kernel-ark/drivers/scsi/psi_roy.h
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

332 lines
16 KiB
C

/****************************************************************************
* Perceptive Solutions, Inc. PCI-2000 device driver for Linux.
*
* psi_roy.h - Linux Host Driver for PCI-2000 IntelliCache SCSI Adapters
*
* Copyright (c) 1997-1999 Perceptive Solutions, Inc.
* All Rights Reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that redistributions of source
* code retain the above copyright notice and this comment without
* modification.
*
* Technical updates and product information at:
* http://www.psidisk.com
*
* Please send questions, comments, bug reports to:
* tech@psidisk.com Technical Support
*
****************************************************************************/
#ifndef ROY_HOST
#define ROY_HOST
/************************************************/
/* PCI setup */
/************************************************/
#define VENDOR_PSI 0x1256
#define DEVICE_ROY_1 0x5201 /* 'R1' */
/************************************************/
/* controller constants */
/************************************************/
#define MAXADAPTER 4 // Increase this and the sizes of the arrays below, if you need more.
#define MAX_BUS 2
#define MAX_UNITS 16
#define TIMEOUT_COMMAND 400 // number of milliSecondos for command busy timeout
/************************************************/
/* I/O address offsets */
/************************************************/
#define RTR_MAILBOX 0x040
#define RTR_LOCAL_DOORBELL 0x060
#define RTR_PCI_DOORBELL 0x064
/************************************************/
/* */
/* Host command codes */
/* */
/************************************************/
#define CMD_READ_CHS 0x01 /* read sectors as specified (CHS mode) */
#define CMD_READ 0x02 /* read sectors as specified (RBA mode) */
#define CMD_READ_SG 0x03 /* read sectors using scatter/gather list */
#define CMD_WRITE_CHS 0x04 /* write sectors as specified (CHS mode) */
#define CMD_WRITE 0x05 /* write sectors as specified (RBA mode) */
#define CMD_WRITE_SG 0x06 /* write sectors using scatter/gather list (LBA mode) */
#define CMD_READ_CHS_SG 0x07 /* read sectors using scatter/gather list (CHS mode) */
#define CMD_WRITE_CHS_SG 0x08 /* write sectors using scatter/gather list (CHS mode) */
#define CMD_VERIFY_CHS 0x09 /* verify data on sectors as specified (CHS mode) */
#define CMD_VERIFY 0x0A /* verify data on sectors as specified (RBA mode) */
#define CMD_DASD_CDB 0x0B /* process CDB for a DASD device */
#define CMD_DASD_CDB_SG 0x0C /* process CDB for a DASD device with scatter/gather */
#define CMD_READ_ABS 0x10 /* read absolute disk */
#define CMD_WRITE_ABS 0x11 /* write absolute disk */
#define CMD_VERIFY_ABS 0x12 /* verify absolute disk */
#define CMD_TEST_READY 0x13 /* test unit ready and return status code */
#define CMD_LOCK_DOOR 0x14 /* lock device door */
#define CMD_UNLOCK_DOOR 0x15 /* unlock device door */
#define CMD_EJECT_MEDIA 0x16 /* eject the media */
#define CMD_UPDATE_CAP 0x17 /* update capacity information */
#define CMD_TEST_PRIV 0x18 /* test and setup private format media */
