ee0e87b174
The older add_mtd_device()/add_mtd_partitions() and their removal counterparts will soon be gone. Replace uses with mtd_device_register() and mtd_device_unregister(). Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
869 lines
25 KiB
C
869 lines
25 KiB
C
/*
|
|
* PMC551 PCI Mezzanine Ram Device
|
|
*
|
|
* Author:
|
|
* Mark Ferrell <mferrell@mvista.com>
|
|
* Copyright 1999,2000 Nortel Networks
|
|
*
|
|
* License:
|
|
* As part of this driver was derived from the slram.c driver it
|
|
* falls under the same license, which is GNU General Public
|
|
* License v2
|
|
*
|
|
* Description:
|
|
* This driver is intended to support the PMC551 PCI Ram device
|
|
* from Ramix Inc. The PMC551 is a PMC Mezzanine module for
|
|
* cPCI embedded systems. The device contains a single SROM
|
|
* that initially programs the V370PDC chipset onboard the
|
|
* device, and various banks of DRAM/SDRAM onboard. This driver
|
|
* implements this PCI Ram device as an MTD (Memory Technology
|
|
* Device) so that it can be used to hold a file system, or for
|
|
* added swap space in embedded systems. Since the memory on
|
|
* this board isn't as fast as main memory we do not try to hook
|
|
* it into main memory as that would simply reduce performance
|
|
* on the system. Using it as a block device allows us to use
|
|
* it as high speed swap or for a high speed disk device of some
|
|
* sort. Which becomes very useful on diskless systems in the
|
|
* embedded market I might add.
|
|
*
|
|
* Notes:
|
|
* Due to what I assume is more buggy SROM, the 64M PMC551 I
|
|
* have available claims that all 4 of its DRAM banks have 64MiB
|
|
* of ram configured (making a grand total of 256MiB onboard).
|
|
* This is slightly annoying since the BAR0 size reflects the
|
|
* aperture size, not the dram size, and the V370PDC supplies no
|
|
* other method for memory size discovery. This problem is
|
|
* mostly only relevant when compiled as a module, as the
|
|
* unloading of the module with an aperture size smaller than
|
|
* the ram will cause the driver to detect the onboard memory
|
|
* size to be equal to the aperture size when the module is
|
|
* reloaded. Soooo, to help, the module supports an msize
|
|
* option to allow the specification of the onboard memory, and
|
|
* an asize option, to allow the specification of the aperture
|
|
* size. The aperture must be equal to or less then the memory
|
|
* size, the driver will correct this if you screw it up. This
|
|
* problem is not relevant for compiled in drivers as compiled
|
|
* in drivers only init once.
|
|
*
|
|
* Credits:
|
|
* Saeed Karamooz <saeed@ramix.com> of Ramix INC. for the
|
|
* initial example code of how to initialize this device and for
|
|
* help with questions I had concerning operation of the device.
|
|
*
|
|
* Most of the MTD code for this driver was originally written
|
|
* for the slram.o module in the MTD drivers package which
|
|
* allows the mapping of system memory into an MTD device.
|
|
* Since the PMC551 memory module is accessed in the same
|
|
* fashion as system memory, the slram.c code became a very nice
|
|
* fit to the needs of this driver. All we added was PCI
|
|
* detection/initialization to the driver and automatically figure
|
|
* out the size via the PCI detection.o, later changes by Corey
|
|
* Minyard set up the card to utilize a 1M sliding apature.
|
|
*
|
|
* Corey Minyard <minyard@nortelnetworks.com>
|
|
* * Modified driver to utilize a sliding aperture instead of
|
|
* mapping all memory into kernel space which turned out to
|
|
* be very wasteful.
|
|
* * Located a bug in the SROM's initialization sequence that
|
|
* made the memory unusable, added a fix to code to touch up
|
|
* the DRAM some.
|
|
*
|
|
* Bugs/FIXMEs:
|
|
* * MUST fix the init function to not spin on a register
|
|
* waiting for it to set .. this does not safely handle busted
|
|
* devices that never reset the register correctly which will
|
|
* cause the system to hang w/ a reboot being the only chance at
|
|
* recover. [sort of fixed, could be better]
|
|
* * Add I2C handling of the SROM so we can read the SROM's information
|
|
* about the aperture size. This should always accurately reflect the
|
|
* onboard memory size.
