kernel-ark/drivers/parisc/eisa.c
Tim Schmielau cd354f1ae7 [PATCH] remove many unneeded #includes of sched.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:54 -08:00

464 lines
12 KiB
C

/*
* eisa.c - provide support for EISA adapters in PA-RISC machines
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*
* Copyright (c) 2001 Matthew Wilcox for Hewlett Packard
* Copyright (c) 2001 Daniel Engstrom <5116@telia.com>
*
* There are two distinct EISA adapters. Mongoose is found in machines
* before the 712; then the Wax ASIC is used. To complicate matters, the
* Wax ASIC also includes a PS/2 and RS-232 controller, but those are
* dealt with elsewhere; this file is concerned only with the EISA portions
* of Wax.
*
*
* HINT:
* -----
* To allow an ISA card to work properly in the EISA slot you need to
* set an edge trigger level. This may be done on the palo command line
* by adding the kernel parameter "eisa_irq_edge=n,n2,[...]]", with
* n and n2 as the irq levels you want to use.
*
* Example: "eisa_irq_edge=10,11" allows ISA cards to operate at
* irq levels 10 and 11.
*/
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/spinlock.h>
#include <linux/eisa.h>
#include <asm/byteorder.h>
#include <asm/io.h>
#include <asm/hardware.h>
#include <asm/processor.h>
#include <asm/parisc-device.h>
#include <asm/delay.h>
#include <asm/eisa_bus.h>
#include <asm/eisa_eeprom.h>
#if 0
#define EISA_DBG(msg, arg... ) printk(KERN_DEBUG "eisa: " msg , ## arg )
#else
#define EISA_DBG(msg, arg... )
#endif
#define SNAKES_EEPROM_BASE_ADDR 0xF0810400
#define MIRAGE_EEPROM_BASE_ADDR 0xF00C0400
static DEFINE_SPINLOCK(eisa_irq_lock);
void __iomem *eisa_eeprom_addr __read_mostly;
/* We can only have one EISA adapter in the system because neither
* implementation can be flexed.
*/
static struct eisa_ba {
struct pci_hba_data hba;
unsigned long eeprom_addr;
struct eisa_root_device root;
} eisa_dev;
/* Port ops */
static inline unsigned long eisa_permute(unsigned short port)
{
if (port & 0x300) {
return 0xfc000000 | ((port & 0xfc00) >> 6)
| ((port & 0x3f8) << 9) | (port & 7);
} else {
return 0xfc000000 | port;
}
}
unsigned char eisa_in8(unsigned short port)
{
if (EISA_bus)
return gsc_readb(eisa_permute(port));
return 0xff;
}
unsigned short eisa_in16(unsigned short port)
{
if (EISA_bus)
return le16_to_cpu(gsc_readw(eisa_permute(port)));
return 0xffff;
}
unsigned int eisa_in32(unsigned short port)
{
if (EISA_bus)
return le32_to_cpu(gsc_readl(eisa_permute(port)));
return 0xffffffff;
}
void eisa_out8(unsigned char data, unsigned short port)
{
if (EISA_bus)
gsc_writeb(data, eisa_permute(port));
}
void eisa_out16(unsigned short data, unsigned short port)
{
if (EISA_bus)
gsc_writew(cpu_to_le16(data), eisa_permute(port));
}
void eisa_out32(unsigned int data, unsigned short port)
{
if (EISA_bus)
gsc_writel(cpu_to_le32(data), eisa_permute(port));
}
#ifndef CONFIG_PCI
/* We call these directly without PCI. See asm/io.h. */
EXPORT_SYMBOL(eisa_in8);
EXPORT_SYMBOL(eisa_in16);
EXPORT_SYMBOL(eisa_in32);
EXPORT_SYMBOL(eisa_out8);
EXPORT_SYMBOL(eisa_out16);
EXPORT_SYMBOL(eisa_out32);
#endif
/* Interrupt handling */
/* cached interrupt mask registers */
static int master_mask;
static int slave_mask;
/* the trig level can be set with the
* eisa_irq_edge=n,n,n commandline parameter
* We should really read this from the EEPROM
* in the furure.
