kernel-ark/drivers/scsi/ahci.c
Martin Wilck c0b34ad295 [PATCH] Fix HD activity LED with ahci
Patch: fix wrong HD activity control by ahci driver

The ahci driver 1.0 sets the SActive bit on every transaction,
causing the LED to light up. The SActive bit is used only for
native command queuing (NCQ) which the current driver version
doesn't implement. Resetting the SActive bit is the device's
responsibility (by sending a "Set Device Bits FIS" to the
host adapter) but this is not required in response to
non-NCQ commands, and (most) devices don't. Thus the LED
stays always on. This patch fixes the LED behavior.

Spec references:
http://www.intel.com/technology/serialata/pdf/rev1_1.pdf, sec. 3.3.13, 5.5.1
http://www.serialata.org/docs/serialata10a.pdf
http://www.intel.com/design/storage/papers/25266401.pdf

Signed-off-by: Martin.Wilck@fujitsu-siemens.com
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-08-23 01:03:39 -04:00

1110 lines
28 KiB
C

/*
* ahci.c - AHCI SATA support
*
* Copyright 2004 Red Hat, Inc.
*
* The contents of this file are subject to the Open
* Software License version 1.1 that can be found at
* http://www.opensource.org/licenses/osl-1.1.txt and is included herein
* by reference.
*
* Alternatively, the contents of this file may be used under the terms
* of the GNU General Public License version 2 (the "GPL") as distributed
* in the kernel source COPYING file, in which case the provisions of
* the GPL are applicable instead of the above. If you wish to allow
* the use of your version of this file only under the terms of the
* GPL and not to allow others to use your version of this file under
* the OSL, indicate your decision by deleting the provisions above and
* replace them with the notice and other provisions required by the GPL.
* If you do not delete the provisions above, a recipient may use your
* version of this file under either the OSL or the GPL.
*
* Version 1.0 of the AHCI specification:
* http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/dma-mapping.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <asm/io.h>
#define DRV_NAME "ahci"
#define DRV_VERSION "1.01"
enum {
AHCI_PCI_BAR = 5,
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
AHCI_USE_CLUSTERING = 0,
AHCI_CMD_SLOT_SZ = 32 * 32,
AHCI_RX_FIS_SZ = 256,
AHCI_CMD_TBL_HDR = 0x80,
AHCI_CMD_TBL_CDB = 0x40,
AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR + (AHCI_MAX_SG * 16),
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_SZ +
AHCI_RX_FIS_SZ,
AHCI_IRQ_ON_SG = (1 << 31),
AHCI_CMD_ATAPI = (1 << 5),
AHCI_CMD_WRITE = (1 << 6),
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
board_ahci = 0,
/* global controller registers */
HOST_CAP = 0x00, /* host capabilities */
HOST_CTL = 0x04, /* global host control */
HOST_IRQ_STAT = 0x08, /* interrupt status */
HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
/* HOST_CTL bits */
HOST_RESET = (1 << 0), /* reset controller; self-clear */
HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */
PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */
PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */
PORT_IRQ_STAT = 0x10, /* interrupt status */
PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */
PORT_CMD = 0x18, /* port command */
PORT_TFDATA = 0x20, /* taskfile data */
PORT_SIG = 0x24, /* device TF signature */
PORT_CMD_ISSUE = 0x38, /* command issue */
PORT_SCR = 0x28, /* SATA phy register block */
PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */
PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */
PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */
PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
PORT_IRQ_FATAL = PORT_IRQ_TF_ERR |
PORT_IRQ_HBUS_ERR |
PORT_IRQ_HBUS_DATA_ERR |
PORT_IRQ_IF_ERR,
DEF_PORT_IRQ = PORT_IRQ_FATAL | PORT_IRQ_PHYRDY |
PORT_IRQ_CONNECT | PORT_IRQ_SG_DONE |
PORT_IRQ_UNK_FIS | PORT_IRQ_SDB_FIS |
PORT_IRQ_DMAS_FIS | PORT_IRQ_PIOS_FIS |
PORT_IRQ_D2H_REG_FIS,
/* PORT_CMD bits */
PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
/* hpriv->flags bits */
AHCI_FLAG_MSI = (1 << 0),
};
struct ahci_cmd_hdr {
u32 opts;
u32 status;
u32 tbl_addr;
u32 tbl_addr_hi;
u32 reserved[4];
};
struct ahci_sg {
u32 addr;
u32 addr_hi;
u32 reserved;
u32 flags_size;
};
struct ahci_host_priv {
unsigned long flags;
u32 cap; /* cache of HOST_CAP register */
u32 port_map; /* cache of HOST_PORTS_IMPL reg */
};
struct ahci_port_priv {
struct ahci_cmd_hdr *cmd_slot;
dma_addr_t cmd_slot_dma;
void *cmd_tbl;
dma_addr_t cmd_tbl_dma;
struct ahci_sg *cmd_tbl_sg;
void *rx_fis;
dma_addr_t rx_fis_dma;
};
static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static int ahci_qc_issue(struct ata_queued_cmd *qc);
static irqreturn_t ahci_interrupt (int irq, void *dev_instance, struct pt_regs *regs);
static void ahci_phy_reset(struct ata_port *ap);
static void ahci_irq_clear(struct ata_port *ap);
static void ahci_eng_timeout(struct ata_port *ap);
static int ahci_port_start(struct ata_port *ap);
static void ahci_port_stop(struct ata_port *ap);
static void ahci_host_stop(struct ata_host_set *host_set);
static void ahci_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
static void ahci_qc_prep(struct ata_queued_cmd *qc);
static u8 ahci_check_status(struct ata_port *ap);
static u8 ahci_check_err(struct ata_port *ap);
static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
static void ahci_remove_one (struct pci_dev *pdev);
static Scsi_Host_Template ahci_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.eh_strategy_handler = ata_scsi_error,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = AHCI_MAX_SG,
.max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = AHCI_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = AHCI_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
.ordered_flush = 1,
};
static struct ata_port_operations ahci_ops = {
.port_disable = ata_port_disable,
.check_status = ahci_check_status,
.check_altstatus = ahci_check_status,
.check_err = ahci_check_err,
.dev_select = ata_noop_dev_select,
.tf_read = ahci_tf_read,
.phy_reset = ahci_phy_reset,
.qc_prep = ahci_qc_prep,
.qc_issue = ahci_qc_issue,
.eng_timeout = ahci_eng_timeout,
.irq_handler = ahci_interrupt,
.irq_clear = ahci_irq_clear,
.scr_read = ahci_scr_read,
.scr_write = ahci_scr_write,
.port_start = ahci_port_start,
.port_stop = ahci_port_stop,
.host_stop = ahci_host_stop,
};
static struct ata_port_info ahci_port_info[] = {
/* board_ahci */
{
.sht = &ahci_sht,
.host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
ATA_FLAG_PIO_DMA,
.pio_mask = 0x03, /* pio3-4 */
.udma_mask = 0x7f, /* udma0-6 ; FIXME */
.port_ops = &ahci_ops,
},
};
static struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VENDOR_ID_INTEL, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH6 */
{ PCI_VENDOR_ID_INTEL, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH6M */