|
|
* * Comb the init routine. It's still a bit cludgy on a few things.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <asm/uaccess.h>
|
|
#include <linux/types.h>
|
|
#include <linux/init.h>
|
|
#include <linux/ptrace.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/string.h>
|
|
#include <linux/timer.h>
|
|
#include <linux/major.h>
|
|
#include <linux/fs.h>
|
|
#include <linux/ioctl.h>
|
|
#include <asm/io.h>
|
|
#include <asm/system.h>
|
|
#include <linux/pci.h>
|
|
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/pmc551.h>
|
|
|
|
static struct mtd_info *pmc551list;
|
|
|
|
static int pmc551_erase(struct mtd_info *mtd, struct erase_info *instr)
|
|
{
|
|
struct mypriv *priv = mtd->priv;
|
|
u32 soff_hi, soff_lo; /* start address offset hi/lo */
|
|
u32 eoff_hi, eoff_lo; /* end address offset hi/lo */
|
|
unsigned long end;
|
|
u_char *ptr;
|
|
size_t retlen;
|
|
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_erase(pos:%ld, len:%ld)\n", (long)instr->addr,
|
|
(long)instr->len);
|
|
#endif
|
|
|
|
end = instr->addr + instr->len - 1;
|
|
|
|
/* Is it past the end? */
|
|
if (end > mtd->size) {
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_erase() out of bounds (%ld > %ld)\n",
|
|
(long)end, (long)mtd->size);
|
|
#endif
|
|
return -EINVAL;
|
|
}
|
|
|
|
eoff_hi = end & ~(priv->asize - 1);
|
|
soff_hi = instr->addr & ~(priv->asize - 1);
|
|
eoff_lo = end & (priv->asize - 1);
|
|
soff_lo = instr->addr & (priv->asize - 1);
|
|
|
|
pmc551_point(mtd, instr->addr, instr->len, &retlen,
|
|
(void **)&ptr, NULL);
|
|
|
|
if (soff_hi == eoff_hi || mtd->size == priv->asize) {
|
|
/* The whole thing fits within one access, so just one shot
|
|
will do it. */
|
|
memset(ptr, 0xff, instr->len);
|
|
} else {
|
|
/* We have to do multiple writes to get all the data
|
|
written. */
|
|
while (soff_hi != eoff_hi) {
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_erase() soff_hi: %ld, "
|
|
"eoff_hi: %ld\n", (long)soff_hi, (long)eoff_hi);
|
|
#endif
|
|
memset(ptr, 0xff, priv->asize);
|
|
if (soff_hi + priv->asize >= mtd->size) {
|
|
goto out;
|
|
}
|
|
soff_hi += priv->asize;
|
|
pmc551_point(mtd, (priv->base_map0 | soff_hi),
|
|
priv->asize, &retlen,
|
|
(void **)&ptr, NULL);
|
|
}
|
|
memset(ptr, 0xff, eoff_lo);
|
|
}
|
|
|
|
out:
|
|
instr->state = MTD_ERASE_DONE;
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_erase() done\n");
|
|
#endif
|
|
|
|
mtd_erase_callback(instr);
|
|
return 0;
|
|
}
|
|
|
|
static int pmc551_point(struct mtd_info *mtd, loff_t from, size_t len,
|
|
size_t *retlen, void **virt, resource_size_t *phys)
|
|
{
|
|
struct mypriv *priv = mtd->priv;
|
|
u32 soff_hi;
|
|
u32 soff_lo;
|
|
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_point(%ld, %ld)\n", (long)from, (long)len);
|
|
#endif
|
|
|
|
if (from + len > mtd->size) {
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_point() out of bounds (%ld > %ld)\n",
|
|
(long)from + len, (long)mtd->size);
|
|
#endif
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* can we return a physical address with this driver? */
|
|
if (phys)
|
|
return -EINVAL;
|
|
|
|
soff_hi = from & ~(priv->asize - 1);
|
|
soff_lo = from & (priv->asize - 1);
|
|
|
|
/* Cheap hack optimization */
|
|
if (priv->curr_map0 != from) {
|
|
pci_write_config_dword(priv->dev, PMC551_PCI_MEM_MAP0,
|
|
(priv->base_map0 | soff_hi));
|
|
priv->curr_map0 = soff_hi;
|
|
}
|
|
|
|
*virt = priv->start + soff_lo;
|
|
*retlen = len;
|
|
return 0;
|
|
}
|
|
|
|
static void pmc551_unpoint(struct mtd_info *mtd, loff_t from, size_t len)
|
|
{
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_unpoint()\n");
|
|
#endif
|
|
}
|
|
|
|
static int pmc551_read(struct mtd_info *mtd, loff_t from, size_t len,
|
|
size_t * retlen, u_char * buf)
|
|
{
|
|
struct mypriv *priv = mtd->priv;
|
|
u32 soff_hi, soff_lo; /* start address offset hi/lo */
|
|
u32 eoff_hi, eoff_lo; /* end address offset hi/lo */
|
|
unsigned long end;
|
|
u_char *ptr;
|
|
u_char *copyto = buf;
