a982ac06b0
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4. Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
184 lines
6.8 KiB
Plaintext
184 lines
6.8 KiB
Plaintext
xpad - Linux USB driver for X-Box gamepads
|
|
|
|
This is the very first release of a driver for X-Box gamepads.
|
|
Basically, this was hacked away in just a few hours, so don't expect
|
|
miracles.
|
|
|
|
In particular, there is currently NO support for the rumble pack.
|
|
You won't find many ff-aware linux applications anyway.
|
|
|
|
|
|
0. Notes
|
|
--------
|
|
|
|
Driver updated for kernel 2.6.17.11. (Based on a patch for 2.6.11.4.)
|
|
|
|
The number of buttons/axes reported varies based on 3 things:
|
|
- if you are using a known controller
|
|
- if you are using a known dance pad
|
|
- if using an unknown device (one not listed below), what you set in the
|
|
module configuration for "Map D-PAD to buttons rather than axes for unknown
|
|
pads" (module option dpad_to_buttons)
|
|
|
|
If you set dpad_to_buttons to 0 and you are using an unknown device (one
|
|
not listed below), the driver will map the directional pad to axes (X/Y),
|
|
if you said N it will map the d-pad to buttons, which is needed for dance
|
|
style games to function correctly. The default is Y.
|
|
|
|
dpad_to_buttons has no effect for known pads.
|
|
|
|
0.1 Normal Controllers
|
|
----------------------
|
|
With a normal controller, the directional pad is mapped to its own X/Y axes.
|
|
The jstest-program from joystick-1.2.15 (jstest-version 2.1.0) will report 8
|
|
axes and 10 buttons.
|
|
|
|
All 8 axes work, though they all have the same range (-32768..32767)
|
|
and the zero-setting is not correct for the triggers (I don't know if that
|
|
is some limitation of jstest, since the input device setup should be fine. I
|
|
didn't have a look at jstest itself yet).
|
|
|
|
All of the 10 buttons work (in digital mode). The six buttons on the
|
|
right side (A, B, X, Y, black, white) are said to be "analog" and
|
|
report their values as 8 bit unsigned, not sure what this is good for.
|
|
|
|
I tested the controller with quake3, and configuration and
|
|
in game functionality were OK. However, I find it rather difficult to
|
|
play first person shooters with a pad. Your mileage may vary.
|
|
|
|
|
|
0.2 Xbox Dance Pads
|
|
-------------------
|
|
When using a known dance pad, jstest will report 6 axes and 14 buttons.
|
|
|
|
For dance style pads (like the redoctane pad) several changes
|
|
have been made. The old driver would map the d-pad to axes, resulting
|
|
in the driver being unable to report when the user was pressing both
|
|
left+right or up+down, making DDR style games unplayable.
|
|
|
|
Known dance pads automatically map the d-pad to buttons and will work
|
|
correctly out of the box.
|
|
|
|
If your dance pad is recognized by the driver but is using axes instead
|
|
of buttons, see section 0.3 - Unknown Controllers
|
|
|
|
I've tested this with Stepmania, and it works quite well.
|
|
|
|
|
|
0.3 Unknown Controllers
|
|
----------------------
|
|
If you have an unknown xbox controller, it should work just fine with
|
|
the default settings.
|
|
|
|
HOWEVER if you have an unknown dance pad not listed below, it will not
|
|
work UNLESS you set "dpad_to_buttons" to 1 in the module configuration.
|
|
|
|
PLEASE, if you have an unknown controller, email Dom <binary1230@yahoo.com> with
|
|
a dump from /proc/bus/usb and a description of the pad (manufacturer, country,
|
|
whether it is a dance pad or normal controller) so that we can add your pad
|
|
to the list of supported devices, ensuring that it will work out of the
|
|
box in the future.
|
|
|
|
|
|
1. USB adapter
|
|
--------------
|
|
|
|
Before you can actually use the driver, you need to get yourself an
|
|
adapter cable to connect the X-Box controller to your Linux-Box. You
|
|
can buy these online fairly cheap, or build your own.
|
|
|
|
Such a cable is pretty easy to build. The Controller itself is a USB
|
|
compound device (a hub with three ports for two expansion slots and
|
|
the controller device) with the only difference in a nonstandard connector
|
|
(5 pins vs. 4 on standard USB connector).