{ PCI_VENDOR_ID_INTEL, 0x27c1, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH7 */
{ PCI_VENDOR_ID_INTEL, 0x27c5, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH7M */
{ PCI_VENDOR_ID_INTEL, 0x27c3, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH7R */
{ PCI_VENDOR_ID_AL, 0x5288, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ULi M5288 */
{ PCI_VENDOR_ID_INTEL, 0x2681, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ESB2 */
{ PCI_VENDOR_ID_INTEL, 0x2682, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ESB2 */
{ PCI_VENDOR_ID_INTEL, 0x2683, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ESB2 */
{ PCI_VENDOR_ID_INTEL, 0x27c6, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ICH7-M DH */
{ } /* terminate list */
};
static struct pci_driver ahci_pci_driver = {
.name = DRV_NAME,
.id_table = ahci_pci_tbl,
.probe = ahci_init_one,
.remove = ahci_remove_one,
};
static inline unsigned long ahci_port_base_ul (unsigned long base, unsigned int port)
{
return base + 0x100 + (port * 0x80);
}
static inline void *ahci_port_base (void *base, unsigned int port)
{
return (void *) ahci_port_base_ul((unsigned long)base, port);
}
static void ahci_host_stop(struct ata_host_set *host_set)
{
struct ahci_host_priv *hpriv = host_set->private_data;
kfree(hpriv);
ata_host_stop(host_set);
}
static int ahci_port_start(struct ata_port *ap)
{
struct device *dev = ap->host_set->dev;
struct ahci_host_priv *hpriv = ap->host_set->private_data;
struct ahci_port_priv *pp;
void *mem, *mmio = ap->host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
dma_addr_t mem_dma;
pp = kmalloc(sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
memset(pp, 0, sizeof(*pp));
mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL);
if (!mem) {
kfree(pp);
return -ENOMEM;
}
memset(mem, 0, AHCI_PORT_PRIV_DMA_SZ);
/*
* First item in chunk of DMA memory: 32-slot command table,
* 32 bytes each in size
*/
pp->cmd_slot = mem;
pp->cmd_slot_dma = mem_dma;
mem += AHCI_CMD_SLOT_SZ;
mem_dma += AHCI_CMD_SLOT_SZ;
/*
* Second item: Received-FIS area
*/
pp->rx_fis = mem;
pp->rx_fis_dma = mem_dma;
mem += AHCI_RX_FIS_SZ;
mem_dma += AHCI_RX_FIS_SZ;
/*
* Third item: data area for storing a single command
* and its scatter-gather table
*/
pp->cmd_tbl = mem;
pp->cmd_tbl_dma = mem_dma;
pp->cmd_tbl_sg = mem + AHCI_CMD_TBL_HDR;
ap->private_data = pp;
if (hpriv->cap & HOST_CAP_64)
writel((pp->cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI);
writel(pp->cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
readl(port_mmio + PORT_LST_ADDR); /* flush */
if (hpriv->cap & HOST_CAP_64)
writel((pp->rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI);
writel(pp->rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
readl(port_mmio + PORT_FIS_ADDR); /* flush */
writel(PORT_CMD_ICC_ACTIVE | PORT_CMD_FIS_RX |
PORT_CMD_POWER_ON | PORT_CMD_SPIN_UP |
PORT_CMD_START, port_mmio + PORT_CMD);
readl(port_mmio + PORT_CMD); /* flush */
return 0;
}
static void ahci_port_stop(struct ata_port *ap)
{
struct device *dev = ap->host_set->dev;
struct ahci_port_priv *pp = ap->private_data;
void *mmio = ap->host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
u32 tmp;
tmp = readl(port_mmio + PORT_CMD);
tmp &= ~(PORT_CMD_START | PORT_CMD_FIS_RX);
writel(tmp, port_mmio + PORT_CMD);
readl(port_mmio + PORT_CMD); /* flush */
/* spec says 500 msecs for each PORT_CMD_{START,FIS_RX} bit, so
* this is slightly incorrect.