|
|
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_read(pos:%ld, len:%ld) asize: %ld\n",
|
|
(long)from, (long)len, (long)priv->asize);
|
|
#endif
|
|
|
|
end = from + len - 1;
|
|
|
|
/* Is it past the end? */
|
|
if (end > mtd->size) {
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_read() out of bounds (%ld > %ld)\n",
|
|
(long)end, (long)mtd->size);
|
|
#endif
|
|
return -EINVAL;
|
|
}
|
|
|
|
soff_hi = from & ~(priv->asize - 1);
|
|
eoff_hi = end & ~(priv->asize - 1);
|
|
soff_lo = from & (priv->asize - 1);
|
|
eoff_lo = end & (priv->asize - 1);
|
|
|
|
pmc551_point(mtd, from, len, retlen, (void **)&ptr, NULL);
|
|
|
|
if (soff_hi == eoff_hi) {
|
|
/* The whole thing fits within one access, so just one shot
|
|
will do it. */
|
|
memcpy(copyto, ptr, len);
|
|
copyto += len;
|
|
} else {
|
|
/* We have to do multiple writes to get all the data
|
|
written. */
|
|
while (soff_hi != eoff_hi) {
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_read() soff_hi: %ld, "
|
|
"eoff_hi: %ld\n", (long)soff_hi, (long)eoff_hi);
|
|
#endif
|
|
memcpy(copyto, ptr, priv->asize);
|
|
copyto += priv->asize;
|
|
if (soff_hi + priv->asize >= mtd->size) {
|
|
goto out;
|
|
}
|
|
soff_hi += priv->asize;
|
|
pmc551_point(mtd, soff_hi, priv->asize, retlen,
|
|
(void **)&ptr, NULL);
|
|
}
|
|
memcpy(copyto, ptr, eoff_lo);
|
|
copyto += eoff_lo;
|
|
}
|
|
|
|
out:
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_read() done\n");
|
|
#endif
|
|
*retlen = copyto - buf;
|
|
return 0;
|
|
}
|
|
|
|
static int pmc551_write(struct mtd_info *mtd, loff_t to, size_t len,
|
|
size_t * retlen, const u_char * buf)
|
|
{
|
|
struct mypriv *priv = mtd->priv;
|
|
u32 soff_hi, soff_lo; /* start address offset hi/lo */
|
|
u32 eoff_hi, eoff_lo; /* end address offset hi/lo */
|
|
unsigned long end;
|
|
u_char *ptr;
|
|
const u_char *copyfrom = buf;
|
|
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_write(pos:%ld, len:%ld) asize:%ld\n",
|
|
(long)to, (long)len, (long)priv->asize);
|
|
#endif
|
|
|
|
end = to + len - 1;
|
|
/* Is it past the end? or did the u32 wrap? */
|
|
if (end > mtd->size) {
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_write() out of bounds (end: %ld, "
|
|
"size: %ld, to: %ld)\n", (long)end, (long)mtd->size,
|
|
(long)to);
|
|
#endif
|
|
return -EINVAL;
|
|
}
|
|
|
|
soff_hi = to & ~(priv->asize - 1);
|
|
eoff_hi = end & ~(priv->asize - 1);
|
|
soff_lo = to & (priv->asize - 1);
|
|
eoff_lo = end & (priv->asize - 1);
|
|
|
|
pmc551_point(mtd, to, len, retlen, (void **)&ptr, NULL);
|
|
|
|
if (soff_hi == eoff_hi) {
|
|
/* The whole thing fits within one access, so just one shot
|
|
will do it. */
|
|
memcpy(ptr, copyfrom, len);
|
|
copyfrom += len;
|
|
} else {
|
|
/* We have to do multiple writes to get all the data
|
|
written. */
|
|
while (soff_hi != eoff_hi) {
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_write() soff_hi: %ld, "
|
|
"eoff_hi: %ld\n", (long)soff_hi, (long)eoff_hi);
|
|
#endif
|
|
memcpy(ptr, copyfrom, priv->asize);
|
|
copyfrom += priv->asize;
|
|
if (soff_hi >= mtd->size) {
|
|
goto out;
|
|
}
|
|
soff_hi += priv->asize;
|
|
pmc551_point(mtd, soff_hi, priv->asize, retlen,
|
|
(void **)&ptr, NULL);
|
|
}
|
|
memcpy(ptr, copyfrom, eoff_lo);
|
|
copyfrom += eoff_lo;
|
|
}
|
|
|
|
out:
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551_write() done\n");
|
|
#endif
|
|
*retlen = copyfrom - buf;
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Fixup routines for the V370PDC
|
|
* PCI device ID 0x020011b0
|
|
*
|
|
* This function basically kick starts the DRAM oboard the card and gets it
|
|
* ready to be used. Before this is done the device reads VERY erratic, so
|
|
* much that it can crash the Linux 2.2.x series kernels when a user cat's
|
|
* /proc/pci .. though that is mainly a kernel bug in handling the PCI DEVSEL
|
|
* register. FIXME: stop spinning on registers .. must implement a timeout
|
|
* mechanism
|
|
* returns the size of the memory region found.