|
|
|
|
You just need to solder a USB connector onto the cable and keep the
|
|
yellow wire unconnected. The other pins have the same order on both
|
|
connectors so there is no magic to it. Detailed info on these matters
|
|
can be found on the net ([1], [2], [3]).
|
|
|
|
Thanks to the trip splitter found on the cable you don't even need to cut the
|
|
original one. You can buy an extension cable and cut that instead. That way,
|
|
you can still use the controller with your X-Box, if you have one ;)
|
|
|
|
|
|
2. Driver Installation
|
|
----------------------
|
|
|
|
Once you have the adapter cable and the controller is connected, you need
|
|
to load your USB subsystem and should cat /proc/bus/usb/devices.
|
|
There should be an entry like the one at the end [4].
|
|
|
|
Currently (as of version 0.0.6), the following devices are included:
|
|
original Microsoft XBOX controller (US), vendor=0x045e, product=0x0202
|
|
smaller Microsoft XBOX controller (US), vendor=0x045e, product=0x0289
|
|
original Microsoft XBOX controller (Japan), vendor=0x045e, product=0x0285
|
|
InterAct PowerPad Pro (Germany), vendor=0x05fd, product=0x107a
|
|
RedOctane Xbox Dance Pad (US), vendor=0x0c12, product=0x8809
|
|
|
|
The driver should work with xbox pads not listed above as well, however
|
|
you will need to do something extra for dance pads to work.
|
|
|
|
If you have a controller not listed above, see 0.3 - Unknown Controllers
|
|
|
|
If you compiled and installed the driver, test the functionality:
|
|
> modprobe xpad
|
|
> modprobe joydev
|
|
> jstest /dev/js0
|
|
|
|
If you're using a normal controller, there should be a single line showing
|
|
18 inputs (8 axes, 10 buttons), and its values should change if you move
|
|
the sticks and push the buttons. If you're using a dance pad, it should
|
|
show 20 inputs (6 axes, 14 buttons).
|
|
|
|
It works? Voila, you're done ;)
|
|
|
|
|
|
3. Thanks
|
|
---------
|
|
|
|
I have to thank ITO Takayuki for the detailed info on his site
|
|
http://euc.jp/periphs/xbox-controller.ja.html.
|
|
|
|
His useful info and both the usb-skeleton as well as the iforce input driver
|
|
(Greg Kroah-Hartmann; Vojtech Pavlik) helped a lot in rapid prototyping
|
|
the basic functionality.
|
|
|
|
|
|
4. References
|
|
-------------
|
|
|
|
1. http://euc.jp/periphs/xbox-controller.ja.html (ITO Takayuki)
|
|
2. http://xpad.xbox-scene.com/
|
|
3. http://www.xboxhackz.com/Hackz-Reference.htm
|
|
|
|
4. /proc/bus/usb/devices - dump from InterAct PowerPad Pro (Germany):
|
|
|
|
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
|
|
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=32 #Cfgs= 1
|
|
P: Vendor=05fd ProdID=107a Rev= 1.00
|
|
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
|
|
I: If#= 0 Alt= 0 #EPs= 2 Cls=58(unk. ) Sub=42 Prot=00 Driver=(none)
|
|
E: Ad=81(I) Atr=03(Int.) MxPS= 32 Ivl= 10ms
|
|
E: Ad=02(O) Atr=03(Int.) MxPS= 32 Ivl= 10ms
|
|
|
|
5. /proc/bus/usb/devices - dump from Redoctane Xbox Dance Pad (US):
|
|
|
|
T: Bus=01 Lev=02 Prnt=09 Port=00 Cnt=01 Dev#= 10 Spd=12 MxCh= 0
|
|
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
|
|
P: Vendor=0c12 ProdID=8809 Rev= 0.01
|
|
S: Product=XBOX DDR
|
|
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
|
|
I: If#= 0 Alt= 0 #EPs= 2 Cls=58(unk. ) Sub=42 Prot=00 Driver=xpad
|
|
E: Ad=82(I) Atr=03(Int.) MxPS= 32 Ivl=4ms
|
|
E: Ad=02(O) Atr=03(Int.) MxPS= 32 Ivl=4ms
|
|
|
|
--
|
|
Marko Friedemann <mfr@bmx-chemnitz.de>
|
|
2002-07-16
|
|
- original doc
|
|
|
|
Dominic Cerquetti <binary1230@yahoo.com>
|
|
2005-03-19
|
|
- added stuff for dance pads, new d-pad->axes mappings
|