d237bf4926
This patch adds missing initialization sequence, necessary to get the "Macintosh" version of AEC6280 cards to work in Linux. Without this patch, the driver hangs for several minutes trying to initialize the card and the kernel is left in an unstable state. This patch has been tested fine on ppc and i386. Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org> Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
454 lines
12 KiB
C
454 lines
12 KiB
C
/*
|
|
* linux/drivers/ide/pci/aec62xx.c Version 0.11 March 27, 2002
|
|
*
|
|
* Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
|
|
*
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/config.h>
|
|
#include <linux/types.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/hdreg.h>
|
|
#include <linux/ide.h>
|
|
#include <linux/init.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
struct chipset_bus_clock_list_entry {
|
|
u8 xfer_speed;
|
|
u8 chipset_settings;
|
|
u8 ultra_settings;
|
|
};
|
|
|
|
static struct chipset_bus_clock_list_entry aec6xxx_33_base [] = {
|
|
{ XFER_UDMA_6, 0x31, 0x07 },
|
|
{ XFER_UDMA_5, 0x31, 0x06 },
|
|
{ XFER_UDMA_4, 0x31, 0x05 },
|
|
{ XFER_UDMA_3, 0x31, 0x04 },
|
|
{ XFER_UDMA_2, 0x31, 0x03 },
|
|
{ XFER_UDMA_1, 0x31, 0x02 },
|
|
{ XFER_UDMA_0, 0x31, 0x01 },
|
|
|
|
{ XFER_MW_DMA_2, 0x31, 0x00 },
|
|
{ XFER_MW_DMA_1, 0x31, 0x00 },
|
|
{ XFER_MW_DMA_0, 0x0a, 0x00 },
|
|
{ XFER_PIO_4, 0x31, 0x00 },
|
|
{ XFER_PIO_3, 0x33, 0x00 },
|
|
{ XFER_PIO_2, 0x08, 0x00 },
|
|
{ XFER_PIO_1, 0x0a, 0x00 },
|
|
{ XFER_PIO_0, 0x00, 0x00 },
|
|
{ 0, 0x00, 0x00 }
|
|
};
|
|
|
|
static struct chipset_bus_clock_list_entry aec6xxx_34_base [] = {
|
|
{ XFER_UDMA_6, 0x41, 0x06 },
|
|
{ XFER_UDMA_5, 0x41, 0x05 },
|
|
{ XFER_UDMA_4, 0x41, 0x04 },
|
|
{ XFER_UDMA_3, 0x41, 0x03 },
|
|
{ XFER_UDMA_2, 0x41, 0x02 },
|
|
{ XFER_UDMA_1, 0x41, 0x01 },
|
|
{ XFER_UDMA_0, 0x41, 0x01 },
|
|
|
|
{ XFER_MW_DMA_2, 0x41, 0x00 },
|
|
{ XFER_MW_DMA_1, 0x42, 0x00 },
|
|
{ XFER_MW_DMA_0, 0x7a, 0x00 },
|
|
{ XFER_PIO_4, 0x41, 0x00 },
|
|
{ XFER_PIO_3, 0x43, 0x00 },
|
|
{ XFER_PIO_2, 0x78, 0x00 },
|
|
{ XFER_PIO_1, 0x7a, 0x00 },
|
|
{ XFER_PIO_0, 0x70, 0x00 },
|
|
{ 0, 0x00, 0x00 }
|
|
};
|
|
|
|
#define BUSCLOCK(D) \
|
|
((struct chipset_bus_clock_list_entry *) pci_get_drvdata((D)))
|
|
|
|
|
|
/*
|
|
* TO DO: active tuning and correction of cards without a bios.
