kernel-ark/drivers/pci/Makefile
Chris Wright c70e0d9dfe PCI: pci-stub module to reserve pci device
When doing device assignment with KVM there's currently nothing to
protect the device from having a driver in the host as well as the guest.
This trivial module just binds the pci device on the host to a stub
driver so that a real host driver can't bind to the device.  It has no
pci id table, it supports only dynamic ids.

 # echo "8086 10f5" > /sys/bus/pci/drivers/pci-stub/new_id
 # echo -n 0000:00:19.0 > /sys/bus/pci/drivers/e1000e/unbind
 # echo -n 0000:00:19.0 > /sys/bus/pci/drivers/pci-stub/bind
 # ls -l /sys/bus/pci/devices/0000:00:19.0/driver
 lrwxrwxrwx 1 root root 0 2008-11-25 19:10 /sys/bus/pci/devices/0000:00:19.0/driver -> ../../../bus/pci/drivers/pci-stub

Cc: "Kay, Allen M" <allen.m.kay@intel.com>
Cc: "Nakajima, Jun" <jun.nakajima@intel.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:12:38 -08:00

61 lines
1.5 KiB
Makefile

#
# Makefile for the PCI bus specific drivers.
#
obj-y += access.o bus.o probe.o remove.o pci.o quirks.o slot.o \
pci-driver.o search.o pci-sysfs.o rom.o setup-res.o \
irq.o
obj-$(CONFIG_PROC_FS) += proc.o
# Build PCI Express stuff if needed
obj-$(CONFIG_PCIEPORTBUS) += pcie/
obj-$(CONFIG_HOTPLUG) += hotplug.o
# Build the PCI Hotplug drivers if we were asked to
obj-$(CONFIG_HOTPLUG_PCI) += hotplug/
ifdef CONFIG_HOTPLUG_PCI
obj-y += hotplug-pci.o
endif
# Build the PCI MSI interrupt support
obj-$(CONFIG_PCI_MSI) += msi.o
# Build the Hypertransport interrupt support
obj-$(CONFIG_HT_IRQ) += htirq.o
# Build Intel IOMMU support
obj-$(CONFIG_DMAR) += dmar.o iova.o intel-iommu.o
obj-$(CONFIG_INTR_REMAP) += dmar.o intr_remapping.o
#
# Some architectures use the generic PCI setup functions
#
obj-$(CONFIG_X86) += setup-bus.o
obj-$(CONFIG_ALPHA) += setup-bus.o setup-irq.o
obj-$(CONFIG_ARM) += setup-bus.o setup-irq.o
obj-$(CONFIG_PARISC) += setup-bus.o
obj-$(CONFIG_SUPERH) += setup-bus.o setup-irq.o
obj-$(CONFIG_PPC32) += setup-irq.o
obj-$(CONFIG_PPC) += setup-bus.o
obj-$(CONFIG_MIPS) += setup-bus.o setup-irq.o
obj-$(CONFIG_X86_VISWS) += setup-irq.o
obj-$(CONFIG_MN10300) += setup-bus.o
#
# ACPI Related PCI FW Functions
#
obj-$(CONFIG_ACPI) += pci-acpi.o
# Cardbus & CompactPCI use setup-bus
obj-$(CONFIG_HOTPLUG) += setup-bus.o
obj-$(CONFIG_PCI_SYSCALL) += syscall.o
obj-$(CONFIG_PCI_STUB) += pci-stub.o
ifeq ($(CONFIG_PCI_DEBUG),y)
EXTRA_CFLAGS += -DDEBUG
endif