kernel-ark/include/asm-mips/serial.h
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

445 lines
17 KiB
C

/*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 1999 by Ralf Baechle
* Copyright (C) 1999, 2000 Silicon Graphics, Inc.
*/
#ifndef _ASM_SERIAL_H
#define _ASM_SERIAL_H
#include <linux/config.h>
/*
* This assumes you have a 1.8432 MHz clock for your UART.
*
* It'd be nice if someone built a serial card with a 24.576 MHz
* clock, since the 16550A is capable of handling a top speed of 1.5
* megabits/second; but this requires the faster clock.
*/
#define BASE_BAUD (1843200 / 16)
/* Standard COM flags (except for COM4, because of the 8514 problem) */
#ifdef CONFIG_SERIAL_DETECT_IRQ
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
#define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
#else
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
#ifdef CONFIG_SERIAL_MANY_PORTS
#define FOURPORT_FLAGS ASYNC_FOURPORT
#define ACCENT_FLAGS 0
#define BOCA_FLAGS 0
#define HUB6_FLAGS 0
#define RS_TABLE_SIZE 64
#else
#define RS_TABLE_SIZE
#endif
/*
* The following define the access methods for the HUB6 card. All
* access is through two ports for all 24 possible chips. The card is
* selected through the high 2 bits, the port on that card with the
* "middle" 3 bits, and the register on that port with the bottom
* 3 bits.
*
* While the access port and interrupt is configurable, the default
* port locations are 0x302 for the port control register, and 0x303
* for the data read/write register. Normally, the interrupt is at irq3
* but can be anything from 3 to 7 inclusive. Note that using 3 will
* require disabling com2.
*/
#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
#ifdef CONFIG_MACH_JAZZ
#include <asm/jazz.h>
#ifndef CONFIG_OLIVETTI_M700
/* Some Jazz machines seem to have an 8MHz crystal clock but I don't know
exactly which ones ... XXX */
#define JAZZ_BASE_BAUD ( 8000000 / 16 ) /* ( 3072000 / 16) */
#else
/* but the M700 isn't such a strange beast */
#define JAZZ_BASE_BAUD BASE_BAUD
#endif
#define _JAZZ_SERIAL_INIT(int, base) \
{ .baud_base = JAZZ_BASE_BAUD, .irq = int, .flags = STD_COM_FLAGS, \
.iomem_base = (u8 *) base, .iomem_reg_shift = 0, \
.io_type = SERIAL_IO_MEM }
#define JAZZ_SERIAL_PORT_DEFNS \
_JAZZ_SERIAL_INIT(JAZZ_SERIAL1_IRQ, JAZZ_SERIAL1_BASE), \
_JAZZ_SERIAL_INIT(JAZZ_SERIAL2_IRQ, JAZZ_SERIAL2_BASE),
#else
#define JAZZ_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_MIPS_COBALT
#include <asm/cobalt/cobalt.h>
#define COBALT_BASE_BAUD (18432000 / 16)
#define COBALT_SERIAL_PORT_DEFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, COBALT_BASE_BAUD, 0xc800000, COBALT_SERIAL_IRQ, STD_COM_FLAGS }, /* ttyS0 */
#else
#define COBALT_SERIAL_PORT_DEFNS
#endif
/*
* Both Galileo boards have the same UART mappings.
