davidlt/kernel-ark
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
714605e4a0
kernel-ark/drivers/usb/host/ohci-hub.c
Alan Stern 71b7497c07 USB: OHCI: fix endless polling behavior 
This patch (as1149) fixes an obscure problem in OHCI polling.  In the
current code, if the RHSC interrupt status flag turns on at a time
when RHSC interrupts are disabled, it will remain on forever:

	The interrupt handler is the only place where RHSC status
	gets turned back off;

	The interrupt handler won't turn RHSC status off because it
	doesn't turn off status flags if the corresponding interrupt
	isn't enabled;

	RHSC interrupts will never get enabled because
	ohci_root_hub_state_changes() doesn't reenable RHSC if RHSC
	status is on!

As a result we will continue polling indefinitely instead of reverting
to interrupt-driven operation, and the root hub will not autosuspend.
This particular sequence of events is not at all unusual; in fact
plugging a USB device into an OHCI controller will usually cause it to
occur.

Of course, this is a bug.  The proper thing to do is to turn off RHSC
status just before reading the actual port status values.  That way
either a port status change will be detected (if it occurs before the
status read) or it will turn RHSC back on.  Possibly both, but that
won't hurt anything.

We can still check for systems in which RHSC is totally broken, by
re-reading RHSC after clearing it and before reading the port
statuses.  (This re-read has to be done anyway, to post the earlier
write.)  If RHSC is on but no port-change statuses are set, then we
know that RHSC is broken and we can avoid re-enabling it.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:41:04 -07:00

