69584bd6d2
The addition of a number to the scan_element names caused an issue in drivers that used either #define or an enum to provide the number. Before this fix names like ADIS16350_ACCEL_X_accel_x_en occur rather than 5_accel_x_en. Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
204 lines
6.5 KiB
C
204 lines
6.5 KiB
C
#ifndef SPI_ADIS16240_H_
|
|
#define SPI_ADIS16240_H_
|
|
|
|
#define ADIS16240_STARTUP_DELAY 220 /* ms */
|
|
|
|
#define ADIS16240_READ_REG(a) a
|
|
#define ADIS16240_WRITE_REG(a) ((a) | 0x80)
|
|
|
|
/* Flash memory write count */
|
|
#define ADIS16240_FLASH_CNT 0x00
|
|
/* Output, power supply */
|
|
#define ADIS16240_SUPPLY_OUT 0x02
|
|
/* Output, x-axis accelerometer */
|
|
#define ADIS16240_XACCL_OUT 0x04
|
|
/* Output, y-axis accelerometer */
|
|
#define ADIS16240_YACCL_OUT 0x06
|
|
/* Output, z-axis accelerometer */
|
|
#define ADIS16240_ZACCL_OUT 0x08
|
|
/* Output, auxiliary ADC input */
|
|
#define ADIS16240_AUX_ADC 0x0A
|
|
/* Output, temperature */
|
|
#define ADIS16240_TEMP_OUT 0x0C
|
|
/* Output, x-axis acceleration peak */
|
|
#define ADIS16240_XPEAK_OUT 0x0E
|
|
/* Output, y-axis acceleration peak */
|
|
#define ADIS16240_YPEAK_OUT 0x10
|
|
/* Output, z-axis acceleration peak */
|
|
#define ADIS16240_ZPEAK_OUT 0x12
|
|
/* Output, sum-of-squares acceleration peak */
|
|
#define ADIS16240_XYZPEAK_OUT 0x14
|
|
/* Output, Capture Buffer 1, X and Y acceleration */
|
|
#define ADIS16240_CAPT_BUF1 0x16
|
|
/* Output, Capture Buffer 2, Z acceleration */
|
|
#define ADIS16240_CAPT_BUF2 0x18
|
|
/* Diagnostic, error flags */
|
|
#define ADIS16240_DIAG_STAT 0x1A
|
|
/* Diagnostic, event counter */
|
|
#define ADIS16240_EVNT_CNTR 0x1C
|
|
/* Diagnostic, check sum value from firmware test */
|
|
#define ADIS16240_CHK_SUM 0x1E
|
|
/* Calibration, x-axis acceleration offset adjustment */
|
|
#define ADIS16240_XACCL_OFF 0x20
|
|
/* Calibration, y-axis acceleration offset adjustment */
|
|
#define ADIS16240_YACCL_OFF 0x22
|
|
/* Calibration, z-axis acceleration offset adjustment */
|
|
#define ADIS16240_ZACCL_OFF 0x24
|
|
/* Clock, hour and minute */
|
|
#define ADIS16240_CLK_TIME 0x2E
|
|
/* Clock, month and day */
|
|
#define ADIS16240_CLK_DATE 0x30
|
|
/* Clock, year */
|
|
#define ADIS16240_CLK_YEAR 0x32
|
|
/* Wake-up setting, hour and minute */
|
|
#define ADIS16240_WAKE_TIME 0x34
|
|
/* Wake-up setting, month and day */
|
|
#define ADIS16240_WAKE_DATE 0x36
|
|
/* Alarm 1 amplitude threshold */
|
|
#define ADIS16240_ALM_MAG1 0x38
|
|
/* Alarm 2 amplitude threshold */
|
|
#define ADIS16240_ALM_MAG2 0x3A
|
|
/* Alarm control */
|
|
#define ADIS16240_ALM_CTRL 0x3C
|
|
/* Capture, external trigger control */
|
|
#define ADIS16240_XTRIG_CTRL 0x3E
|
|
/* Capture, address pointer */
|
|
#define ADIS16240_CAPT_PNTR 0x40
|
|
/* Capture, configuration and control */
|
|
#define ADIS16240_CAPT_CTRL 0x42
|
|
/* General-purpose digital input/output control */
|
|
#define ADIS16240_GPIO_CTRL 0x44
|
|
/* Miscellaneous control */
|
|
#define ADIS16240_MSC_CTRL 0x46
|
|
/* Internal sample period (rate) control */
|
|
#define ADIS16240_SMPL_PRD 0x48
|
|
/* System command */
|
|
#define ADIS16240_GLOB_CMD 0x4A
|
|
|
|
#define ADIS16240_OUTPUTS 6
|
|
|
|
/* MSC_CTRL */
|
|
/* Enables sum-of-squares output (XYZPEAK_OUT) */
|
|
#define ADIS16240_MSC_CTRL_XYZPEAK_OUT_EN (1 << 15)
|
|
/* Enables peak tracking output (XPEAK_OUT, YPEAK_OUT, and ZPEAK_OUT) */
|
|
#define ADIS16240_MSC_CTRL_X_Y_ZPEAK_OUT_EN (1 << 14)
|
|
/* Self-test enable: 1 = apply electrostatic force, 0 = disabled */
|
|
#define ADIS16240_MSC_CTRL_SELF_TEST_EN (1 << 8)
|
|
/* Data-ready enable: 1 = enabled, 0 = disabled */
|
|
#define ADIS16240_MSC_CTRL_DATA_RDY_EN (1 << 2)
|
|