*/
#if defined (CONFIG_MIPS_EV96100) || defined (CONFIG_MIPS_EV64120)
#include <asm/galileo-boards/ev96100.h>
#include <asm/galileo-boards/ev96100int.h>
#define EV96100_SERIAL_PORT_DEFNS \
{ .baud_base = EV96100_BASE_BAUD, .irq = EV96100INT_UART_0, \
.flags = STD_COM_FLAGS, \
.iomem_base = EV96100_UART0_REGS_BASE, .iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM }, \
{ .baud_base = EV96100_BASE_BAUD, .irq = EV96100INT_UART_0, \
.flags = STD_COM_FLAGS, \
.iomem_base = EV96100_UART1_REGS_BASE, .iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM },
#else
#define EV96100_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_MIPS_ITE8172
#include <asm/it8172/it8172.h>
#include <asm/it8172/it8172_int.h>
#include <asm/it8712.h>
#define ITE_SERIAL_PORT_DEFNS \
{ .baud_base = BASE_BAUD, .port = (IT8172_PCI_IO_BASE + IT_UART_BASE), \
.irq = IT8172_UART_IRQ, .flags = STD_COM_FLAGS, .type = 0x3 }, \
{ .baud_base = (24000000/(16*13)), .port = (IT8172_PCI_IO_BASE + IT8712_UART1_PORT), \
.irq = IT8172_SERIRQ_4, .flags = STD_COM_FLAGS, .type = 0x3 }, \
/* Smart Card Reader 0 */ \
{ .baud_base = BASE_BAUD, .port = (IT8172_PCI_IO_BASE + IT_SCR0_BASE), \
.irq = IT8172_SCR0_IRQ, .flags = STD_COM_FLAGS, .type = 0x3 }, \
/* Smart Card Reader 1 */ \
{ .baud_base = BASE_BAUD, .port = (IT8172_PCI_IO_BASE + IT_SCR1_BASE), \
.irq = IT8172_SCR1_IRQ, .flags = STD_COM_FLAGS, .type = 0x3 },
#else
#define ITE_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_MIPS_IVR
#include <asm/it8172/it8172.h>
#include <asm/it8172/it8172_int.h>
#define IVR_SERIAL_PORT_DEFNS \
{ .baud_base = BASE_BAUD, .port = (IT8172_PCI_IO_BASE + IT_UART_BASE), \
.irq = IT8172_UART_IRQ, .flags = STD_COM_FLAGS, .type = 0x3 }, \
/* Smart Card Reader 1 */ \
{ .baud_base = BASE_BAUD, .port = (IT8172_PCI_IO_BASE + IT_SCR1_BASE), \
.irq = IT8172_SCR1_IRQ, .flags = STD_COM_FLAGS, .type = 0x3 },
#else
#define IVR_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_TOSHIBA_JMR3927
#include <asm/jmr3927/jmr3927.h>
#define TXX927_SERIAL_PORT_DEFNS \
{ .baud_base = JMR3927_BASE_BAUD, .port = UART0_ADDR, .irq = UART0_INT, \
.flags = UART0_FLAGS, .type = 1 }, \
{ .baud_base = JMR3927_BASE_BAUD, .port = UART1_ADDR, .irq = UART1_INT, \
.flags = UART1_FLAGS, .type = 1 },
#else
#define TXX927_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_SERIAL_AU1X00
#include <asm/mach-au1x00/au1000.h>
#ifdef CONFIG_SOC_AU1000
#define AU1000_SERIAL_PORT_DEFNS \
{ .baud_base = 0, .port = UART0_ADDR, \
.iomem_base = (unsigned char *)UART0_ADDR, \
.irq = AU1000_UART0_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART1_ADDR, \
.iomem_base = (unsigned char *)UART1_ADDR, \
.irq = AU1000_UART1_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART2_ADDR, \
.iomem_base = (unsigned char *)UART2_ADDR, \
.irq = AU1000_UART2_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART3_ADDR, \
.iomem_base = (unsigned char *)UART3_ADDR, \
.irq = AU1000_UART3_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 },
#endif
#ifdef CONFIG_SOC_AU1500
#define AU1000_SERIAL_PORT_DEFNS \
{ .baud_base = 0, .port = UART0_ADDR, \
.iomem_base = (unsigned char *)UART0_ADDR, \
.irq = AU1500_UART0_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART3_ADDR, \
.iomem_base = (unsigned char *)UART3_ADDR, \
.irq = AU1500_UART3_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 },
#endif
#ifdef CONFIG_SOC_AU1100
#define AU1000_SERIAL_PORT_DEFNS \
{ .baud_base = 0, .port = UART0_ADDR, \
.iomem_base = (unsigned char *)UART0_ADDR, \
.irq = AU1100_UART0_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART1_ADDR, \
.iomem_base = (unsigned char *)UART1_ADDR, \
.irq = AU1100_UART1_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART3_ADDR, \
.iomem_base = (unsigned char *)UART3_ADDR, \
.irq = AU1100_UART3_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 },
#endif