*/
msleep(500);
ap->private_data = NULL;
dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
pp->cmd_slot, pp->cmd_slot_dma);
kfree(pp);
}
static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg_in)
{
unsigned int sc_reg;
switch (sc_reg_in) {
case SCR_STATUS: sc_reg = 0; break;
case SCR_CONTROL: sc_reg = 1; break;
case SCR_ERROR: sc_reg = 2; break;
case SCR_ACTIVE: sc_reg = 3; break;
default:
return 0xffffffffU;
}
return readl((void *) ap->ioaddr.scr_addr + (sc_reg * 4));
}
static void ahci_scr_write (struct ata_port *ap, unsigned int sc_reg_in,
u32 val)
{
unsigned int sc_reg;
switch (sc_reg_in) {
case SCR_STATUS: sc_reg = 0; break;
case SCR_CONTROL: sc_reg = 1; break;
case SCR_ERROR: sc_reg = 2; break;
case SCR_ACTIVE: sc_reg = 3; break;
default:
return;
}
writel(val, (void *) ap->ioaddr.scr_addr + (sc_reg * 4));
}
static void ahci_phy_reset(struct ata_port *ap)
{
void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
struct ata_taskfile tf;
struct ata_device *dev = &ap->device[0];
u32 tmp;
__sata_phy_reset(ap);
if (ap->flags & ATA_FLAG_PORT_DISABLED)
return;
tmp = readl(port_mmio + PORT_SIG);
tf.lbah = (tmp >> 24) & 0xff;
tf.lbam = (tmp >> 16) & 0xff;
tf.lbal = (tmp >> 8) & 0xff;
tf.nsect = (tmp) & 0xff;
dev->class = ata_dev_classify(&tf);
if (!ata_dev_present(dev))
ata_port_disable(ap);
}
static u8 ahci_check_status(struct ata_port *ap)
{
void *mmio = (void *) ap->ioaddr.cmd_addr;
return readl(mmio + PORT_TFDATA) & 0xFF;
}
static u8 ahci_check_err(struct ata_port *ap)
{
void *mmio = (void *) ap->ioaddr.cmd_addr;
return (readl(mmio + PORT_TFDATA) >> 8) & 0xFF;
}
static void ahci_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
struct ahci_port_priv *pp = ap->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
ata_tf_from_fis(d2h_fis, tf);
}
static void ahci_fill_sg(struct ata_queued_cmd *qc)
{
struct ahci_port_priv *pp = qc->ap->private_data;
unsigned int i;
VPRINTK("ENTER\n");
/*
* Next, the S/G list.
*/
for (i = 0; i < qc->n_elem; i++) {
u32 sg_len;
dma_addr_t addr;
addr = sg_dma_address(&qc->sg[i]);
sg_len = sg_dma_len(&qc->sg[i]);
pp->cmd_tbl_sg[i].addr = cpu_to_le32(addr & 0xffffffff);
pp->cmd_tbl_sg[i].addr_hi = cpu_to_le32((addr >> 16) >> 16);
pp->cmd_tbl_sg[i].flags_size = cpu_to_le32(sg_len - 1);
}
}
static void ahci_qc_prep(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ahci_port_priv *pp = ap->private_data;
u32 opts;
const u32 cmd_fis_len = 5; /* five dwords */
/*
* Fill in command slot information (currently only one slot,
* slot 0, is currently since we don't do queueing)
*/
opts = (qc->n_elem << 16) | cmd_fis_len;
if (qc->tf.flags & ATA_TFLAG_WRITE)
opts |= AHCI_CMD_WRITE;
if (is_atapi_taskfile(&qc->tf))
opts |= AHCI_CMD_ATAPI;
pp->cmd_slot[0].opts = cpu_to_le32(opts);
pp->cmd_slot[0].status = 0;
pp->cmd_slot[0].tbl_addr = cpu_to_le32(pp->cmd_tbl_dma & 0xffffffff);
pp->cmd_slot[0].tbl_addr_hi = cpu_to_le32((pp->cmd_tbl_dma >> 16) >> 16);
/*
* Fill in command table information. First, the header,
* a SATA Register - Host to Device command FIS.
*/
ata_tf_to_fis(&qc->tf, pp->cmd_tbl, 0);
if (opts & AHCI_CMD_ATAPI) {
memset(pp->cmd_tbl + AHCI_CMD_TBL_CDB, 0, 32);
memcpy(pp->cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb, ap->cdb_len);
}
if (!(qc->flags & ATA_QCFLAG_DMAMAP))
return;
ahci_fill_sg(qc);
}
static void ahci_intr_error(struct ata_port *ap, u32 irq_stat)
{
void *mmio = ap->host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
u32 tmp;
int work;
/* stop DMA */
tmp = readl(port_mmio + PORT_CMD);
tmp &= ~PORT_CMD_START;
writel(tmp, port_mmio + PORT_CMD);
/* wait for engine to stop. TODO: this could be
* as long as 500 msec
*/
work = 1000;
while (work-- > 0) {
tmp = readl(port_mmio + PORT_CMD);
if ((tmp & PORT_CMD_LIST_ON) == 0)
break;
udelay(10);
}
/* clear SATA phy error, if any */
tmp = readl(port_mmio + PORT_SCR_ERR);
writel(tmp, port_mmio + PORT_SCR_ERR);
/* if DRQ/BSY is set, device needs to be reset.