|
|
*/
|
|
static u32 fixup_pmc551(struct pci_dev *dev)
|
|
{
|
|
#ifdef CONFIG_MTD_PMC551_BUGFIX
|
|
u32 dram_data;
|
|
#endif
|
|
u32 size, dcmd, cfg, dtmp;
|
|
u16 cmd, tmp, i;
|
|
u8 bcmd, counter;
|
|
|
|
/* Sanity Check */
|
|
if (!dev) {
|
|
return -ENODEV;
|
|
}
|
|
|
|
/*
|
|
* Attempt to reset the card
|
|
* FIXME: Stop Spinning registers
|
|
*/
|
|
counter = 0;
|
|
/* unlock registers */
|
|
pci_write_config_byte(dev, PMC551_SYS_CTRL_REG, 0xA5);
|
|
/* read in old data */
|
|
pci_read_config_byte(dev, PMC551_SYS_CTRL_REG, &bcmd);
|
|
/* bang the reset line up and down for a few */
|
|
for (i = 0; i < 10; i++) {
|
|
counter = 0;
|
|
bcmd &= ~0x80;
|
|
while (counter++ < 100) {
|
|
pci_write_config_byte(dev, PMC551_SYS_CTRL_REG, bcmd);
|
|
}
|
|
counter = 0;
|
|
bcmd |= 0x80;
|
|
while (counter++ < 100) {
|
|
pci_write_config_byte(dev, PMC551_SYS_CTRL_REG, bcmd);
|
|
}
|
|
}
|
|
bcmd |= (0x40 | 0x20);
|
|
pci_write_config_byte(dev, PMC551_SYS_CTRL_REG, bcmd);
|
|
|
|
/*
|
|
* Take care and turn off the memory on the device while we
|
|
* tweak the configurations
|
|
*/
|
|
pci_read_config_word(dev, PCI_COMMAND, &cmd);
|
|
tmp = cmd & ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY);
|
|
pci_write_config_word(dev, PCI_COMMAND, tmp);
|
|
|
|
/*
|
|
* Disable existing aperture before probing memory size
|
|
*/
|
|
pci_read_config_dword(dev, PMC551_PCI_MEM_MAP0, &dcmd);
|
|
dtmp = (dcmd | PMC551_PCI_MEM_MAP_ENABLE | PMC551_PCI_MEM_MAP_REG_EN);
|
|
pci_write_config_dword(dev, PMC551_PCI_MEM_MAP0, dtmp);
|
|
/*
|
|
* Grab old BAR0 config so that we can figure out memory size
|
|
* This is another bit of kludge going on. The reason for the
|
|
* redundancy is I am hoping to retain the original configuration
|
|
* previously assigned to the card by the BIOS or some previous
|
|
* fixup routine in the kernel. So we read the old config into cfg,
|
|
* then write all 1's to the memory space, read back the result into
|
|
* "size", and then write back all the old config.
|
|
*/
|
|
pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &cfg);
|
|
#ifndef CONFIG_MTD_PMC551_BUGFIX
|
|
pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, ~0);
|
|
pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &size);
|
|
size = (size & PCI_BASE_ADDRESS_MEM_MASK);
|
|
size &= ~(size - 1);
|
|
pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, cfg);
|
|
#else
|
|
/*
|
|
* Get the size of the memory by reading all the DRAM size values
|
|
* and adding them up.
|
|
*
|
|
* KLUDGE ALERT: the boards we are using have invalid column and
|
|
* row mux values. We fix them here, but this will break other
|
|
* memory configurations.