#ifdef CONFIG_SOC_AU1550
#define AU1000_SERIAL_PORT_DEFNS \
{ .baud_base = 0, .port = UART0_ADDR, \
.iomem_base = (unsigned char *)UART0_ADDR, \
.irq = AU1550_UART0_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART1_ADDR, \
.iomem_base = (unsigned char *)UART1_ADDR, \
.irq = AU1550_UART1_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART3_ADDR, \
.iomem_base = (unsigned char *)UART3_ADDR, \
.irq = AU1550_UART3_INT, .flags = STD_COM_FLAGS,\
.iomem_reg_shift = 2 },
#endif
#ifdef CONFIG_SOC_AU1200
#define AU1000_SERIAL_PORT_DEFNS \
{ .baud_base = 0, .port = UART0_ADDR, \
.iomem_base = (unsigned char *)UART0_ADDR, \
.irq = AU1200_UART0_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 }, \
{ .baud_base = 0, .port = UART1_ADDR, \
.iomem_base = (unsigned char *)UART1_ADDR, \
.irq = AU1200_UART1_INT, .flags = STD_COM_FLAGS, \
.iomem_reg_shift = 2 },
#endif
#else
#define AU1000_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_HAVE_STD_PC_SERIAL_PORT
#define STD_SERIAL_PORT_DEFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
#ifdef CONFIG_SERIAL_MANY_PORTS
#define EXTRA_SERIAL_PORT_DEFNS \
{ 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
{ 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
{ 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
{ 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
{ 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
{ 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
{ 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
{ 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
{ 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
{ 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
{ 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
{ 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
{ 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
{ 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
{ 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
{ 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
{ 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
{ 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
{ 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
{ 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
{ 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
{ 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
{ 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
{ 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
{ 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
{ 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
{ 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
{ 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
#else /* CONFIG_SERIAL_MANY_PORTS */
#define EXTRA_SERIAL_PORT_DEFNS
#endif /* CONFIG_SERIAL_MANY_PORTS */
#else /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */
#define STD_SERIAL_PORT_DEFNS
#define EXTRA_SERIAL_PORT_DEFNS
#endif /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */
/* You can have up to four HUB6's in the system, but I've only
* included two cards here for a total of twelve ports.
*/
#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
#define HUB6_SERIAL_PORT_DFNS \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
{ 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
#else
#define HUB6_SERIAL_PORT_DFNS
#endif
#ifdef CONFIG_MOMENCO_JAGUAR_ATX
/* Ordinary NS16552 duart with a 20MHz crystal. */
#define JAGUAR_ATX_UART_CLK 20000000
#define JAGUAR_ATX_BASE_BAUD (JAGUAR_ATX_UART_CLK / 16)
#define JAGUAR_ATX_SERIAL1_IRQ 6
#define JAGUAR_ATX_SERIAL1_BASE 0xfd000023L
#define _JAGUAR_ATX_SERIAL_INIT(int, base) \
{ baud_base: JAGUAR_ATX_BASE_BAUD, irq: int, \
flags: (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \
iomem_base: (u8 *) base, iomem_reg_shift: 2, \
io_type: SERIAL_IO_MEM }