* if so, issue COMRESET
*/
tmp = readl(port_mmio + PORT_TFDATA);
if (tmp & (ATA_BUSY | ATA_DRQ)) {
writel(0x301, port_mmio + PORT_SCR_CTL);
readl(port_mmio + PORT_SCR_CTL); /* flush */
udelay(10);
writel(0x300, port_mmio + PORT_SCR_CTL);
readl(port_mmio + PORT_SCR_CTL); /* flush */
}
/* re-start DMA */
tmp = readl(port_mmio + PORT_CMD);
tmp |= PORT_CMD_START;
writel(tmp, port_mmio + PORT_CMD);
readl(port_mmio + PORT_CMD); /* flush */
printk(KERN_WARNING "ata%u: error occurred, port reset\n", ap->id);
}
static void ahci_eng_timeout(struct ata_port *ap)
{
void *mmio = ap->host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
struct ata_queued_cmd *qc;
DPRINTK("ENTER\n");
ahci_intr_error(ap, readl(port_mmio + PORT_IRQ_STAT));
qc = ata_qc_from_tag(ap, ap->active_tag);
if (!qc) {
printk(KERN_ERR "ata%u: BUG: timeout without command\n",
ap->id);
} else {
/* hack alert! We cannot use the supplied completion
* function from inside the ->eh_strategy_handler() thread.
* libata is the only user of ->eh_strategy_handler() in
* any kernel, so the default scsi_done() assumes it is
* not being called from the SCSI EH.
*/
qc->scsidone = scsi_finish_command;
ata_qc_complete(qc, ATA_ERR);
}
}
static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
{
void *mmio = ap->host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
u32 status, serr, ci;
serr = readl(port_mmio + PORT_SCR_ERR);
writel(serr, port_mmio + PORT_SCR_ERR);
status = readl(port_mmio + PORT_IRQ_STAT);
writel(status, port_mmio + PORT_IRQ_STAT);
ci = readl(port_mmio + PORT_CMD_ISSUE);
if (likely((ci & 0x1) == 0)) {
if (qc) {
ata_qc_complete(qc, 0);
qc = NULL;
}
}
if (status & PORT_IRQ_FATAL) {
ahci_intr_error(ap, status);
if (qc)
ata_qc_complete(qc, ATA_ERR);
}
return 1;
}
static void ahci_irq_clear(struct ata_port *ap)
{
/* TODO */
}
static irqreturn_t ahci_interrupt (int irq, void *dev_instance, struct pt_regs *regs)
{
struct ata_host_set *host_set = dev_instance;
struct ahci_host_priv *hpriv;
unsigned int i, handled = 0;
void *mmio;
u32 irq_stat, irq_ack = 0;
VPRINTK("ENTER\n");
hpriv = host_set->private_data;
mmio = host_set->mmio_base;
/* sigh. 0xffffffff is a valid return from h/w */
irq_stat = readl(mmio + HOST_IRQ_STAT);
irq_stat &= hpriv->port_map;
if (!irq_stat)
return IRQ_NONE;
spin_lock(&host_set->lock);
for (i = 0; i < host_set->n_ports; i++) {
struct ata_port *ap;
u32 tmp;
VPRINTK("port %u\n", i);
ap = host_set->ports[i];
tmp = irq_stat & (1 << i);
if (tmp && ap) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
if (ahci_host_intr(ap, qc))
irq_ack |= (1 << i);
}
}
if (irq_ack) {
writel(irq_ack, mmio + HOST_IRQ_STAT);
handled = 1;
}
spin_unlock(&host_set->lock);
VPRINTK("EXIT\n");
return IRQ_RETVAL(handled);
}
static int ahci_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
void *port_mmio = (void *) ap->ioaddr.cmd_addr;
writel(1, port_mmio + PORT_CMD_ISSUE);
readl(port_mmio + PORT_CMD_ISSUE); /* flush */
return 0;
}