#define CMD_SCSI_THRU 0x30 /* SCSI pass through CDB */
#define CMD_SCSI_THRU_SG 0x31 /* SCSI pass through CDB with scatter/gather */
#define CMD_SCSI_REQ_SENSE 0x32 /* SCSI pass through request sense after check condition */
#define CMD_DASD_RAID_RQ 0x35 /* request DASD RAID drive data */
#define CMD_DASD_RAID_RQ0 0x31 /* byte 1 subcommand to query for RAID 0 informatation */
#define CMD_DASD_RAID_RQ1 0x32 /* byte 1 subcommand to query for RAID 1 informatation */
#define CMD_DASD_RAID_RQ5 0x33 /* byte 1 subcommand to query for RAID 5 informatation */
#define CMD_DASD_SCSI_INQ 0x36 /* do DASD inquire and return in SCSI format */
#define CMD_DASD_CAP 0x37 /* read DASD capacity */
#define CMD_DASD_INQ 0x38 /* do DASD inquire for type data and return SCSI/EIDE inquiry */
#define CMD_SCSI_INQ 0x39 /* do SCSI inquire */
#define CMD_READ_SETUP 0x3A /* Get setup structures from controller */
#define CMD_WRITE_SETUP 0x3B /* Put setup structures in controller and burn in flash */
#define CMD_READ_CONFIG 0x3C /* Get the entire configuration and setup structures */
#define CMD_WRITE_CONFIG 0x3D /* Put the entire configuration and setup structures in flash */
#define CMD_TEXT_DEVICE 0x3E /* obtain device text */
#define CMD_TEXT_SIGNON 0x3F /* get sign on banner */
#define CMD_QUEUE 0x40 /* any command below this generates a queue tag interrupt to host*/
#define CMD_PREFETCH 0x40 /* prefetch sectors as specified */
#define CMD_TEST_WRITE 0x41 /* Test a device for write protect */
#define CMD_LAST_STATUS 0x42 /* get last command status and error data*/
#define CMD_ABORT 0x43 /* abort command as specified */
#define CMD_ERROR 0x44 /* fetch error code from a tagged op */
#define CMD_DONE 0x45 /* done with operation */
#define CMD_DIAGNOSTICS 0x46 /* execute controller diagnostics and wait for results */
#define CMD_FEATURE_MODE 0x47 /* feature mode control word */
#define CMD_DASD_INQUIRE 0x48 /* inquire as to DASD SCSI device (32 possible) */
#define CMD_FEATURE_QUERY 0x49 /* query the feature control word */
#define CMD_DASD_EJECT 0x4A /* Eject removable media for DASD type */
#define CMD_DASD_LOCK 0x4B /* Lock removable media for DASD type */
#define CMD_DASD_TYPE 0x4C /* obtain DASD device type */
#define CMD_NUM_DEV 0x4D /* obtain the number of devices connected to the controller */
#define CMD_GET_PARMS 0x4E /* obtain device parameters */
#define CMD_SPECIFY 0x4F /* specify operating system for scatter/gather operations */
#define CMD_RAID_GET_DEV 0x50 /* read RAID device geometry */
#define CMD_RAID_READ 0x51 /* read RAID 1 parameter block */
#define CMD_RAID_WRITE 0x52 /* write RAID 1 parameter block */
#define CMD_RAID_LITEUP 0x53 /* Light up the drive light for identification */
#define CMD_RAID_REBUILD 0x54 /* issue a RAID 1 pair rebuild */
#define CMD_RAID_MUTE 0x55 /* mute RAID failure alarm */
#define CMD_RAID_FAIL 0x56 /* induce a RAID failure */
#define CMD_RAID_STATUS 0x57 /* get status of RAID pair */
#define CMD_RAID_STOP 0x58 /* stop any reconstruct in progress */
#define CMD_RAID_START 0x59 /* start reconstruct */
#define CMD_RAID0_READ 0x5A /* read RAID 0 parameter block */
