.
*
* Alternatively, 'mmc_host_enable()' may be paired with
* 'mmc_host_disable()' which calls 'disable' immediately. In this
* case the 'disable' method will be called with 'lazy' set to 0.
* This is mainly useful for error paths.
*
* Because lazy disable may be called from a work queue, the 'disable'
* method must claim the host when 'lazy' != 0, which will work
* correctly because recursion is detected and handled.
*/
int (*enable)(struct mmc_host *host);
int (*disable)(struct mmc_host *host, int lazy);
/*
* It is optional for the host to implement pre_req and post_req in
* order to support double buffering of requests (prepare one
* request while another request is active).
* pre_req() must always be followed by a post_req().
* To undo a call made to pre_req(), call post_req() with
* a nonzero err condition.
*/
void (*post_req)(struct mmc_host *host, struct mmc_request *req,
int err);
void (*pre_req)(struct mmc_host *host, struct mmc_request *req,
bool is_first_req);
void (*request)(struct mmc_host *host, struct mmc_request *req);
/*
* Avoid calling these three functions too often or in a "fast path",
* since underlaying controller might implement them in an expensive
* and/or slow way.
*
* Also note that these functions might sleep, so don't call them
* in the atomic contexts!
*
* Return values for the get_ro callback should be:
* 0 for a read/write card
* 1 for a read-only card
* -ENOSYS when not supported (equal to NULL callback)
* or a negative errno value when something bad happened
*
* Return values for the get_cd callback should be:
* 0 for a absent card
* 1 for a present card
* -ENOSYS when not supported (equal to NULL callback)
* or a negative errno value when something bad happened
*/
void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios);
int (*get_ro)(struct mmc_host *host);
int (*get_cd)(struct mmc_host *host);
void (*enable_sdio_irq)(struct mmc_host *host, int enable);
/* optional callback for HC quirks */
void (*init_card)(struct mmc_host *host, struct mmc_card *card);
int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
int (*execute_tuning)(struct mmc_host *host);
void (*enable_preset_value)(struct mmc_host *host, bool enable);
int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
void (*hw_reset)(struct mmc_host *host);
};
struct mmc_card;
struct device;
struct mmc_async_req {
/* active mmc request */
struct mmc_request *mrq;
/*
* Check error status of completed mmc request.
* Returns 0 if success otherwise non zero.
*/
int (*err_check) (struct mmc_card *, struct mmc_async_req *);
};
struct mmc_host {
struct device *parent;
struct device class_dev;
int index;
const struct mmc_host_ops *ops;
unsigned int f_min;
unsigned int f_max;
unsigned int f_init;
u32 ocr_avail;
u32 ocr_avail_sdio; /* SDIO-specific OCR */
u32 ocr_avail_sd; /* SD-specific OCR */
u32 ocr_avail_mmc; /* MMC-specific OCR */
struct notifier_block pm_notify;
#define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
#define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
#define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */
#define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */
#define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */
#define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */
#define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */
#define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */
#define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */
#define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */
#define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */
#define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */
#define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */
#define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */
#define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
#define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
#define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
unsigned long caps; /* Host capabilities */
#define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */
#define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */
#define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */
#define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */
#define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */
#define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */
#define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */
#define MMC_CAP_DISABLE (1 << 7) /* Can the host be disabled */
#define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */
#define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */
#define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */
#define MMC_CAP_1_8V_DDR (1 << 11) /* can support */
/* DDR mode at 1.8V */
#define MMC_CAP_1_2V_DDR (1 << 12) /* can support */
/* DDR mode at 1.2V */
#define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */
#define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */
#define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */
#define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */
#define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */
#define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */
#define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */
#define MMC_CAP_SET_XPC_330 (1 << 20) /* Host supports >150mA current at 3.3V */
#define MMC_CAP_SET_XPC_300 (1 << 21) /* Host supports >150mA current at 3.0V */
#define MMC_CAP_SET_XPC_180 (1 << 22) /* Host supports >150mA current at 1.8V */
#define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */
#define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */
#define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */
#define MMC_CAP_MAX_CURRENT_200 (1 << 26) /* Host max current limit is 200mA */
#define MMC_CAP_MAX_CURRENT_400 (1 << 27) /* Host max current limit is 400mA */
#define MMC_CAP_MAX_CURRENT_600 (1 << 28) /* Host max current limit is 600mA */
#define MMC_CAP_MAX_CURRENT_800 (1 << 29) /* Host max current limit is 800mA */
#define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */
#define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */
unsigned int caps2; /* More host capabilities */
#define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */
#define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff supported */
mmc_pm_flag_t pm_caps; /* supported pm features */
unsigned int power_notify_type;
#define MMC_HOST_PW_NOTIFY_NONE 0
#define MMC_HOST_PW_NOTIFY_SHORT 1
#define MMC_HOST_PW_NOTIFY_LONG 2
#ifdef CONFIG_MMC_CLKGATE
int clk_requests; /* internal reference counter */
unsigned int clk_delay; /* number of MCI clk hold cycles */
bool clk_gated; /* clock gated */
struct work_struct clk_gate_work; /* delayed clock gate */
unsigned int clk_old; /* old clock value cache */
spinlock_t clk_lock; /* lock for clk fields */
struct mutex clk_gate_mutex; /* mutex for clock gating */
#endif
/* host specific block data */
unsigned int max_seg_size; /* see blk_queue_max_segment_size */
unsigned short max_segs; /* see blk_queue_max_segments */
unsigned short unused;
unsigned int max_req_size; /* maximum number of bytes in one req */
unsigned int max_blk_size; /* maximum size of one mmc block */
unsigned int max_blk_count; /* maximum number of blocks in one req */
unsigned int max_discard_to; /* max. discard timeout in ms */
/* private data */
spinlock_t lock; /* lock for claim and bus ops */
struct mmc_ios ios; /* current io bus settings */
u32 ocr; /* the current OCR setting */
/* group bitfields together to minimize padding */
unsigned int use_spi_crc:1;
unsigned int claimed:1; /* host exclusively claimed */
unsigned int bus_dead:1; /* bus has been released */
#ifdef CONFIG_MMC_DEBUG
unsigned int removed:1; /* host is being removed */
#endif
/* Only used with MMC_CAP_DISABLE */
int enabled; /* host is enabled */
int rescan_disable; /* disable card detection */
int nesting_cnt; /* "enable" nesting count */
int en_dis_recurs; /* detect recursion */
unsigned int disable_delay; /* disable delay in msecs */
struct delayed_work disable; /* disabling work */
struct mmc_card *card; /* device attached to this host */
wait_queue_head_t wq;
struct task_struct *claimer; /* task that has host claimed */
int claim_cnt; /* "claim" nesting count */
struct delayed_work detect;
const struct mmc_bus_ops *bus_ops; /* current bus driver */
unsigned int bus_refs; /* reference counter */
unsigned int sdio_irqs;
struct task_struct *sdio_irq_thread;
atomic_t sdio_irq_thread_abort;
mmc_pm_flag_t pm_flags; /* requested pm features */
#ifdef CONFIG_LEDS_TRIGGERS
struct led_trigger *led; /* activity led */
#endif
#ifdef CONFIG_REGULATOR
bool regulator_enabled; /* regulator state */
#endif
struct dentry *debugfs_root;
struct mmc_async_req *areq; /* active async req */
#ifdef CONFIG_FAIL_MMC_REQUEST
struct fault_attr fail_mmc_request;
#endif
unsigned long private[0] ____cacheline_aligned;
};
extern struct mmc_host *mmc_alloc_host(int extra, struct device *);
extern int mmc_add_host(struct mmc_host *);
extern void mmc_remove_host(struct mmc_host *);
extern void mmc_free_host(struct mmc_host *);
static inline void *mmc_priv(struct mmc_host *host)
{
return (void *)host->private;
}
#define mmc_host_is_spi(host) ((host)->caps & MMC_CAP_SPI)
#define mmc_dev(x) ((x)->parent)
#define mmc_classdev(x) (&(x)->class_dev)
#define mmc_hostname(x) (dev_name(&(x)->class_dev))
extern int mmc_suspend_host(struct mmc_host *);
extern int mmc_resume_host(struct mmc_host *);
extern int mmc_power_save_host(struct mmc_host *host);
extern int mmc_power_restore_host(struct mmc_host *host);
extern void mmc_detect_change(struct mmc_host *, unsigned long delay);
extern void mmc_request_done(struct mmc_host *, struct mmc_request *);
static inline void mmc_signal_sdio_irq(struct mmc_host *host)
{
host->ops->enable_sdio_irq(host, 0);
wake_up_process(host->sdio_irq_thread);
}
struct regulator;
#ifdef CONFIG_REGULATOR
int mmc_regulator_get_ocrmask(struct regulator *supply);
int mmc_regulator_set_ocr(struct mmc_host *mmc,
struct regulator *supply,
unsigned short vdd_bit);
#else
static inline int mmc_regulator_get_ocrmask(struct regulator *supply)
{
return 0;
}
static inline int mmc_regulator_set_ocr(struct mmc_host *mmc,
struct regulator *supply,
unsigned short vdd_bit)
{
return 0;
}
#endif
int mmc_card_awake(struct mmc_host *host);
int mmc_card_sleep(struct mmc_host *host);
int mmc_card_can_sleep(struct mmc_host *host);
int mmc_host_enable(struct mmc_host *host);
int mmc_host_disable(struct mmc_host *host);
int mmc_host_lazy_disable(struct mmc_host *host);
int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *);
static inline void mmc_set_disable_delay(struct mmc_host *host,
unsigned int disable_delay)
{
host->disable_delay = disable_delay;
}
/* Module parameter */
extern int mmc_assume_removable;
static inline int mmc_card_is_removable(struct mmc_host *host)
{
return !(host->caps & MMC_CAP_NONREMOVABLE) && mmc_assume_removable;
}
static inline int mmc_card_keep_power(struct mmc_host *host)
{
return host->pm_flags & MMC_PM_KEEP_POWER;
}
static inline int mmc_card_wake_sdio_irq(struct mmc_host *host)
{
return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ;
}
static inline int mmc_host_cmd23(struct mmc_host *host)
{
return host->caps & MMC_CAP_CMD23;
}
static inline int mmc_boot_partition_access(struct mmc_host *host)
{
return !(host->caps2 & MMC_CAP2_BOOTPART_NOACC);
}
#endif /* LINUX_MMC_HOST_H */
Reference in New Issue View Git Blame Copy Permalink