static void ahci_setup_port(struct ata_ioports *port, unsigned long base,
unsigned int port_idx)
{
VPRINTK("ENTER, base==0x%lx, port_idx %u\n", base, port_idx);
base = ahci_port_base_ul(base, port_idx);
VPRINTK("base now==0x%lx\n", base);
port->cmd_addr = base;
port->scr_addr = base + PORT_SCR;
VPRINTK("EXIT\n");
}
static int ahci_host_init(struct ata_probe_ent *probe_ent)
{
struct ahci_host_priv *hpriv = probe_ent->private_data;
struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
void __iomem *mmio = probe_ent->mmio_base;
u32 tmp, cap_save;
u16 tmp16;
unsigned int i, j, using_dac;
int rc;
void __iomem *port_mmio;
cap_save = readl(mmio + HOST_CAP);
cap_save &= ( (1<<28) | (1<<17) );
cap_save |= (1 << 27);
/* global controller reset */
tmp = readl(mmio + HOST_CTL);
if ((tmp & HOST_RESET) == 0) {
writel(tmp | HOST_RESET, mmio + HOST_CTL);
readl(mmio + HOST_CTL); /* flush */
}
/* reset must complete within 1 second, or
* the hardware should be considered fried.
*/
ssleep(1);
tmp = readl(mmio + HOST_CTL);
if (tmp & HOST_RESET) {
printk(KERN_ERR DRV_NAME "(%s): controller reset failed (0x%x)\n",
pci_name(pdev), tmp);
return -EIO;
}
writel(HOST_AHCI_EN, mmio + HOST_CTL);
(void) readl(mmio + HOST_CTL); /* flush */
writel(cap_save, mmio + HOST_CAP);
writel(0xf, mmio + HOST_PORTS_IMPL);
(void) readl(mmio + HOST_PORTS_IMPL); /* flush */
pci_read_config_word(pdev, 0x92, &tmp16);
tmp16 |= 0xf;
pci_write_config_word(pdev, 0x92, tmp16);
hpriv->cap = readl(mmio + HOST_CAP);
hpriv->port_map = readl(mmio + HOST_PORTS_IMPL);
probe_ent->n_ports = (hpriv->cap & 0x1f) + 1;
VPRINTK("cap 0x%x port_map 0x%x n_ports %d\n",
hpriv->cap, hpriv->port_map, probe_ent->n_ports);
using_dac = hpriv->cap & HOST_CAP_64;
if (using_dac &&
!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
if (rc) {
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
printk(KERN_ERR DRV_NAME "(%s): 64-bit DMA enable failed\n",
pci_name(pdev));
return rc;
}
}
} else {
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
printk(KERN_ERR DRV_NAME "(%s): 32-bit DMA enable failed\n",
pci_name(pdev));
return rc;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
printk(KERN_ERR DRV_NAME "(%s): 32-bit consistent DMA enable failed\n",
pci_name(pdev));
return rc;
}
}
for (i = 0; i < probe_ent->n_ports; i++) {
#if 0 /* BIOSen initialize this incorrectly */
if (!(hpriv->port_map & (1 << i)))
continue;
#endif
port_mmio = ahci_port_base(mmio, i);
VPRINTK("mmio %p port_mmio %p\n", mmio, port_mmio);
ahci_setup_port(&probe_ent->port[i],
(unsigned long) mmio, i);
/* make sure port is not active */
tmp = readl(port_mmio + PORT_CMD);
VPRINTK("PORT_CMD 0x%x\n", tmp);
if (tmp & (PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
PORT_CMD_FIS_RX | PORT_CMD_START)) {
tmp &= ~(PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
PORT_CMD_FIS_RX | PORT_CMD_START);
writel(tmp, port_mmio + PORT_CMD);
readl(port_mmio + PORT_CMD); /* flush */
/* spec says 500 msecs for each bit, so
* this is slightly incorrect.