|
|
*/
|
|
static u8 pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table)
|
|
{
|
|
for ( ; chipset_table->xfer_speed ; chipset_table++)
|
|
if (chipset_table->xfer_speed == speed) {
|
|
return chipset_table->chipset_settings;
|
|
}
|
|
return chipset_table->chipset_settings;
|
|
}
|
|
|
|
static u8 pci_bus_clock_list_ultra (u8 speed, struct chipset_bus_clock_list_entry * chipset_table)
|
|
{
|
|
for ( ; chipset_table->xfer_speed ; chipset_table++)
|
|
if (chipset_table->xfer_speed == speed) {
|
|
return chipset_table->ultra_settings;
|
|
}
|
|
return chipset_table->ultra_settings;
|
|
}
|
|
|
|
static u8 aec62xx_ratemask (ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
u8 mode;
|
|
|
|
switch(hwif->pci_dev->device) {
|
|
case PCI_DEVICE_ID_ARTOP_ATP865:
|
|
case PCI_DEVICE_ID_ARTOP_ATP865R:
|
|
mode = (hwif->INB(((hwif->channel) ?
|
|
hwif->mate->dma_status :
|
|
hwif->dma_status)) & 0x10) ? 4 : 3;
|
|
break;
|
|
case PCI_DEVICE_ID_ARTOP_ATP860:
|
|
case PCI_DEVICE_ID_ARTOP_ATP860R:
|
|
mode = 2;
|
|
break;
|
|
case PCI_DEVICE_ID_ARTOP_ATP850UF:
|
|
default:
|
|
return 1;
|
|
}
|
|
|
|
if (!eighty_ninty_three(drive))
|
|
mode = min(mode, (u8)1);
|
|
return mode;
|
|
}
|
|
|
|
static int aec6210_tune_chipset (ide_drive_t *drive, u8 xferspeed)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
u16 d_conf = 0;
|
|
u8 speed = ide_rate_filter(aec62xx_ratemask(drive), xferspeed);
|
|
u8 ultra = 0, ultra_conf = 0;
|
|
u8 tmp0 = 0, tmp1 = 0, tmp2 = 0;
|
|
unsigned long flags;
|
|
|
|
local_irq_save(flags);
|
|
/* 0x40|(2*drive->dn): Active, 0x41|(2*drive->dn): Recovery */
|
|
pci_read_config_word(dev, 0x40|(2*drive->dn), &d_conf);
|
|
tmp0 = pci_bus_clock_list(speed, BUSCLOCK(dev));
|
|
d_conf = ((tmp0 & 0xf0) << 4) | (tmp0 & 0xf);
|
|
pci_write_config_word(dev, 0x40|(2*drive->dn), d_conf);
|
|
|
|
tmp1 = 0x00;
|
|
tmp2 = 0x00;
|
|
pci_read_config_byte(dev, 0x54, &ultra);
|
|
tmp1 = ((0x00 << (2*drive->dn)) | (ultra & ~(3 << (2*drive->dn))));
|
|
ultra_conf = pci_bus_clock_list_ultra(speed, BUSCLOCK(dev));
|
|
tmp2 = ((ultra_conf << (2*drive->dn)) | (tmp1 & ~(3 << (2*drive->dn))));
|
|
pci_write_config_byte(dev, 0x54, tmp2);
|
|
local_irq_restore(flags);
|
|
return(ide_config_drive_speed(drive, speed));
|
|
}
|
|
|
|
static int aec6260_tune_chipset (ide_drive_t *drive, u8 xferspeed)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
u8 speed = ide_rate_filter(aec62xx_ratemask(drive), xferspeed);
|
|
u8 unit = (drive->select.b.unit & 0x01);
|
|
u8 tmp1 = 0, tmp2 = 0;
|
|
u8 ultra = 0, drive_conf = 0, ultra_conf = 0;
|
|
unsigned long flags;
|
|
|
|
local_irq_save(flags);
|
|
/* high 4-bits: Active, low 4-bits: Recovery */
|
|
pci_read_config_byte(dev, 0x40|drive->dn, &drive_conf);
|
|
drive_conf = pci_bus_clock_list(speed, BUSCLOCK(dev));
|
|
pci_write_config_byte(dev, 0x40|drive->dn, drive_conf);
|
|
|
|
pci_read_config_byte(dev, (0x44|hwif->channel), &ultra);
|
|