|
|
*/
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK0, &dram_data);
|
|
size = PMC551_DRAM_BLK_GET_SIZE(dram_data);
|
|
dram_data = PMC551_DRAM_BLK_SET_COL_MUX(dram_data, 0x5);
|
|
dram_data = PMC551_DRAM_BLK_SET_ROW_MUX(dram_data, 0x9);
|
|
pci_write_config_dword(dev, PMC551_DRAM_BLK0, dram_data);
|
|
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK1, &dram_data);
|
|
size += PMC551_DRAM_BLK_GET_SIZE(dram_data);
|
|
dram_data = PMC551_DRAM_BLK_SET_COL_MUX(dram_data, 0x5);
|
|
dram_data = PMC551_DRAM_BLK_SET_ROW_MUX(dram_data, 0x9);
|
|
pci_write_config_dword(dev, PMC551_DRAM_BLK1, dram_data);
|
|
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK2, &dram_data);
|
|
size += PMC551_DRAM_BLK_GET_SIZE(dram_data);
|
|
dram_data = PMC551_DRAM_BLK_SET_COL_MUX(dram_data, 0x5);
|
|
dram_data = PMC551_DRAM_BLK_SET_ROW_MUX(dram_data, 0x9);
|
|
pci_write_config_dword(dev, PMC551_DRAM_BLK2, dram_data);
|
|
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK3, &dram_data);
|
|
size += PMC551_DRAM_BLK_GET_SIZE(dram_data);
|
|
dram_data = PMC551_DRAM_BLK_SET_COL_MUX(dram_data, 0x5);
|
|
dram_data = PMC551_DRAM_BLK_SET_ROW_MUX(dram_data, 0x9);
|
|
pci_write_config_dword(dev, PMC551_DRAM_BLK3, dram_data);
|
|
|
|
/*
|
|
* Oops .. something went wrong
|
|
*/
|
|
if ((size &= PCI_BASE_ADDRESS_MEM_MASK) == 0) {
|
|
return -ENODEV;
|
|
}
|
|
#endif /* CONFIG_MTD_PMC551_BUGFIX */
|
|
|
|
if ((cfg & PCI_BASE_ADDRESS_SPACE) != PCI_BASE_ADDRESS_SPACE_MEMORY) {
|
|
return -ENODEV;
|
|
}
|
|
|
|
/*
|
|
* Precharge Dram
|
|
*/
|
|
pci_write_config_word(dev, PMC551_SDRAM_MA, 0x0400);
|
|
pci_write_config_word(dev, PMC551_SDRAM_CMD, 0x00bf);
|
|
|
|
/*
|
|
* Wait until command has gone through
|
|
* FIXME: register spinning issue
|
|
*/
|
|
do {
|
|
pci_read_config_word(dev, PMC551_SDRAM_CMD, &cmd);
|
|
if (counter++ > 100)
|
|
break;
|
|
} while ((PCI_COMMAND_IO) & cmd);
|
|
|
|
/*
|
|
* Turn on auto refresh
|
|
* The loop is taken directly from Ramix's example code. I assume that
|
|
* this must be held high for some duration of time, but I can find no
|
|
* documentation refrencing the reasons why.
|
|
*/
|
|
for (i = 1; i <= 8; i++) {
|
|
pci_write_config_word(dev, PMC551_SDRAM_CMD, 0x0df);
|
|
|
|
/*
|
|
* Make certain command has gone through
|
|
* FIXME: register spinning issue
|
|
*/
|
|
counter = 0;
|
|
do {
|
|
pci_read_config_word(dev, PMC551_SDRAM_CMD, &cmd);
|
|
if (counter++ > 100)
|
|
break;
|
|
} while ((PCI_COMMAND_IO) & cmd);
|
|
}
|
|
|
|
pci_write_config_word(dev, PMC551_SDRAM_MA, 0x0020);
|
|
pci_write_config_word(dev, PMC551_SDRAM_CMD, 0x0ff);
|
|
|
|
/*
|
|
* Wait until command completes
|
|
* FIXME: register spinning issue
|
|
*/
|
|
counter = 0;
|
|
do {
|
|
pci_read_config_word(dev, PMC551_SDRAM_CMD, &cmd);
|
|
if (counter++ > 100)
|
|
break;
|
|
} while ((PCI_COMMAND_IO) & cmd);
|
|
|
|
pci_read_config_dword(dev, PMC551_DRAM_CFG, &dcmd);
|
|
dcmd |= 0x02000000;
|
|
pci_write_config_dword(dev, PMC551_DRAM_CFG, dcmd);
|
|
|
|
/*
|
|
* Check to make certain fast back-to-back, if not
|
|
* then set it so
|
|
*/
|
|
pci_read_config_word(dev, PCI_STATUS, &cmd);
|
|
if ((cmd & PCI_COMMAND_FAST_BACK) == 0) {
|
|
cmd |= PCI_COMMAND_FAST_BACK;
|
|
pci_write_config_word(dev, PCI_STATUS, cmd);
|
|
}
|
|
|
|
/*
|
|
* Check to make certain the DEVSEL is set correctly, this device
|
|
* has a tendency to assert DEVSEL and TRDY when a write is performed
|
|
* to the memory when memory is read-only
|
|
*/
|
|
if ((cmd & PCI_STATUS_DEVSEL_MASK) != 0x0) {
|
|
cmd &= ~PCI_STATUS_DEVSEL_MASK;
|
|
pci_write_config_word(dev, PCI_STATUS, cmd);
|
|
}
|
|
/*
|
|
* Set to be prefetchable and put everything back based on old cfg.
|
|
* it's possible that the reset of the V370PDC nuked the original
|
|
* setup
|
|
*/
|
|
/*
|
|
cfg |= PCI_BASE_ADDRESS_MEM_PREFETCH;
|
|
pci_write_config_dword( dev, PCI_BASE_ADDRESS_0, cfg );
|
|
*/
|
|
|
|
/*
|
|
* Turn PCI memory and I/O bus access back on
|
|
*/
|
|
pci_write_config_word(dev, PCI_COMMAND,
|
|
PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
/*
|
|
* Some screen fun
|
|
*/
|
|
printk(KERN_DEBUG "pmc551: %d%sB (0x%x) of %sprefetchable memory at "
|
|
"0x%llx\n", (size < 1024) ? size : (size < 1048576) ?