*/
msleep(500);
}
writel(PORT_CMD_SPIN_UP, port_mmio + PORT_CMD);
j = 0;
while (j < 100) {
msleep(10);
tmp = readl(port_mmio + PORT_SCR_STAT);
if ((tmp & 0xf) == 0x3)
break;
j++;
}
tmp = readl(port_mmio + PORT_SCR_ERR);
VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
writel(tmp, port_mmio + PORT_SCR_ERR);
/* ack any pending irq events for this port */
tmp = readl(port_mmio + PORT_IRQ_STAT);
VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
if (tmp)
writel(tmp, port_mmio + PORT_IRQ_STAT);
writel(1 << i, mmio + HOST_IRQ_STAT);
/* set irq mask (enables interrupts) */
writel(DEF_PORT_IRQ, port_mmio + PORT_IRQ_MASK);
}
tmp = readl(mmio + HOST_CTL);
VPRINTK("HOST_CTL 0x%x\n", tmp);
writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
tmp = readl(mmio + HOST_CTL);
VPRINTK("HOST_CTL 0x%x\n", tmp);
pci_set_master(pdev);
return 0;
}
/* move to PCI layer, integrate w/ MSI stuff */
static void pci_intx(struct pci_dev *pdev, int enable)
{
u16 pci_command, new;
pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
if (enable)
new = pci_command & ~PCI_COMMAND_INTX_DISABLE;
else
new = pci_command | PCI_COMMAND_INTX_DISABLE;
if (new != pci_command)
pci_write_config_word(pdev, PCI_COMMAND, pci_command);
}
static void ahci_print_info(struct ata_probe_ent *probe_ent)
{
struct ahci_host_priv *hpriv = probe_ent->private_data;
struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
void *mmio = probe_ent->mmio_base;
u32 vers, cap, impl, speed;
const char *speed_s;
u16 cc;
const char *scc_s;
vers = readl(mmio + HOST_VERSION);
cap = hpriv->cap;
impl = hpriv->port_map;
speed = (cap >> 20) & 0xf;
if (speed == 1)
speed_s = "1.5";
else if (speed == 2)
speed_s = "3";
else
speed_s = "?";
pci_read_config_word(pdev, 0x0a, &cc);
if (cc == 0x0101)
scc_s = "IDE";
else if (cc == 0x0106)
scc_s = "SATA";
else if (cc == 0x0104)
scc_s = "RAID";
else
scc_s = "unknown";
printk(KERN_INFO DRV_NAME "(%s) AHCI %02x%02x.%02x%02x "
"%u slots %u ports %s Gbps 0x%x impl %s mode\n"
,
pci_name(pdev),
(vers >> 24) & 0xff,
(vers >> 16) & 0xff,
(vers >> 8) & 0xff,
vers & 0xff,
((cap >> 8) & 0x1f) + 1,
(cap & 0x1f) + 1,
speed_s,
impl,
scc_s);
printk(KERN_INFO DRV_NAME "(%s) flags: "
"%s%s%s%s%s%s"
"%s%s%s%s%s%s%s\n"
,
pci_name(pdev),
cap & (1 << 31) ? "64bit " : "",
cap & (1 << 30) ? "ncq " : "",
cap & (1 << 28) ? "ilck " : "",
cap & (1 << 27) ? "stag " : "",
cap & (1 << 26) ? "pm " : "",
cap & (1 << 25) ? "led " : "",
cap & (1 << 24) ? "clo " : "",
cap & (1 << 19) ? "nz " : "",
cap & (1 << 18) ? "only " : "",
cap & (1 << 17) ? "pmp " : "",
cap & (1 << 15) ? "pio " : "",
cap & (1 << 14) ? "slum " : "",
cap & (1 << 13) ? "part " : ""
);
}
static int ahci_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
struct ata_probe_ent *probe_ent = NULL;
struct ahci_host_priv *hpriv;
unsigned long base;
void *mmio_base;
unsigned int board_idx = (unsigned int) ent->driver_data;
int have_msi, pci_dev_busy = 0;