*/
/* irq 13,8,2,1,0 must be edge */
static unsigned int eisa_irq_level __read_mostly; /* default to edge triggered */
/* called by free irq */
static void eisa_disable_irq(unsigned int irq)
{
unsigned long flags;
EISA_DBG("disable irq %d\n", irq);
/* just mask for now */
spin_lock_irqsave(&eisa_irq_lock, flags);
if (irq & 8) {
slave_mask |= (1 << (irq&7));
eisa_out8(slave_mask, 0xa1);
} else {
master_mask |= (1 << (irq&7));
eisa_out8(master_mask, 0x21);
}
spin_unlock_irqrestore(&eisa_irq_lock, flags);
EISA_DBG("pic0 mask %02x\n", eisa_in8(0x21));
EISA_DBG("pic1 mask %02x\n", eisa_in8(0xa1));
}
/* called by request irq */
static void eisa_enable_irq(unsigned int irq)
{
unsigned long flags;
EISA_DBG("enable irq %d\n", irq);
spin_lock_irqsave(&eisa_irq_lock, flags);
if (irq & 8) {
slave_mask &= ~(1 << (irq&7));
eisa_out8(slave_mask, 0xa1);
} else {
master_mask &= ~(1 << (irq&7));
eisa_out8(master_mask, 0x21);
}
spin_unlock_irqrestore(&eisa_irq_lock, flags);
EISA_DBG("pic0 mask %02x\n", eisa_in8(0x21));
EISA_DBG("pic1 mask %02x\n", eisa_in8(0xa1));
}
static unsigned int eisa_startup_irq(unsigned int irq)
{
eisa_enable_irq(irq);
return 0;
}
static struct hw_interrupt_type eisa_interrupt_type = {
.typename = "EISA",
.startup = eisa_startup_irq,
.shutdown = eisa_disable_irq,
.enable = eisa_enable_irq,
.disable = eisa_disable_irq,
.ack = no_ack_irq,
.end = no_end_irq,
};
static irqreturn_t eisa_irq(int wax_irq, void *intr_dev)
{
int irq = gsc_readb(0xfc01f000); /* EISA supports 16 irqs */
unsigned long flags;
spin_lock_irqsave(&eisa_irq_lock, flags);
/* read IRR command */
eisa_out8(0x0a, 0x20);
eisa_out8(0x0a, 0xa0);
EISA_DBG("irq IAR %02x 8259-1 irr %02x 8259-2 irr %02x\n",
irq, eisa_in8(0x20), eisa_in8(0xa0));
/* read ISR command */
eisa_out8(0x0a, 0x20);
eisa_out8(0x0a, 0xa0);
EISA_DBG("irq 8259-1 isr %02x imr %02x 8259-2 isr %02x imr %02x\n",
eisa_in8(0x20), eisa_in8(0x21), eisa_in8(0xa0), eisa_in8(0xa1));
irq &= 0xf;
/* mask irq and write eoi */
if (irq & 8) {
slave_mask |= (1 << (irq&7));
eisa_out8(slave_mask, 0xa1);
eisa_out8(0x60 | (irq&7),0xa0);/* 'Specific EOI' to slave */
eisa_out8(0x62,0x20); /* 'Specific EOI' to master-IRQ2 */
} else {
master_mask |= (1 << (irq&7));
eisa_out8(master_mask, 0x21);
eisa_out8(0x60|irq,0x20); /* 'Specific EOI' to master */
}
spin_unlock_irqrestore(&eisa_irq_lock, flags);
__do_IRQ(irq);
spin_lock_irqsave(&eisa_irq_lock, flags);
/* unmask */
if (irq & 8) {
slave_mask &= ~(1 << (irq&7));
eisa_out8(slave_mask, 0xa1);
} else {
master_mask &= ~(1 << (irq&7));
eisa_out8(master_mask, 0x21);
}
spin_unlock_irqrestore(&eisa_irq_lock, flags);
return IRQ_HANDLED;
}
static irqreturn_t dummy_irq2_handler(int _, void *dev)
{
printk(KERN_ALERT "eisa: uhh, irq2?\n");
return IRQ_HANDLED;
}
static struct irqaction irq2_action = {
.handler = dummy_irq2_handler,
.name = "cascade",
};
static void init_eisa_pic(void)
{
unsigned long flags;
spin_lock_irqsave(&eisa_irq_lock, flags);
eisa_out8(0xff, 0x21); /* mask during init */
eisa_out8(0xff, 0xa1); /* mask during init */
/* master pic */
eisa_out8(0x11,0x20); /* ICW1 */
eisa_out8(0x00,0x21); /* ICW2 */
eisa_out8(0x04,0x21); /* ICW3 */
eisa_out8(0x01,0x21); /* ICW4 */
eisa_out8(0x40,0x20); /* OCW2 */
/* slave pic */
eisa_out8(0x11,0xa0); /* ICW1 */
eisa_out8(0x08,0xa1); /* ICW2 */
eisa_out8(0x02,0xa1); /* ICW3 */
eisa_out8(0x01,0xa1); /* ICW4 */
eisa_out8(0x40,0xa0); /* OCW2 */
udelay(100);
slave_mask = 0xff;
master_mask = 0xfb;
eisa_out8(slave_mask, 0xa1); /* OCW1 */
eisa_out8(master_mask, 0x21); /* OCW1 */
/* setup trig level */
EISA_DBG("EISA edge/level %04x\n", eisa_irq_level);
eisa_out8(eisa_irq_level&0xff, 0x4d0); /* Set all irq's to edge */
eisa_out8((eisa_irq_level >> 8) & 0xff, 0x4d1);
EISA_DBG("pic0 mask %02x\n", eisa_in8(0x21));
EISA_DBG("pic1 mask %02x\n", eisa_in8(0xa1));
EISA_DBG("pic0 edge/level %02x\n", eisa_in8(0x4d0));
EISA_DBG("pic1 edge/level %02x\n", eisa_in8(0x4d1));