#define CMD_RAID0_WRITE 0x5B /* write RAID 0 parameter block */
#define CMD_RAID5_READ 0x5C /* read RAID 5 parameter block */
#define CMD_RAID5_WRITE 0x5D /* write RAID 5 parameter block */
#define CMD_ERASE_TABLES 0x5F /* erase partition table and RAID signatutures */
#define CMD_SCSI_GET 0x60 /* get SCSI pass through devices */
#define CMD_SCSI_TIMEOUT 0x61 /* set SCSI pass through timeout */
#define CMD_SCSI_ERROR 0x62 /* get SCSI pass through request sense length and residual data count */
#define CMD_GET_SPARMS 0x63 /* get SCSI bus and user parms */
#define CMD_SCSI_ABORT 0x64 /* abort by setting time-out to zero */
#define CMD_CHIRP_CHIRP 0x77 /* make a chirp chirp sound */
#define CMD_GET_LAST_DONE 0x78 /* get tag of last done in progress */
#define CMD_GET_FEATURES 0x79 /* get feature code and ESN */
#define CMD_CLEAR_CACHE 0x7A /* Clear cache on specified device */
#define CMD_BIOS_TEST 0x7B /* Test whether or not to load BIOS */
#define CMD_WAIT_FLUSH 0x7C /* wait for cache flushed and invalidate read cache */
#define CMD_RESET_BUS 0x7D /* reset the SCSI bus */
#define CMD_STARTUP_QRY 0x7E /* startup in progress query */
#define CMD_RESET 0x7F /* reset the controller */
#define CMD_RESTART_RESET 0x80 /* reload and restart the controller at any reset issued */
#define CMD_SOFT_RESET 0x81 /* do a soft reset NOW! */
/************************************************/
/* */
/* Host return errors */
/* */
/************************************************/
#define ERR08_TAGGED 0x80 /* doorbell error ored with tag */
#define ERR16_NONE 0x0000 /* no errors */
#define ERR16_SC_COND_MET 0x0004 /* SCSI status - Condition Met */
#define ERR16_CMD 0x0101 /* command error */
#define ERR16_SC_CHECK_COND 0x0002 /* SCSI status - Check Condition */
#define ERR16_CMD_NOT 0x0201 /* command not supported */
#define ERR16_NO_DEVICE 0x0301 /* invalid device selection */
#define ERR16_SECTOR 0x0202 /* bad sector */
#define ERR16_PROTECT 0x0303 /* write protected */
#define ERR16_NOSECTOR 0x0404 /* sector not found */
#define ERR16_MEDIA 0x0C0C /* invalid media */
#define ERR16_CONTROL 0x2020 /* controller error */
#define ERR16_CONTROL_DMA 0x2120 /* controller DMA engine error */
#define ERR16_NO_ALARM 0x2220 /* alarm is not active */
#define ERR16_OP_BUSY 0x2320 /* operation busy */
#define ERR16_SEEK 0x4040 /* seek failure */
#define ERR16_DEVICE_FAIL 0x4140 /* device has failed */
#define ERR16_TIMEOUT 0x8080 /* timeout error */
#define ERR16_DEV_NOT_READY 0xAAAA /* drive not ready */
#define ERR16_UNDEFINED 0xBBBB /* undefined error */
#define ERR16_WRITE_FAULT 0xCCCC /* write fault */
#define ERR16_INVALID_DEV 0x4001 /* invalid device access */
#define ERR16_DEVICE_BUSY 0x4002 /* device is busy */
#define ERR16_MEMORY 0x4003 /* device pass thru requires too much memory */
#define ERR16_NO_FEATURE 0x40FA /* feature no implemented */
#define ERR16_NOTAG 0x40FD /* no tag space available */
#define ERR16_NOT_READY 0x40FE /* controller not ready error */
#define ERR16_SETUP_FLASH 0x5050 /* error when writing setup to flash memory */
#define ERR16_SETUP_SIZE 0x5051 /* setup block size error */