#define MOMENCO_JAGUAR_ATX_SERIAL_PORT_DEFNS \
_JAGUAR_ATX_SERIAL_INIT(JAGUAR_ATX_SERIAL1_IRQ, JAGUAR_ATX_SERIAL1_BASE)
#else
#define MOMENCO_JAGUAR_ATX_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_MOMENCO_OCELOT_3
#define OCELOT_3_BASE_BAUD ( 20000000 / 16 )
#define OCELOT_3_SERIAL_IRQ 6
#define OCELOT_3_SERIAL_BASE (signed)0xfd000020
#define _OCELOT_3_SERIAL_INIT(int, base) \
{ baud_base: OCELOT_3_BASE_BAUD, irq: int, \
flags: STD_COM_FLAGS, \
iomem_base: (u8 *) base, iomem_reg_shift: 2, \
io_type: SERIAL_IO_MEM }
#define MOMENCO_OCELOT_3_SERIAL_PORT_DEFNS \
_OCELOT_3_SERIAL_INIT(OCELOT_3_SERIAL_IRQ, OCELOT_3_SERIAL_BASE)
#else
#define MOMENCO_OCELOT_3_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_MOMENCO_OCELOT
/* Ordinary NS16552 duart with a 20MHz crystal. */
#define OCELOT_BASE_BAUD ( 20000000 / 16 )
#define OCELOT_SERIAL1_IRQ 4
#define OCELOT_SERIAL1_BASE 0xe0001020
#define _OCELOT_SERIAL_INIT(int, base) \
{ .baud_base = OCELOT_BASE_BAUD, .irq = int, .flags = STD_COM_FLAGS, \
.iomem_base = (u8 *) base, .iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM }
#define MOMENCO_OCELOT_SERIAL_PORT_DEFNS \
_OCELOT_SERIAL_INIT(OCELOT_SERIAL1_IRQ, OCELOT_SERIAL1_BASE)
#else
#define MOMENCO_OCELOT_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_MOMENCO_OCELOT_G
/* Ordinary NS16552 duart with a 20MHz crystal. */
#define OCELOT_G_BASE_BAUD ( 20000000 / 16 )
#define OCELOT_G_SERIAL1_IRQ 4
#if 0
#define OCELOT_G_SERIAL1_BASE 0xe0001020
#else
#define OCELOT_G_SERIAL1_BASE 0xfd000020
#endif
#define _OCELOT_G_SERIAL_INIT(int, base) \
{ .baud_base = OCELOT_G_BASE_BAUD, .irq = int, .flags = STD_COM_FLAGS,\
.iomem_base = (u8 *) base, .iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM }
#define MOMENCO_OCELOT_G_SERIAL_PORT_DEFNS \
_OCELOT_G_SERIAL_INIT(OCELOT_G_SERIAL1_IRQ, OCELOT_G_SERIAL1_BASE)
#else
#define MOMENCO_OCELOT_G_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_MOMENCO_OCELOT_C
/* Ordinary NS16552 duart with a 20MHz crystal. */
#define OCELOT_C_BASE_BAUD ( 20000000 / 16 )
#define OCELOT_C_SERIAL1_IRQ 80
#define OCELOT_C_SERIAL1_BASE 0xfd000020
#define OCELOT_C_SERIAL2_IRQ 81
#define OCELOT_C_SERIAL2_BASE 0xfd000000
#define _OCELOT_C_SERIAL_INIT(int, base) \
{ .baud_base = OCELOT_C_BASE_BAUD, \
.irq = (int), \
.flags = STD_COM_FLAGS, \
.iomem_base = (u8 *) base, \
.iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM \
}
#define MOMENCO_OCELOT_C_SERIAL_PORT_DEFNS \
_OCELOT_C_SERIAL_INIT(OCELOT_C_SERIAL1_IRQ, OCELOT_C_SERIAL1_BASE), \
_OCELOT_C_SERIAL_INIT(OCELOT_C_SERIAL2_IRQ, OCELOT_C_SERIAL2_BASE)
#else
#define MOMENCO_OCELOT_C_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_DDB5477
#include <asm/ddb5xxx/ddb5477.h>
#define DDB5477_SERIAL_PORT_DEFNS \
{ .baud_base = BASE_BAUD, .irq = VRC5477_IRQ_UART0, \
.flags = STD_COM_FLAGS, .iomem_base = (u8*)0xbfa04200, \
.iomem_reg_shift = 3, .io_type = SERIAL_IO_MEM}, \
{ .baud_base = BASE_BAUD, .irq = VRC5477_IRQ_UART1, \
.flags = STD_COM_FLAGS, .iomem_base = (u8*)0xbfa04240, \
.iomem_reg_shift = 3, .io_type = SERIAL_IO_MEM},
#else
#define DDB5477_SERIAL_PORT_DEFNS
#endif
#ifdef CONFIG_SGI_IP32
/*
* The IP32 (SGI O2) has standard serial ports (UART 16550A) mapped in memory
* They are initialized in ip32_setup
*/
#define IP32_SERIAL_PORT_DEFNS \
{},{},
#else
#define IP32_SERIAL_PORT_DEFNS
#endif /* CONFIG_SGI_IP32 */
#define SERIAL_PORT_DFNS \
COBALT_SERIAL_PORT_DEFNS \
DDB5477_SERIAL_PORT_DEFNS \
EV96100_SERIAL_PORT_DEFNS \
EXTRA_SERIAL_PORT_DEFNS \
HUB6_SERIAL_PORT_DFNS \
IP32_SERIAL_PORT_DEFNS \
ITE_SERIAL_PORT_DEFNS \
IVR_SERIAL_PORT_DEFNS \
JAZZ_SERIAL_PORT_DEFNS \
STD_SERIAL_PORT_DEFNS \
MOMENCO_OCELOT_G_SERIAL_PORT_DEFNS \
MOMENCO_OCELOT_C_SERIAL_PORT_DEFNS \
MOMENCO_OCELOT_SERIAL_PORT_DEFNS \
MOMENCO_OCELOT_3_SERIAL_PORT_DEFNS \
TXX927_SERIAL_PORT_DEFNS \
AU1000_SERIAL_PORT_DEFNS
#endif /* _ASM_SERIAL_H */