|
|
size >> 10 : size >> 20,
|
|
(size < 1024) ? "" : (size < 1048576) ? "Ki" : "Mi", size,
|
|
((dcmd & (0x1 << 3)) == 0) ? "non-" : "",
|
|
(unsigned long long)pci_resource_start(dev, 0));
|
|
|
|
/*
|
|
* Check to see the state of the memory
|
|
*/
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK0, &dcmd);
|
|
printk(KERN_DEBUG "pmc551: DRAM_BLK0 Flags: %s,%s\n"
|
|
"pmc551: DRAM_BLK0 Size: %d at %d\n"
|
|
"pmc551: DRAM_BLK0 Row MUX: %d, Col MUX: %d\n",
|
|
(((0x1 << 1) & dcmd) == 0) ? "RW" : "RO",
|
|
(((0x1 << 0) & dcmd) == 0) ? "Off" : "On",
|
|
PMC551_DRAM_BLK_GET_SIZE(dcmd),
|
|
((dcmd >> 20) & 0x7FF), ((dcmd >> 13) & 0x7),
|
|
((dcmd >> 9) & 0xF));
|
|
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK1, &dcmd);
|
|
printk(KERN_DEBUG "pmc551: DRAM_BLK1 Flags: %s,%s\n"
|
|
"pmc551: DRAM_BLK1 Size: %d at %d\n"
|
|
"pmc551: DRAM_BLK1 Row MUX: %d, Col MUX: %d\n",
|
|
(((0x1 << 1) & dcmd) == 0) ? "RW" : "RO",
|
|
(((0x1 << 0) & dcmd) == 0) ? "Off" : "On",
|
|
PMC551_DRAM_BLK_GET_SIZE(dcmd),
|
|
((dcmd >> 20) & 0x7FF), ((dcmd >> 13) & 0x7),
|
|
((dcmd >> 9) & 0xF));
|
|
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK2, &dcmd);
|
|
printk(KERN_DEBUG "pmc551: DRAM_BLK2 Flags: %s,%s\n"
|
|
"pmc551: DRAM_BLK2 Size: %d at %d\n"
|
|
"pmc551: DRAM_BLK2 Row MUX: %d, Col MUX: %d\n",
|
|
(((0x1 << 1) & dcmd) == 0) ? "RW" : "RO",
|
|
(((0x1 << 0) & dcmd) == 0) ? "Off" : "On",
|
|
PMC551_DRAM_BLK_GET_SIZE(dcmd),
|
|
((dcmd >> 20) & 0x7FF), ((dcmd >> 13) & 0x7),
|
|
((dcmd >> 9) & 0xF));
|
|
|
|
pci_read_config_dword(dev, PMC551_DRAM_BLK3, &dcmd);
|
|
printk(KERN_DEBUG "pmc551: DRAM_BLK3 Flags: %s,%s\n"
|
|
"pmc551: DRAM_BLK3 Size: %d at %d\n"
|
|
"pmc551: DRAM_BLK3 Row MUX: %d, Col MUX: %d\n",
|
|
(((0x1 << 1) & dcmd) == 0) ? "RW" : "RO",
|
|
(((0x1 << 0) & dcmd) == 0) ? "Off" : "On",
|
|
PMC551_DRAM_BLK_GET_SIZE(dcmd),
|
|
((dcmd >> 20) & 0x7FF), ((dcmd >> 13) & 0x7),
|
|
((dcmd >> 9) & 0xF));
|
|
|
|
pci_read_config_word(dev, PCI_COMMAND, &cmd);
|
|
printk(KERN_DEBUG "pmc551: Memory Access %s\n",
|
|
(((0x1 << 1) & cmd) == 0) ? "off" : "on");
|
|
printk(KERN_DEBUG "pmc551: I/O Access %s\n",
|
|
(((0x1 << 0) & cmd) == 0) ? "off" : "on");
|
|
|
|
pci_read_config_word(dev, PCI_STATUS, &cmd);
|
|
printk(KERN_DEBUG "pmc551: Devsel %s\n",
|
|
((PCI_STATUS_DEVSEL_MASK & cmd) == 0x000) ? "Fast" :
|
|
((PCI_STATUS_DEVSEL_MASK & cmd) == 0x200) ? "Medium" :
|
|
((PCI_STATUS_DEVSEL_MASK & cmd) == 0x400) ? "Slow" : "Invalid");
|
|
|
|
printk(KERN_DEBUG "pmc551: %sFast Back-to-Back\n",
|
|
((PCI_COMMAND_FAST_BACK & cmd) == 0) ? "Not " : "");