tmp1 = ((0x00 << (4*unit)) | (ultra & ~(7 << (4*unit))));
|
|
ultra_conf = pci_bus_clock_list_ultra(speed, BUSCLOCK(dev));
|
|
tmp2 = ((ultra_conf << (4*unit)) | (tmp1 & ~(7 << (4*unit))));
|
|
pci_write_config_byte(dev, (0x44|hwif->channel), tmp2);
|
|
local_irq_restore(flags);
|
|
return(ide_config_drive_speed(drive, speed));
|
|
}
|
|
|
|
static int aec62xx_tune_chipset (ide_drive_t *drive, u8 speed)
|
|
{
|
|
switch (HWIF(drive)->pci_dev->device) {
|
|
case PCI_DEVICE_ID_ARTOP_ATP865:
|
|
case PCI_DEVICE_ID_ARTOP_ATP865R:
|
|
case PCI_DEVICE_ID_ARTOP_ATP860:
|
|
case PCI_DEVICE_ID_ARTOP_ATP860R:
|
|
return ((int) aec6260_tune_chipset(drive, speed));
|
|
case PCI_DEVICE_ID_ARTOP_ATP850UF:
|
|
return ((int) aec6210_tune_chipset(drive, speed));
|
|
default:
|
|
return -1;
|
|
}
|
|
}
|
|
|
|
static int config_chipset_for_dma (ide_drive_t *drive)
|
|
{
|
|
u8 speed = ide_dma_speed(drive, aec62xx_ratemask(drive));
|
|
|
|
if (!(speed))
|
|
return 0;
|
|
|
|
(void) aec62xx_tune_chipset(drive, speed);
|
|
return ide_dma_enable(drive);
|
|
}
|
|
|
|
static void aec62xx_tune_drive (ide_drive_t *drive, u8 pio)
|
|
{
|
|
u8 speed = 0;
|
|
u8 new_pio = XFER_PIO_0 + ide_get_best_pio_mode(drive, 255, 5, NULL);
|
|
|
|
switch(pio) {
|
|
case 5: speed = new_pio; break;
|
|
case 4: speed = XFER_PIO_4; break;
|
|
case 3: speed = XFER_PIO_3; break;
|
|
case 2: speed = XFER_PIO_2; break;
|
|
case 1: speed = XFER_PIO_1; break;
|
|
default: speed = XFER_PIO_0; break;
|
|
}
|
|
(void) aec62xx_tune_chipset(drive, speed);
|
|
}
|
|
|
|
static int aec62xx_config_drive_xfer_rate (ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct hd_driveid *id = drive->id;
|
|
|
|
if ((id->capability & 1) && drive->autodma) {
|
|
|
|
if (ide_use_dma(drive)) {
|
|
if (config_chipset_for_dma(drive))
|
|
return hwif->ide_dma_on(drive);
|
|
}
|
|
|
|
goto fast_ata_pio;
|
|
|
|
} else if ((id->capability & 8) || (id->field_valid & 2)) {
|
|
fast_ata_pio:
|
|
aec62xx_tune_drive(drive, 5);
|
|
return hwif->ide_dma_off_quietly(drive);
|
|
}
|
|
/* IORDY not supported */
|
|
return 0;
|
|
}
|
|
|
|
static int aec62xx_irq_timeout (ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
|
|
switch(dev->device) {
|
|
case PCI_DEVICE_ID_ARTOP_ATP860:
|
|
case PCI_DEVICE_ID_ARTOP_ATP860R:
|
|
case PCI_DEVICE_ID_ARTOP_ATP865:
|
|
case PCI_DEVICE_ID_ARTOP_ATP865R:
|
|
printk(" AEC62XX time out ");
|
|
default:
|
|
break;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int __devinit init_chipset_aec62xx(struct pci_dev *dev, const char *name)
|
|
{
|
|
int bus_speed = system_bus_clock();
|
|
|
|
if (dev->resource[PCI_ROM_RESOURCE].start) {
|
|
pci_write_config_dword(dev, PCI_ROM_ADDRESS, dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
|
|
printk(KERN_INFO "%s: ROM enabled at 0x%08lx\n", name, dev->resource[PCI_ROM_RESOURCE].start);
|
|
}
|
|
|
|
if (bus_speed <= 33)
|
|
pci_set_drvdata(dev, (void *) aec6xxx_33_base);
|
|
else
|
|
pci_set_drvdata(dev, (void *) aec6xxx_34_base);