#define ERR16_SENSE 0xFFFF /* sense opereration failed */
#define ERR16_SC_BUSY 0x0008 /* SCSI status - Busy */
#define ERR16_SC_RES_CONFL 0x0018 /* SCSI status - Reservation Conflict */
#define ERR16_SC_CMD_TERM 0x0022 /* SCSI status - Command Terminated */
#define ERR16_SC_OTHER 0x00FF /* SCSI status - not recognized (any value masked) */
#define ERR16_MEDIA_CHANGED 0x8001 /* devices media has been changed */
#define ERR32_NONE 0x00000000 /* no errors */
#define ERR32_SC_COND_MET 0x00000004 /* SCSI status - Condition Met */
#define ERR32_CMD 0x00010101 /* command error */
#define ERR32_SC_CHECK_COND 0x00020002 /* SCSI status - Check Condition */
#define ERR32_CMD_NOT 0x00030201 /* command not supported */
#define ERR32_NO_DEVICE 0x00040301 /* invalid device selection */
#define ERR32_SECTOR 0x00050202 /* bad sector */
#define ERR32_PROTECT 0x00060303 /* write protected */
#define ERR32_NOSECTOR 0x00070404 /* sector not found */
#define ERR32_MEDIA 0x00080C0C /* invalid media */
#define ERR32_CONTROL 0x00092020 /* controller error */
#define ERR32_CONTROL_DMA 0x000A2120 /* Controller DMA error */
#define ERR32_NO_ALARM 0x000B2220 /* alarm is not active */
#define ERR32_OP_BUSY 0x000C2320 /* operation busy */
#define ERR32_SEEK 0x000D4040 /* seek failure */
#define ERR32_DEVICE_FAIL 0x000E4140 /* device has failed */
#define ERR32_TIMEOUT 0x000F8080 /* timeout error */
#define ERR32_DEV_NOT_READY 0x0010AAAA /* drive not ready */
#define ERR32_UNDEFINED 0x0011BBBB /* undefined error */
#define ERR32_WRITE_FAULT 0x0012CCCC /* write fault */
#define ERR32_INVALID_DEV 0x00134001 /* invalid device access */
#define ERR32_DEVICE_BUSY 0x00144002 /* device is busy */
#define ERR32_MEMORY 0x00154003 /* device pass thru requires too much memory */
#define ERR32_NO_FEATURE 0x001640FA /* feature no implemented */
#define ERR32_NOTAG 0x001740FD /* no tag space available */
#define ERR32_NOT_READY 0x001840FE /* controller not ready error */
#define ERR32_SETUP_FLASH 0x00195050 /* error when writing setup to flash memory */
#define ERR32_SETUP_SIZE 0x001A5051 /* setup block size error */
#define ERR32_SENSE 0x001BFFFF /* sense opereration failed */
#define ERR32_SC_BUSY 0x001C0008 /* SCSI status - Busy */
#define ERR32_SC_RES_CONFL 0x001D0018 /* SCSI status - Reservation Conflict */
#define ERR32_SC_CMD_TERM 0x001E0022 /* SCSI status - Command Terminated */
#define ERR32_SC_OTHER 0x001F00FF /* SCSI status - not recognized (any value masked) */
#define ERR32_MEDIA_CHANGED 0x00208001 /* devices media has been changed */
/************************************************/
/* */
/* Host Operating System specification codes */
/* */
/************************************************/
#define SPEC_INTERRUPT 0x80 /* specification requires host interrupt */
#define SPEC_BACKWARD_SG 0x40 /* specification requires scatter/gather items reversed */
#define SPEC_DOS_BLOCK 0x01 /* DOS DASD blocking on pass through */
#define SPEC_OS2_V3 0x02 /* OS/2 Warp */
#define SPCE_SCO_3242 0x04 /* SCO 3.4.2.2 */
#define SPEC_QNX_4X 0x05 /* QNX 4.XX */
#define SPEC_NOVELL_NWPA 0x08 /* Novell NWPA scatter/gather support */