|
|
|
|
pci_read_config_byte(dev, PMC551_SYS_CTRL_REG, &bcmd);
|
|
printk(KERN_DEBUG "pmc551: EEPROM is under %s control\n"
|
|
"pmc551: System Control Register is %slocked to PCI access\n"
|
|
"pmc551: System Control Register is %slocked to EEPROM access\n",
|
|
(bcmd & 0x1) ? "software" : "hardware",
|
|
(bcmd & 0x20) ? "" : "un", (bcmd & 0x40) ? "" : "un");
|
|
#endif
|
|
return size;
|
|
}
|
|
|
|
/*
|
|
* Kernel version specific module stuffages
|
|
*/
|
|
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_AUTHOR("Mark Ferrell <mferrell@mvista.com>");
|
|
MODULE_DESCRIPTION(PMC551_VERSION);
|
|
|
|
/*
|
|
* Stuff these outside the ifdef so as to not bust compiled in driver support
|
|
*/
|
|
static int msize = 0;
|
|
static int asize = 0;
|
|
|
|
module_param(msize, int, 0);
|
|
MODULE_PARM_DESC(msize, "memory size in MiB [1 - 1024]");
|
|
module_param(asize, int, 0);
|
|
MODULE_PARM_DESC(asize, "aperture size, must be <= memsize [1-1024]");
|
|
|
|
/*
|
|
* PMC551 Card Initialization
|
|
*/
|
|
static int __init init_pmc551(void)
|
|
{
|
|
struct pci_dev *PCI_Device = NULL;
|
|
struct mypriv *priv;
|
|
int found = 0;
|
|
struct mtd_info *mtd;
|
|
u32 length = 0;
|
|
|
|
if (msize) {
|
|
msize = (1 << (ffs(msize) - 1)) << 20;
|
|
if (msize > (1 << 30)) {
|
|
printk(KERN_NOTICE "pmc551: Invalid memory size [%d]\n",
|
|
msize);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
if (asize) {
|
|
asize = (1 << (ffs(asize) - 1)) << 20;
|
|
if (asize > (1 << 30)) {
|
|
printk(KERN_NOTICE "pmc551: Invalid aperture size "
|
|
"[%d]\n", asize);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
printk(KERN_INFO PMC551_VERSION);
|
|
|
|
/*
|
|
* PCU-bus chipset probe.
|
|
*/
|
|
for (;;) {
|
|
|
|
if ((PCI_Device = pci_get_device(PCI_VENDOR_ID_V3_SEMI,
|
|
PCI_DEVICE_ID_V3_SEMI_V370PDC,
|
|
PCI_Device)) == NULL) {
|
|
break;
|
|
}
|
|
|
|
printk(KERN_NOTICE "pmc551: Found PCI V370PDC at 0x%llx\n",
|
|
(unsigned long long)pci_resource_start(PCI_Device, 0));
|
|
|
|
/*
|
|
* The PMC551 device acts VERY weird if you don't init it
|
|
* first. i.e. it will not correctly report devsel. If for
|
|
* some reason the sdram is in a wrote-protected state the
|
|
* device will DEVSEL when it is written to causing problems
|
|
* with the oldproc.c driver in
|
|
* some kernels (2.2.*)
|
|
*/
|
|
if ((length = fixup_pmc551(PCI_Device)) <= 0) {
|
|
printk(KERN_NOTICE "pmc551: Cannot init SDRAM\n");
|
|
break;
|
|
}
|
|
|
|
/*
|
|
* This is needed until the driver is capable of reading the
|
|
* onboard I2C SROM to discover the "real" memory size.