|
|
|
|
/* These are necessary to get AEC6280 Macintosh cards to work */
|
|
if ((dev->device == PCI_DEVICE_ID_ARTOP_ATP865) ||
|
|
(dev->device == PCI_DEVICE_ID_ARTOP_ATP865R)) {
|
|
u8 reg49h = 0, reg4ah = 0;
|
|
/* Clear reset and test bits. */
|
|
pci_read_config_byte(dev, 0x49, ®49h);
|
|
pci_write_config_byte(dev, 0x49, reg49h & ~0x30);
|
|
/* Enable chip interrupt output. */
|
|
pci_read_config_byte(dev, 0x4a, ®4ah);
|
|
pci_write_config_byte(dev, 0x4a, reg4ah & ~0x01);
|
|
/* Enable burst mode. */
|
|
pci_read_config_byte(dev, 0x4a, ®4ah);
|
|
pci_write_config_byte(dev, 0x4a, reg4ah | 0x80);
|
|
}
|
|
|
|
return dev->irq;
|
|
}
|
|
|
|
static void __devinit init_hwif_aec62xx(ide_hwif_t *hwif)
|
|
{
|
|
hwif->autodma = 0;
|
|
hwif->tuneproc = &aec62xx_tune_drive;
|
|
hwif->speedproc = &aec62xx_tune_chipset;
|
|
|
|
if (hwif->pci_dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
|
|
hwif->serialized = hwif->channel;
|
|
hwif->no_dsc = 1;
|
|
}
|
|
|
|
if (hwif->mate)
|
|
hwif->mate->serialized = hwif->serialized;
|
|
|
|
if (!hwif->dma_base) {
|
|
hwif->drives[0].autotune = 1;
|
|
hwif->drives[1].autotune = 1;
|
|
return;
|
|
}
|
|
|
|
hwif->ultra_mask = 0x7f;
|
|
hwif->mwdma_mask = 0x07;
|
|
hwif->swdma_mask = 0x07;
|
|
|
|
hwif->ide_dma_check = &aec62xx_config_drive_xfer_rate;
|
|
hwif->ide_dma_lostirq = &aec62xx_irq_timeout;
|
|
hwif->ide_dma_timeout = &aec62xx_irq_timeout;
|
|
if (!noautodma)
|
|
hwif->autodma = 1;
|
|
hwif->drives[0].autodma = hwif->autodma;
|
|
hwif->drives[1].autodma = hwif->autodma;
|
|
}
|
|
|
|
static void __devinit init_dma_aec62xx(ide_hwif_t *hwif, unsigned long dmabase)
|
|
{
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
|
|
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
|
|
u8 reg54h = 0;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&ide_lock, flags);
|
|
pci_read_config_byte(dev, 0x54, ®54h);
|
|
pci_write_config_byte(dev, 0x54, reg54h & ~(hwif->channel ? 0xF0 : 0x0F));
|
|
spin_unlock_irqrestore(&ide_lock, flags);
|
|
} else {
|
|
u8 ata66 = 0;
|
|
pci_read_config_byte(hwif->pci_dev, 0x49, &ata66);
|
|
if (!(hwif->udma_four))
|
|
hwif->udma_four = (ata66&(hwif->channel?0x02:0x01))?0:1;
|
|
}
|
|
|
|
ide_setup_dma(hwif, dmabase, 8);
|
|
}
|
|
|
|
static int __devinit init_setup_aec62xx(struct pci_dev *dev, ide_pci_device_t *d)
|
|
{
|
|
return ide_setup_pci_device(dev, d);
|
|
}
|
|
|
|
static int __devinit init_setup_aec6x80(struct pci_dev *dev, ide_pci_device_t *d)
|
|
{
|
|
unsigned long bar4reg = pci_resource_start(dev, 4);
|
|
|
|
if (inb(bar4reg+2) & 0x10) {
|
|
strcpy(d->name, "AEC6880");
|
|
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP865R)
|
|
strcpy(d->name, "AEC6880R");
|
|
} else {
|
|
strcpy(d->name, "AEC6280");
|
|
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP865R)
|
|
strcpy(d->name, "AEC6280R");
|
|
}
|
|
|
|
return ide_setup_pci_device(dev, d);
|
|
}
|
|
|
|
static ide_pci_device_t aec62xx_chipsets[] __devinitdata = {
