kernel-ark/drivers/firewire/Kconfig
Linus Torvalds c3ca48f062 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: core: ignore link-active bit of new nodes, fix device recognition
  firewire: sbp2: revert obsolete 'fix stall with "Unsolicited response"'
  firewire: core: increase default SPLIT_TIMEOUT value
  firewire: ohci: Misleading kfree in ohci.c::pci_probe/remove
  firewire: ohci: omit IntEvent.busReset check rom AT queueing
  firewire: ohci: prevent starting of iso contexts with empty queue
  firewire: ohci: prevent iso completion callbacks after context stop
  firewire: core: rename some variables
  firewire: nosy: should work on Power Mac G4 PCI too
  firewire: core: fix card->reset_jiffies overflow
  firewire: cdev: remove unneeded reference
  firewire: cdev: always wait for outbound transactions to complete
  firewire: cdev: remove unneeded idr_find() from complete_transaction()
  firewire: ohci: log dead DMA contexts
2011-03-21 10:05:22 -07:00

88 lines
2.9 KiB
Plaintext

menu "IEEE 1394 (FireWire) support"
depends on PCI || BROKEN
# firewire-core does not depend on PCI but is
# not useful without PCI controller driver
config FIREWIRE
tristate "FireWire driver stack"
select CRC_ITU_T
help
This is the new-generation IEEE 1394 (FireWire) driver stack
a.k.a. Juju, a new implementation designed for robustness and
simplicity.
See http://ieee1394.wiki.kernel.org/index.php/Juju_Migration
for information about migration from the older Linux 1394 stack
to the new driver stack.
To compile this driver as a module, say M here: the module will be
called firewire-core.
config FIREWIRE_OHCI
tristate "OHCI-1394 controllers"
depends on PCI && FIREWIRE && MMU
help
Enable this driver if you have a FireWire controller based
on the OHCI specification. For all practical purposes, this
is the only chipset in use, so say Y here.
To compile this driver as a module, say M here: The module will be
called firewire-ohci.
config FIREWIRE_OHCI_DEBUG
bool
depends on FIREWIRE_OHCI
default y
config FIREWIRE_SBP2
tristate "Storage devices (SBP-2 protocol)"
depends on FIREWIRE && SCSI
help
This option enables you to use SBP-2 devices connected to a
FireWire bus. SBP-2 devices include storage devices like
harddisks and DVD drives, also some other FireWire devices
like scanners.
To compile this driver as a module, say M here: The module will be
called firewire-sbp2.
You should also enable support for disks, CD-ROMs, etc. in the SCSI
configuration section.
config FIREWIRE_NET
tristate "IP networking over 1394"
depends on FIREWIRE && INET
help
This enables IPv4 over IEEE 1394, providing IP connectivity with
other implementations of RFC 2734 as found on several operating
systems. Multicast support is currently limited.
To compile this driver as a module, say M here: The module will be
called firewire-net.
config FIREWIRE_NOSY
tristate "Nosy - a FireWire traffic sniffer for PCILynx cards"
depends on PCI
help
Nosy is an IEEE 1394 packet sniffer that is used for protocol
analysis and in development of IEEE 1394 drivers, applications,
or firmwares.
This driver lets you use a Texas Instruments PCILynx 1394 to PCI
link layer controller TSB12LV21/A/B as a low-budget bus analyzer.
PCILynx is a nowadays very rare IEEE 1394 controller which is
not OHCI 1394 compliant.
The following cards are known to be based on PCILynx or PCILynx-2:
IOI IOI-1394TT (PCI card), Unibrain Fireboard 400 PCI Lynx-2
(PCI card), Newer Technology FireWire 2 Go (CardBus card),
Apple Power Mac G3 blue & white and G4 with PCI graphics
(onboard controller).
To compile this driver as a module, say M here: The module will be
called nosy. Source code of a userspace interface to nosy, called
nosy-dump, can be found in tools/firewire/ of the kernel sources.
If unsure, say N.
endmenu