int rc;
VPRINTK("ENTER\n");
if (!printed_version++)
printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
return rc;
rc = pci_request_regions(pdev, DRV_NAME);
if (rc) {
pci_dev_busy = 1;
goto err_out;
}
if (pci_enable_msi(pdev) == 0)
have_msi = 1;
else {
pci_intx(pdev, 1);
have_msi = 0;
}
probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
if (probe_ent == NULL) {
rc = -ENOMEM;
goto err_out_msi;
}
memset(probe_ent, 0, sizeof(*probe_ent));
probe_ent->dev = pci_dev_to_dev(pdev);
INIT_LIST_HEAD(&probe_ent->node);
mmio_base = ioremap(pci_resource_start(pdev, AHCI_PCI_BAR),
pci_resource_len(pdev, AHCI_PCI_BAR));
if (mmio_base == NULL) {
rc = -ENOMEM;
goto err_out_free_ent;
}
base = (unsigned long) mmio_base;
hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL);
if (!hpriv) {
rc = -ENOMEM;
goto err_out_iounmap;
}
memset(hpriv, 0, sizeof(*hpriv));
probe_ent->sht = ahci_port_info[board_idx].sht;
probe_ent->host_flags = ahci_port_info[board_idx].host_flags;
probe_ent->pio_mask = ahci_port_info[board_idx].pio_mask;
probe_ent->udma_mask = ahci_port_info[board_idx].udma_mask;
probe_ent->port_ops = ahci_port_info[board_idx].port_ops;
probe_ent->irq = pdev->irq;
probe_ent->irq_flags = SA_SHIRQ;
probe_ent->mmio_base = mmio_base;
probe_ent->private_data = hpriv;
if (have_msi)
hpriv->flags |= AHCI_FLAG_MSI;
/* initialize adapter */
rc = ahci_host_init(probe_ent);
if (rc)
goto err_out_hpriv;
ahci_print_info(probe_ent);
/* FIXME: check ata_device_add return value */
ata_device_add(probe_ent);
kfree(probe_ent);
return 0;
err_out_hpriv:
kfree(hpriv);
err_out_iounmap:
iounmap(mmio_base);
err_out_free_ent:
kfree(probe_ent);
err_out_msi:
if (have_msi)
pci_disable_msi(pdev);
else
pci_intx(pdev, 0);
pci_release_regions(pdev);
err_out:
if (!pci_dev_busy)
pci_disable_device(pdev);
return rc;
}
static void ahci_remove_one (struct pci_dev *pdev)
{
struct device *dev = pci_dev_to_dev(pdev);
struct ata_host_set *host_set = dev_get_drvdata(dev);
struct ahci_host_priv *hpriv = host_set->private_data;
struct ata_port *ap;
unsigned int i;
int have_msi;
for (i = 0; i < host_set->n_ports; i++) {
ap = host_set->ports[i];
scsi_remove_host(ap->host);
}
have_msi = hpriv->flags & AHCI_FLAG_MSI;
free_irq(host_set->irq, host_set);
for (i = 0; i < host_set->n_ports; i++) {
ap = host_set->ports[i];
ata_scsi_release(ap->host);
scsi_host_put(ap->host);
}
host_set->ops->host_stop(host_set);
kfree(host_set);
if (have_msi)
pci_disable_msi(pdev);
else
pci_intx(pdev, 0);
pci_release_regions(pdev);
pci_disable_device(pdev);
dev_set_drvdata(dev, NULL);
}
static int __init ahci_init(void)
{
return pci_module_init(&ahci_pci_driver);
}
static void __exit ahci_exit(void)
{
pci_unregister_driver(&ahci_pci_driver);
}
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("AHCI SATA low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, ahci_pci_tbl);
module_init(ahci_init);
module_exit(ahci_exit);