spin_unlock_irqrestore(&eisa_irq_lock, flags);
}
/* Device initialisation */
#define is_mongoose(dev) (dev->id.sversion == 0x00076)
static int __devinit eisa_probe(struct parisc_device *dev)
{
int i, result;
char *name = is_mongoose(dev) ? "Mongoose" : "Wax";
printk(KERN_INFO "%s EISA Adapter found at 0x%08lx\n",
name, dev->hpa.start);
eisa_dev.hba.dev = dev;
eisa_dev.hba.iommu = ccio_get_iommu(dev);
eisa_dev.hba.lmmio_space.name = "EISA";
eisa_dev.hba.lmmio_space.start = F_EXTEND(0xfc000000);
eisa_dev.hba.lmmio_space.end = F_EXTEND(0xffbfffff);
eisa_dev.hba.lmmio_space.flags = IORESOURCE_MEM;
result = ccio_request_resource(dev, &eisa_dev.hba.lmmio_space);
if (result < 0) {
printk(KERN_ERR "EISA: failed to claim EISA Bus address space!\n");
return result;
}
eisa_dev.hba.io_space.name = "EISA";
eisa_dev.hba.io_space.start = 0;
eisa_dev.hba.io_space.end = 0xffff;
eisa_dev.hba.lmmio_space.flags = IORESOURCE_IO;
result = request_resource(&ioport_resource, &eisa_dev.hba.io_space);
if (result < 0) {
printk(KERN_ERR "EISA: failed to claim EISA Bus port space!\n");
return result;
}
pcibios_register_hba(&eisa_dev.hba);
result = request_irq(dev->irq, eisa_irq, IRQF_SHARED, "EISA", &eisa_dev);
if (result) {
printk(KERN_ERR "EISA: request_irq failed!\n");
return result;
}
/* Reserve IRQ2 */
irq_desc[2].action = &irq2_action;
for (i = 0; i < 16; i++) {
irq_desc[i].chip = &eisa_interrupt_type;
}
EISA_bus = 1;
if (dev->num_addrs) {
/* newer firmware hand out the eeprom address */
eisa_dev.eeprom_addr = dev->addr[0];
} else {
/* old firmware, need to figure out the box */
if (is_mongoose(dev)) {
eisa_dev.eeprom_addr = SNAKES_EEPROM_BASE_ADDR;
} else {
eisa_dev.eeprom_addr = MIRAGE_EEPROM_BASE_ADDR;
}
}
eisa_eeprom_addr = ioremap_nocache(eisa_dev.eeprom_addr, HPEE_MAX_LENGTH);
result = eisa_enumerator(eisa_dev.eeprom_addr, &eisa_dev.hba.io_space,
&eisa_dev.hba.lmmio_space);
init_eisa_pic();
if (result >= 0) {
/* FIXME : Don't enumerate the bus twice. */
eisa_dev.root.dev = &dev->dev;
dev->dev.driver_data = &eisa_dev.root;
eisa_dev.root.bus_base_addr = 0;
eisa_dev.root.res = &eisa_dev.hba.io_space;
eisa_dev.root.slots = result;
eisa_dev.root.dma_mask = 0xffffffff; /* wild guess */
if (eisa_root_register (&eisa_dev.root)) {
printk(KERN_ERR "EISA: Failed to register EISA root\n");
return -1;
}
}
return 0;
}
static struct parisc_device_id eisa_tbl[] = {
{ HPHW_BA, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00076 }, /* Mongoose */
{ HPHW_BA, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00090 }, /* Wax EISA */
{ 0, }
};
MODULE_DEVICE_TABLE(parisc, eisa_tbl);
static struct parisc_driver eisa_driver = {
.name = "eisa_ba",
.id_table = eisa_tbl,
.probe = eisa_probe,
};
void __init eisa_init(void)
{
register_parisc_driver(&eisa_driver);
}
static unsigned int eisa_irq_configured;
void eisa_make_irq_level(int num)
{
if (eisa_irq_configured& (1<<num)) {
printk(KERN_WARNING
"IRQ %d polarity configured twice (last to level)\n",
num);
}
eisa_irq_level |= (1<<num); /* set the corresponding bit */
eisa_irq_configured |= (1<<num); /* set the corresponding bit */
}
void eisa_make_irq_edge(int num)
{
if (eisa_irq_configured& (1<<num)) {
printk(KERN_WARNING
"IRQ %d polarity configured twice (last to edge)\n",
num);
}
eisa_irq_level &= ~(1<<num); /* clear the corresponding bit */
eisa_irq_configured |= (1<<num); /* set the corresponding bit */
}
static int __init eisa_irq_setup(char *str)
{
char *cur = str;
int val;
EISA_DBG("IRQ setup\n");
while (cur != NULL) {
char *pe;
val = (int) simple_strtoul(cur, &pe, 0);
if (val > 15 || val < 0) {
printk(KERN_ERR "eisa: EISA irq value are 0-15\n");
continue;
}
if (val == 2) {
val = 9;
}
eisa_make_irq_edge(val); /* clear the corresponding bit */
EISA_DBG("setting IRQ %d to edge-triggered mode\n", val);
if ((cur = strchr(cur, ','))) {
cur++;
} else {
break;
}
}
return 1;
}
__setup("eisa_irq_edge=", eisa_irq_setup);