|
|
*/
|
|
if (msize) {
|
|
length = msize;
|
|
printk(KERN_NOTICE "pmc551: Using specified memory "
|
|
"size 0x%x\n", length);
|
|
} else {
|
|
msize = length;
|
|
}
|
|
|
|
mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL);
|
|
if (!mtd) {
|
|
printk(KERN_NOTICE "pmc551: Cannot allocate new MTD "
|
|
"device.\n");
|
|
break;
|
|
}
|
|
|
|
priv = kzalloc(sizeof(struct mypriv), GFP_KERNEL);
|
|
if (!priv) {
|
|
printk(KERN_NOTICE "pmc551: Cannot allocate new MTD "
|
|
"device.\n");
|
|
kfree(mtd);
|
|
break;
|
|
}
|
|
mtd->priv = priv;
|
|
priv->dev = PCI_Device;
|
|
|
|
if (asize > length) {
|
|
printk(KERN_NOTICE "pmc551: reducing aperture size to "
|
|
"fit %dM\n", length >> 20);
|
|
priv->asize = asize = length;
|
|
} else if (asize == 0 || asize == length) {
|
|
printk(KERN_NOTICE "pmc551: Using existing aperture "
|
|
"size %dM\n", length >> 20);
|
|
priv->asize = asize = length;
|
|
} else {
|
|
printk(KERN_NOTICE "pmc551: Using specified aperture "
|
|
"size %dM\n", asize >> 20);
|
|
priv->asize = asize;
|
|
}
|
|
priv->start = pci_iomap(PCI_Device, 0, priv->asize);
|
|
|
|
if (!priv->start) {
|
|
printk(KERN_NOTICE "pmc551: Unable to map IO space\n");
|
|
kfree(mtd->priv);
|
|
kfree(mtd);
|
|
break;
|
|
}
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551: setting aperture to %d\n",
|
|
ffs(priv->asize >> 20) - 1);
|
|
#endif
|
|
|
|
priv->base_map0 = (PMC551_PCI_MEM_MAP_REG_EN
|
|
| PMC551_PCI_MEM_MAP_ENABLE
|
|
| (ffs(priv->asize >> 20) - 1) << 4);
|
|
priv->curr_map0 = priv->base_map0;
|
|
pci_write_config_dword(priv->dev, PMC551_PCI_MEM_MAP0,
|
|
priv->curr_map0);
|
|
|
|
#ifdef CONFIG_MTD_PMC551_DEBUG
|
|
printk(KERN_DEBUG "pmc551: aperture set to %d\n",
|
|
(priv->base_map0 & 0xF0) >> 4);
|
|
#endif
|
|
|
|
mtd->size = msize;
|
|
mtd->flags = MTD_CAP_RAM;
|
|
mtd->erase = pmc551_erase;
|
|
mtd->read = pmc551_read;
|
|
mtd->write = pmc551_write;
|
|
mtd->point = pmc551_point;
|
|
mtd->unpoint = pmc551_unpoint;
|
|
mtd->type = MTD_RAM;
|
|
mtd->name = "PMC551 RAM board";
|
|
mtd->erasesize = 0x10000;
|
|
mtd->writesize = 1;
|
|
mtd->owner = THIS_MODULE;
|
|
|
|
if (mtd_device_register(mtd, NULL, 0)) {
|
|
printk(KERN_NOTICE "pmc551: Failed to register new device\n");
|
|
pci_iounmap(PCI_Device, priv->start);
|
|
kfree(mtd->priv);
|
|
kfree(mtd);
|
|
break;
|
|
}
|
|
|
|
/* Keep a reference as the mtd_device_register worked */
|
|
pci_dev_get(PCI_Device);
|
|
|
|
printk(KERN_NOTICE "Registered pmc551 memory device.\n");
|
|
printk(KERN_NOTICE "Mapped %dMiB of memory from 0x%p to 0x%p\n",
|
|
priv->asize >> 20,
|
|
priv->start, priv->start + priv->asize);
|
|
printk(KERN_NOTICE "Total memory is %d%sB\n",
|
|
(length < 1024) ? length :
|
|
(length < 1048576) ? length >> 10 : length >> 20,
|
|
(length < 1024) ? "" : (length < 1048576) ? "Ki" : "Mi");
|
|
priv->nextpmc551 = pmc551list;
|
|
pmc551list = mtd;
|
|
found++;
|
|
}
|
|
|
|
/* Exited early, reference left over */
|
|
if (PCI_Device)
|
|
pci_dev_put(PCI_Device);
|
|
|
|
if (!pmc551list) {
|
|
printk(KERN_NOTICE "pmc551: not detected\n");
|
|
return -ENODEV;
|
|
} else {
|
|
printk(KERN_NOTICE "pmc551: %d pmc551 devices loaded\n", found);
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* PMC551 Card Cleanup
|
|
*/
|
|
static void __exit cleanup_pmc551(void)
|
|
{
|
|
int found = 0;
|
|
struct mtd_info *mtd;
|
|
struct mypriv *priv;
|
|
|
|
while ((mtd = pmc551list)) {
|
|
priv = mtd->priv;
|
|
pmc551list = priv->nextpmc551;
|
|
|
|
if (priv->start) {
|
|
printk(KERN_DEBUG "pmc551: unmapping %dMiB starting at "
|
|
"0x%p\n", priv->asize >> 20, priv->start);
|
|
pci_iounmap(priv->dev, priv->start);
|
|
}
|
|
pci_dev_put(priv->dev);
|
|
|
|
kfree(mtd->priv);
|
|
mtd_device_unregister(mtd);
|
|
kfree(mtd);
|
|
found++;
|
|
}
|
|
|
|
printk(KERN_NOTICE "pmc551: %d pmc551 devices unloaded\n", found);
|
|
}
|
|
|
|
module_init(init_pmc551);
|
|
module_exit(cleanup_pmc551);
|