kernel-ark/arch/sparc64/kernel/dtlb_prot.S
David S. Miller c9c1083074 [SPARC64]: Fix boot failures on SunBlade-150
The sequence to move over to the Linux trap tables from
the firmware ones needs to be more air tight.  It turns
out that to be %100 safe we do need to be able to translate
OBP mappings in our TLB miss handlers early.

In order not to eat up a lot of kernel image memory with
static page tables, just use the translations array in
the OBP TLB miss handlers.  That solves the bulk of the
problem.

Furthermore, to make sure the OBP TLB miss path will work
even before the fixed MMU globals are loaded, explicitly
load %g1 to TLB_SFSR at the beginning of the i-TLB and
d-TLB miss handlers.

To ease the OBP TLB miss walking of the prom_trans[] array,
we sort it then delete all of the non-OBP entries in there
(for example, there are entries for the kernel image itself
which we're not interested in at all).

We also save about 32K of kernel image size with this change.
Not a bad side effect :-)

There are still some reasons why trampoline.S can't use the
setup_trap_table() yet.  The most noteworthy are:

1) OBP boots secondary processors with non-bias'd stack for
   some reason.  This is easily fixed by using a small bootup
   stack in the kernel image explicitly for this purpose.

2) Doing a firmware call via the normal C call prom_set_trap_table()
   goes through the whole OBP enter/exit sequence that saves and
   restores OBP and Linux kernel state in the MMUs.  This path
   unfortunately does a "flush %g6" while loading up the OBP locked
   TLB entries for the firmware call.

   If we setup the %g6 in the trampoline.S code properly, that
   is in the PAGE_OFFSET linear mapping, but we're not on the
   kernel trap table yet so those addresses won't translate properly.

   One idea is to do a by-hand firmware call like we do in the
   early bootup code and elsewhere here in trampoline.S  But this
   fails as well, as aparently the secondary processors are not
   booted with OBP's special locked TLB entries loaded.  These
   are necessary for the firwmare to processes TLB misses correctly
   up until the point where we take over the trap table.

This does need to be resolved at some point.

Signed-off-by: David S. Miller <davem@davemloft.net>
2005-10-12 12:22:46 -07:00

55 lines
1.3 KiB
ArmAsm

/* $Id: dtlb_prot.S,v 1.22 2001/04/11 23:40:32 davem Exp $
* dtlb_prot.S: DTLB protection trap strategy.
* This is included directly into the trap table.
*
* Copyright (C) 1996,1998 David S. Miller (davem@redhat.com)
* Copyright (C) 1997,1998 Jakub Jelinek (jj@ultra.linux.cz)
*/
/* Ways we can get here:
*
* [TL == 0] 1) User stores to readonly pages.
* [TL == 0] 2) Nucleus stores to user readonly pages.
* [TL > 0] 3) Nucleus stores to user readonly stack frame.
*/
/* PROT ** ICACHE line 1: User DTLB protection trap */
mov TLB_SFSR, %g1
stxa %g0, [%g1] ASI_DMMU ! Clear FaultValid bit
membar #Sync ! Synchronize stores
rdpr %pstate, %g5 ! Move into alt-globals
wrpr %g5, PSTATE_AG|PSTATE_MG, %pstate
rdpr %tl, %g1 ! Need a winfixup?
cmp %g1, 1 ! Trap level >1?
mov TLB_TAG_ACCESS, %g4 ! For reload of vaddr
/* PROT ** ICACHE line 2: More real fault processing */
bgu,pn %xcc, winfix_trampoline ! Yes, perform winfixup
ldxa [%g4] ASI_DMMU, %g5 ! Put tagaccess in %g5
ba,pt %xcc, sparc64_realfault_common ! Nope, normal fault
mov FAULT_CODE_DTLB | FAULT_CODE_WRITE, %g4
nop
nop
nop
nop
/* PROT ** ICACHE line 3: Unused... */
nop
nop
nop
nop
nop
nop
nop
nop
/* PROT ** ICACHE line 4: Unused... */
nop
nop
nop
nop
nop
nop
nop
nop