a3c98b8b2e
With OPPs, a device may have multiple operable frequency and voltage sets. However, there can be multiple possible operable sets and a system will need to choose one from them. In order to reduce the power consumption (by reducing frequency and voltage) without affecting the performance too much, a Dynamic Voltage and Frequency Scaling (DVFS) scheme may be used. This patch introduces the DVFS capability to non-CPU devices with OPPs. DVFS is a techique whereby the frequency and supplied voltage of a device is adjusted on-the-fly. DVFS usually sets the frequency as low as possible with given conditions (such as QoS assurance) and adjusts voltage according to the chosen frequency in order to reduce power consumption and heat dissipation. The generic DVFS for devices, devfreq, may appear quite similar with /drivers/cpufreq. However, cpufreq does not allow to have multiple devices registered and is not suitable to have multiple heterogenous devices with different (but simple) governors. Normally, DVFS mechanism controls frequency based on the demand for the device, and then, chooses voltage based on the chosen frequency. devfreq also controls the frequency based on the governor's frequency recommendation and let OPP pick up the pair of frequency and voltage based on the recommended frequency. Then, the chosen OPP is passed to device driver's "target" callback. When PM QoS is going to be used with the devfreq device, the device driver should enable OPPs that are appropriate with the current PM QoS requests. In order to do so, the device driver may call opp_enable and opp_disable at the notifier callback of PM QoS so that PM QoS's update_target() call enables the appropriate OPPs. Note that at least one of OPPs should be enabled at any time; be careful when there is a transition. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mike Turquette <mturquette@ti.com> Acked-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