|
|
{ /* 0 */
|
|
.name = "AEC6210",
|
|
.init_setup = init_setup_aec62xx,
|
|
.init_chipset = init_chipset_aec62xx,
|
|
.init_hwif = init_hwif_aec62xx,
|
|
.init_dma = init_dma_aec62xx,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
|
|
.bootable = OFF_BOARD,
|
|
},{ /* 1 */
|
|
.name = "AEC6260",
|
|
.init_setup = init_setup_aec62xx,
|
|
.init_chipset = init_chipset_aec62xx,
|
|
.init_hwif = init_hwif_aec62xx,
|
|
.init_dma = init_dma_aec62xx,
|
|
.channels = 2,
|
|
.autodma = NOAUTODMA,
|
|
.bootable = OFF_BOARD,
|
|
},{ /* 2 */
|
|
.name = "AEC6260R",
|
|
.init_setup = init_setup_aec62xx,
|
|
.init_chipset = init_chipset_aec62xx,
|
|
.init_hwif = init_hwif_aec62xx,
|
|
.init_dma = init_dma_aec62xx,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
|
|
.bootable = NEVER_BOARD,
|
|
},{ /* 3 */
|
|
.name = "AEC6X80",
|
|
.init_setup = init_setup_aec6x80,
|
|
.init_chipset = init_chipset_aec62xx,
|
|
.init_hwif = init_hwif_aec62xx,
|
|
.init_dma = init_dma_aec62xx,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.bootable = OFF_BOARD,
|
|
},{ /* 4 */
|
|
.name = "AEC6X80R",
|
|
.init_setup = init_setup_aec6x80,
|
|
.init_chipset = init_chipset_aec62xx,
|
|
.init_hwif = init_hwif_aec62xx,
|
|
.init_dma = init_dma_aec62xx,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.enablebits = {{0x4a,0x02,0x02}, {0x4a,0x04,0x04}},
|
|
.bootable = OFF_BOARD,
|
|
}
|
|
};
|
|
|
|
/**
|
|
* aec62xx_init_one - called when a AEC is found
|
|
* @dev: the aec62xx device
|
|
* @id: the matching pci id
|
|
*
|
|
* Called when the PCI registration layer (or the IDE initialization)
|
|
* finds a device matching our IDE device tables.
|
|
*/
|
|
|
|
static int __devinit aec62xx_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
ide_pci_device_t *d = &aec62xx_chipsets[id->driver_data];
|
|
|
|
return d->init_setup(dev, d);
|
|
}
|
|
|
|
static struct pci_device_id aec62xx_pci_tbl[] = {
|
|
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP850UF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
|
|
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP860, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
|
|
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP860R, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2 },
|
|
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP865, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
|
|
{ PCI_VENDOR_ID_ARTOP, PCI_DEVICE_ID_ARTOP_ATP865R, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, aec62xx_pci_tbl);
|
|
|
|
static struct pci_driver driver = {
|
|
.name = "AEC62xx_IDE",
|
|
.id_table = aec62xx_pci_tbl,
|
|
.probe = aec62xx_init_one,
|
|
};
|
|
|
|
static int aec62xx_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&driver);
|
|
}
|
|
|
|
module_init(aec62xx_ide_init);
|
|
|
|
MODULE_AUTHOR("Andre Hedrick");
|
|
MODULE_DESCRIPTION("PCI driver module for ARTOP AEC62xx IDE");
|
|
MODULE_LICENSE("GPL");
|