/* Data-ready polarity: 1 = active high, 0 = active low */
|
|
#define ADIS16240_MSC_CTRL_ACTIVE_HIGH (1 << 1)
|
|
/* Data-ready line selection: 1 = DIO2, 0 = DIO1 */
|
|
#define ADIS16240_MSC_CTRL_DATA_RDY_DIO2 (1 << 0)
|
|
|
|
/* DIAG_STAT */
|
|
/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
|
|
#define ADIS16240_DIAG_STAT_ALARM2 (1<<9)
|
|
/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
|
|
#define ADIS16240_DIAG_STAT_ALARM1 (1<<8)
|
|
/* Capture buffer full: 1 = capture buffer is full */
|
|
#define ADIS16240_DIAG_STAT_CPT_BUF_FUL (1<<7)
|
|
/* Flash test, checksum flag: 1 = mismatch, 0 = match */
|
|
#define ADIS16240_DIAG_STAT_CHKSUM (1<<6)
|
|
/* Power-on, self-test flag: 1 = failure, 0 = pass */
|
|
#define ADIS16240_DIAG_STAT_PWRON_FAIL (1<<5)
|
|
/* Power-on self-test: 1 = in-progress, 0 = complete */
|
|
#define ADIS16240_DIAG_STAT_PWRON_BUSY (1<<4)
|
|
/* SPI communications failure */
|
|
#define ADIS16240_DIAG_STAT_SPI_FAIL (1<<3)
|
|
/* Flash update failure */
|
|
#define ADIS16240_DIAG_STAT_FLASH_UPT (1<<2)
|
|
/* Power supply above 3.625 V */
|
|
#define ADIS16240_DIAG_STAT_POWER_HIGH (1<<1)
|
|
/* Power supply below 3.15 V */
|
|
#define ADIS16240_DIAG_STAT_POWER_LOW (1<<0)
|
|
|
|
/* GLOB_CMD */
|
|
#define ADIS16240_GLOB_CMD_RESUME (1<<8)
|
|
#define ADIS16240_GLOB_CMD_SW_RESET (1<<7)
|
|
#define ADIS16240_GLOB_CMD_STANDBY (1<<2)
|
|
|
|
#define ADIS16240_ERROR_ACTIVE (1<<14)
|
|
|
|
#define ADIS16240_MAX_TX 24
|
|
#define ADIS16240_MAX_RX 24
|
|
|
|
/**
|
|
* struct adis16240_state - device instance specific data
|
|
* @us: actual spi_device
|
|
* @work_trigger_to_ring: bh for triggered event handling
|
|
* @inter: used to check if new interrupt has been triggered
|
|
* @last_timestamp: passing timestamp from th to bh of interrupt handler
|
|
* @indio_dev: industrial I/O device structure
|
|
* @trig: data ready trigger registered with iio
|
|
* @tx: transmit buffer
|
|
* @rx: recieve buffer
|
|
* @buf_lock: mutex to protect tx and rx
|
|
**/
|
|
struct adis16240_state {
|
|
struct spi_device *us;
|
|
struct work_struct work_trigger_to_ring;
|
|
s64 last_timestamp;
|
|
struct iio_dev *indio_dev;
|
|
struct iio_trigger *trig;
|
|
u8 *tx;
|
|
u8 *rx;
|
|
struct mutex buf_lock;
|
|
};
|
|
|
|
int adis16240_set_irq(struct device *dev, bool enable);
|
|
|
|
#ifdef CONFIG_IIO_RING_BUFFER
|
|
/* At the moment triggers are only used for ring buffer
|
|
* filling. This may change!
|
|
*/
|
|
|
|
#define ADIS16240_SCAN_SUPPLY 0
|
|
#define ADIS16240_SCAN_ACC_X 1
|
|
#define ADIS16240_SCAN_ACC_Y 2
|
|
#define ADIS16240_SCAN_ACC_Z 3
|
|
#define ADIS16240_SCAN_AUX_ADC 4
|
|
#define ADIS16240_SCAN_TEMP 5
|
|
|
|
void adis16240_remove_trigger(struct iio_dev *indio_dev);
|
|
int adis16240_probe_trigger(struct iio_dev *indio_dev);
|
|
|
|
ssize_t adis16240_read_data_from_ring(struct device *dev,
|
|
struct device_attribute *attr,
|
|
char *buf);
|
|
|
|
|
|
int adis16240_configure_ring(struct iio_dev *indio_dev);
|
|
void adis16240_unconfigure_ring(struct iio_dev *indio_dev);
|
|
|
|
#else /* CONFIG_IIO_RING_BUFFER */
|
|
|
|
static inline void adis16240_remove_trigger(struct iio_dev *indio_dev)
|
|
{
|
|
}
|
|
|
|
static inline int adis16240_probe_trigger(struct iio_dev *indio_dev)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static inline ssize_t
|
|
adis16240_read_data_from_ring(struct device *dev,
|
|
struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static int adis16240_configure_ring(struct iio_dev *indio_dev)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static inline void adis16240_unconfigure_ring(struct iio_dev *indio_dev)
|
|
{
|
|
}
|
|
|
|
#endif /* CONFIG_IIO_RING_BUFFER */
|
|
#endif /* SPI_ADIS16240_H_ */
|