132 lines
3.6 KiB
Makefile
132 lines
3.6 KiB
Makefile
#
|
|
# Makefile for the Linux kernel device drivers.
|
|
#
|
|
# 15 Sep 2000, Christoph Hellwig <hch@infradead.org>
|
|
# Rewritten to use lists instead of if-statements.
|
|
#
|
|
|
|
obj-y += gpio/
|
|
obj-$(CONFIG_PCI) += pci/
|
|
obj-$(CONFIG_PARISC) += parisc/
|
|
obj-$(CONFIG_RAPIDIO) += rapidio/
|
|
obj-y += video/
|
|
obj-y += idle/
|
|
obj-$(CONFIG_ACPI) += acpi/
|
|
obj-$(CONFIG_SFI) += sfi/
|
|
# PnP must come after ACPI since it will eventually need to check if acpi
|
|
# was used and do nothing if so
|
|
obj-$(CONFIG_PNP) += pnp/
|
|
obj-$(CONFIG_ARM_AMBA) += amba/
|
|
# Many drivers will want to use DMA so this has to be made available
|
|
# really early.
|
|
obj-$(CONFIG_DMA_ENGINE) += dma/
|
|
|
|
obj-$(CONFIG_VIRTIO) += virtio/
|
|
obj-$(CONFIG_XEN) += xen/
|
|
|
|
# regulators early, since some subsystems rely on them to initialize
|
|
obj-$(CONFIG_REGULATOR) += regulator/
|
|
|
|
# tty/ comes before char/ so that the VT console is the boot-time
|
|
# default.
|
|
obj-y += tty/
|
|
obj-y += char/
|
|
|
|
# gpu/ comes after char for AGP vs DRM startup
|
|
obj-y += gpu/
|
|
|
|
obj-$(CONFIG_CONNECTOR) += connector/
|
|
|
|
# i810fb and intelfb depend on char/agp/
|
|
obj-$(CONFIG_FB_I810) += video/i810/
|
|
obj-$(CONFIG_FB_INTEL) += video/intelfb/
|
|
|
|
obj-$(CONFIG_PARPORT) += parport/
|
|
obj-y += base/ block/ misc/ mfd/ nfc/
|
|
obj-$(CONFIG_NUBUS) += nubus/
|
|
obj-y += macintosh/
|
|
obj-$(CONFIG_IDE) += ide/
|
|
obj-$(CONFIG_SCSI) += scsi/
|
|
obj-$(CONFIG_ATA) += ata/
|
|
obj-$(CONFIG_TARGET_CORE) += target/
|
|
obj-$(CONFIG_MTD) += mtd/
|
|
obj-$(CONFIG_SPI) += spi/
|
|
obj-y += net/
|
|
obj-$(CONFIG_ATM) += atm/
|
|
obj-$(CONFIG_FUSION) += message/
|
|
obj-y += firewire/
|
|
obj-$(CONFIG_UIO) += uio/
|
|
obj-y += cdrom/
|
|
obj-y += auxdisplay/
|
|
obj-$(CONFIG_PCCARD) += pcmcia/
|
|
obj-$(CONFIG_DIO) += dio/
|
|
obj-$(CONFIG_SBUS) += sbus/
|
|
obj-$(CONFIG_ZORRO) += zorro/
|
|
obj-$(CONFIG_MAC) += macintosh/
|
|
obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/
|
|
obj-$(CONFIG_PARIDE) += block/paride/
|
|
obj-$(CONFIG_TC) += tc/
|
|
obj-$(CONFIG_UWB) += uwb/
|
|
obj-$(CONFIG_USB_OTG_UTILS) += usb/
|
|
obj-$(CONFIG_USB) += usb/
|
|
obj-$(CONFIG_PCI) += usb/
|
|
obj-$(CONFIG_USB_GADGET) += usb/
|
|
obj-$(CONFIG_SERIO) += input/serio/
|
|
obj-$(CONFIG_GAMEPORT) += input/gameport/
|
|
obj-$(CONFIG_INPUT) += input/
|
|
obj-$(CONFIG_I2O) += message/
|
|
obj-$(CONFIG_RTC_LIB) += rtc/
|
|
obj-y += i2c/ media/
|
|
obj-$(CONFIG_PPS) += pps/
|
|
obj-$(CONFIG_PTP_1588_CLOCK) += ptp/
|
|
obj-$(CONFIG_W1) += w1/
|
|
obj-$(CONFIG_POWER_SUPPLY) += power/
|
|
obj-$(CONFIG_HWMON) += hwmon/
|
|
obj-$(CONFIG_THERMAL) += thermal/
|
|
obj-$(CONFIG_WATCHDOG) += watchdog/
|
|
obj-$(CONFIG_PHONE) += telephony/
|
|
obj-$(CONFIG_MD) += md/
|
|
obj-$(CONFIG_BT) += bluetooth/
|
|
obj-$(CONFIG_ACCESSIBILITY) += accessibility/
|
|
obj-$(CONFIG_ISDN) += isdn/
|
|
obj-$(CONFIG_EDAC) += edac/
|
|
obj-$(CONFIG_MCA) += mca/
|
|
obj-$(CONFIG_EISA) += eisa/
|
|
obj-y += lguest/
|
|
obj-$(CONFIG_CPU_FREQ) += cpufreq/
|
|
obj-$(CONFIG_CPU_IDLE) += cpuidle/
|
|
obj-$(CONFIG_MMC) += mmc/
|
|
obj-$(CONFIG_MEMSTICK) += memstick/
|
|
obj-y += leds/
|
|
obj-$(CONFIG_INFINIBAND) += infiniband/
|
|
obj-$(CONFIG_SGI_SN) += sn/
|
|
obj-y += firmware/
|
|
obj-$(CONFIG_CRYPTO) += crypto/
|
|
obj-$(CONFIG_SUPERH) += sh/
|
|
obj-$(CONFIG_ARCH_SHMOBILE) += sh/
|
|
ifndef CONFIG_ARCH_USES_GETTIMEOFFSET
|
|
obj-y += clocksource/
|
|
endif
|
|
obj-$(CONFIG_DCA) += dca/
|
|
obj-$(CONFIG_HID) += hid/
|
|
obj-$(CONFIG_PPC_PS3) += ps3/
|
|
obj-$(CONFIG_OF) += of/
|
|
obj-$(CONFIG_SSB) += ssb/
|
|
obj-$(CONFIG_BCMA) += bcma/
|
|
obj-$(CONFIG_VHOST_NET) += vhost/
|
|
obj-$(CONFIG_VLYNQ) += vlynq/
|
|
obj-$(CONFIG_STAGING) += staging/
|
|
obj-y += platform/
|
|
obj-y += ieee802154/
|
|
#common clk code
|
|
obj-y += clk/
|
|
|
|
obj-$(CONFIG_HWSPINLOCK) += hwspinlock/
|
|
obj-$(CONFIG_NFC) += nfc/
|
|
obj-$(CONFIG_IOMMU_SUPPORT) += iommu/
|
|
|
|
# Virtualization drivers
|
|
obj-$(CONFIG_VIRT_DRIVERS) += virt/
|
|
|
|
obj-$(CONFIG_PM_DEVFREQ) += devfreq/
|