/************************************************/
/* */
/* Inquire structures */
/* */
/************************************************/
typedef struct _CNT_SCSI_INQ
{
UCHAR devt; /* 00: device type */
UCHAR devtm; /* 01: device type modifier */
UCHAR svers; /* 02: SCSI version */
UCHAR rfmt; /* 03: response data format */
UCHAR adlen; /* 04: additional length of data */
UCHAR res1; /* 05: */
UCHAR res2; /* 06: */
UCHAR fncs; /* 07: functional capabilities */
UCHAR vid[8]; /* 08: vendor ID */
UCHAR pid[16]; /* 10: product ID */
UCHAR rev[4]; /* 20: product revision */
} CNT_SCSI_INQ;
typedef struct _CNT_IDE_INQ
{
USHORT GeneralConfiguration; /* 00 */
USHORT NumberOfCylinders; /* 02 */
USHORT Reserved1; /* 04 */
USHORT NumberOfHeads; /* 06 */
USHORT UnformattedBytesPerTrack; /* 08 */
USHORT UnformattedBytesPerSector; /* 0A */
USHORT SectorsPerTrack; /* 0C */
USHORT VendorUnique1[3]; /* 0E */
USHORT SerialNumber[10]; /* 14 */
USHORT BufferType; /* 28 */
USHORT BufferSectorSize; /* 2A */
USHORT NumberOfEccBytes; /* 2C */
USHORT FirmwareRevision[4]; /* 2E */
USHORT ModelNumber[20]; /* 36 */
UCHAR MaximumBlockTransfer; /* 5E */
UCHAR VendorUnique2; /* 5F */
USHORT DoubleWordIo; /* 60 */
USHORT Capabilities; /* 62 */
USHORT Reserved2; /* 64 */
UCHAR VendorUnique3; /* 66 */
UCHAR PioCycleTimingMode; /* 67 */
UCHAR VendorUnique4; /* 68 */
UCHAR DmaCycleTimingMode; /* 69 */
USHORT TranslationFieldsValid; /* 6A */
USHORT NumberOfCurrentCylinders; /* 6C */
USHORT NumberOfCurrentHeads; /* 6E */
USHORT CurrentSectorsPerTrack; /* 70 */
ULONG CurrentSectorCapacity; /* 72 */
} CNT_IDE_INQ;
typedef struct _DASD_INQUIRE
{
ULONG type; /* 0 = SCSI, 1 = IDE */
union
{
CNT_SCSI_INQ scsi; /* SCSI inquire data */
CNT_IDE_INQ ide; /* IDE inquire data */
} inq;
} DASD_INQUIRE;
/************************************************/
/* */
/* Device Codes */
/* */
/************************************************/
#define DEVC_DASD 0x00 /* Direct-access Storage Device */
#define DEVC_SEQACESS 0x01 /* Sequential-access device */
#define DEVC_PRINTER 0x02 /* Printer device */
#define DEVC_PROCESSOR 0x03 /* Processor device */
#define DEVC_WRITEONCE 0x04 /* Write-once device */
#define DEVC_CDROM 0x05 /* CD-ROM device */
#define DEVC_SCANNER 0x06 /* Scanner device */
#define DEVC_OPTICAL 0x07 /* Optical memory device */
#define DEVC_MEDCHGR 0x08 /* Medium changer device */
#define DEVC_DASD_REMOVABLE 0x80 /* Direct-access storage device, Removable */
#define DEVC_NONE 0xFF /* no device */
// SCSI controls for RAID
#define SC_MY_RAID 0xBF // our special CDB command byte for Win95... interface
#define MY_SCSI_QUERY0 0x31 // byte 1 subcommand to query driver for RAID 0 informatation
#define MY_SCSI_QUERY1 0x32 // byte 1 subcommand to query driver for RAID 1 informatation
#define MY_SCSI_QUERY5 0x33 // byte 1 subcommand to query driver for RAID 5 informatation
#define MY_SCSI_REBUILD 0x40 // byte 1 subcommand to reconstruct a mirrored pair
#define MY_SCSI_DEMOFAIL 0x54 // byte 1 subcommand for RAID failure demonstration
#define MY_SCSI_ALARMMUTE 0x60 // byte 1 subcommand to mute any alarm currently on
#endif