820 lines
21 KiB
C
Raw Blame History

/*
* OHCI HCD (Host Controller Driver) for USB.
*
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
*
* This file is licenced under GPL
*/
/*-------------------------------------------------------------------------*/
/*
* OHCI Root Hub ... the nonsharable stuff
*/
#define dbg_port(hc,label,num,value) \
ohci_dbg (hc, \
"%s roothub.portstatus [%d] " \
"= 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s\n", \
label, num, temp, \
(temp & RH_PS_PRSC) ? " PRSC" : "", \
(temp & RH_PS_OCIC) ? " OCIC" : "", \
(temp & RH_PS_PSSC) ? " PSSC" : "", \
(temp & RH_PS_PESC) ? " PESC" : "", \
(temp & RH_PS_CSC) ? " CSC" : "", \
\
(temp & RH_PS_LSDA) ? " LSDA" : "", \
(temp & RH_PS_PPS) ? " PPS" : "", \
(temp & RH_PS_PRS) ? " PRS" : "", \
(temp & RH_PS_POCI) ? " POCI" : "", \
(temp & RH_PS_PSS) ? " PSS" : "", \
\
(temp & RH_PS_PES) ? " PES" : "", \
(temp & RH_PS_CCS) ? " CCS" : "" \
);
/*-------------------------------------------------------------------------*/
#define OHCI_SCHED_ENABLES \
(OHCI_CTRL_CLE|OHCI_CTRL_BLE|OHCI_CTRL_PLE|OHCI_CTRL_IE)
static void dl_done_list (struct ohci_hcd *);
static void finish_unlinks (struct ohci_hcd *, u16);
#ifdef CONFIG_PM
static int ohci_rh_suspend (struct ohci_hcd *ohci, int autostop)
__releases(ohci->lock)
__acquires(ohci->lock)
{
int status = 0;
ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
switch (ohci->hc_control & OHCI_CTRL_HCFS) {
case OHCI_USB_RESUME:
ohci_dbg (ohci, "resume/suspend?\n");
ohci->hc_control &= ~OHCI_CTRL_HCFS;
ohci->hc_control |= OHCI_USB_RESET;
ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
(void) ohci_readl (ohci, &ohci->regs->control);
/* FALL THROUGH */
case OHCI_USB_RESET:
status = -EBUSY;
ohci_dbg (ohci, "needs reinit!\n");
goto done;
case OHCI_USB_SUSPEND:
if (!ohci->autostop) {
ohci_dbg (ohci, "already suspended\n");
goto done;
}
}
ohci_dbg (ohci, "%s root hub\n",
autostop ? "auto-stop" : "suspend");
/* First stop any processing */
if (!autostop && (ohci->hc_control & OHCI_SCHED_ENABLES)) {
ohci->hc_control &= ~OHCI_SCHED_ENABLES;
ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
ohci_writel (ohci, OHCI_INTR_SF, &ohci->regs->intrstatus);
/* sched disables take effect on the next frame,
* then the last WDH could take 6+ msec
*/
ohci_dbg (ohci, "stopping schedules ...\n");
ohci->autostop = 0;
spin_unlock_irq (&ohci->lock);
msleep (8);
spin_lock_irq (&ohci->lock);
}
dl_done_list (ohci);
finish_unlinks (ohci, ohci_frame_no(ohci));
/* maybe resume can wake root hub */
if (ohci_to_hcd(ohci)->self.root_hub->do_remote_wakeup || autostop) {
ohci->hc_control |= OHCI_CTRL_RWE;
} else {
ohci_writel(ohci, OHCI_INTR_RHSC | OHCI_INTR_RD,
&ohci->regs->intrdisable);
ohci->hc_control &= ~OHCI_CTRL_RWE;
}
/* Suspend hub ... this is the "global (to this bus) suspend" mode,
* which doesn't imply ports will first be individually suspended.
*/
ohci->hc_control &= ~OHCI_CTRL_HCFS;
ohci->hc_control |= OHCI_USB_SUSPEND;
ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
(void) ohci_readl (ohci, &ohci->regs->control);
/* no resumes until devices finish suspending */
if (!autostop) {
ohci->next_statechange = jiffies + msecs_to_jiffies (5);
ohci->autostop = 0;
}
done:
return status;
}
static inline struct ed *find_head (struct ed *ed)
{
/* for bulk and control lists */
while (ed->ed_prev)
ed = ed->ed_prev;
return ed;
}
/* caller has locked the root hub */
static int ohci_rh_resume (struct ohci_hcd *ohci)
__releases(ohci->lock)
__acquires(ohci->lock)
{
struct usb_hcd *hcd = ohci_to_hcd (ohci);
u32 temp, enables;
int status = -EINPROGRESS;
int autostopped = ohci->autostop;
ohci->autostop = 0;
ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) {
/* this can happen after resuming a swsusp snapshot */
if (hcd->state == HC_STATE_RESUMING) {
ohci_dbg (ohci, "BIOS/SMM active, control %03x\n",
ohci->hc_control);
status = -EBUSY;
/* this happens when pmcore resumes HC then root */
} else {
ohci_dbg (ohci, "duplicate resume\n");
status = 0;
}
} else switch (ohci->hc_control & OHCI_CTRL_HCFS) {
case OHCI_USB_SUSPEND:
ohci->hc_control &= ~(OHCI_CTRL_HCFS|OHCI_SCHED_ENABLES);
ohci->hc_control |= OHCI_USB_RESUME;
ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
(void) ohci_readl (ohci, &ohci->regs->control);
ohci_dbg (ohci, "%s root hub\n",
autostopped ? "auto-start" : "resume");
break;
case OHCI_USB_RESUME:
/* HCFS changes sometime after INTR_RD */
ohci_dbg(ohci, "%swakeup root hub\n",
autostopped ? "auto-" : "");
break;
case OHCI_USB_OPER:
/* this can happen after resuming a swsusp snapshot */
ohci_dbg (ohci, "snapshot resume? reinit\n");
status = -EBUSY;
break;
default: /* RESET, we lost power */
ohci_dbg (ohci, "lost power\n");
status = -EBUSY;
}
if (status == -EBUSY) {
if (!autostopped) {
spin_unlock_irq (&ohci->lock);
(void) ohci_init (ohci);
status = ohci_restart (ohci);
usb_root_hub_lost_power(hcd->self.root_hub);
spin_lock_irq (&ohci->lock);
}
return status;
}
if (status != -EINPROGRESS)
return status;
if (autostopped)
goto skip_resume;
spin_unlock_irq (&ohci->lock);
/* Some controllers (lucent erratum) need extra-long delays */
msleep (20 /* usb 11.5.1.10 */ + 12 /* 32 msec counter */ + 1);
temp = ohci_readl (ohci, &ohci->regs->control);
temp &= OHCI_CTRL_HCFS;
if (temp != OHCI_USB_RESUME) {
ohci_err (ohci, "controller won't resume\n");
spin_lock_irq(&ohci->lock);
return -EBUSY;
}
/* disable old schedule state, reinit from scratch */
ohci_writel (ohci, 0, &ohci->regs->ed_controlhead);
ohci_writel (ohci, 0, &ohci->regs->ed_controlcurrent);
ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead);
ohci_writel (ohci, 0, &ohci->regs->ed_bulkcurrent);
ohci_writel (ohci, 0, &ohci->regs->ed_periodcurrent);
ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca);
/* Sometimes PCI D3 suspend trashes frame timings ... */
periodic_reinit (ohci);
/* the following code is executed with ohci->lock held and
* irqs disabled if and only if autostopped is true
*/
skip_resume:
/* interrupts might have been disabled */
ohci_writel (ohci, OHCI_INTR_INIT, &ohci->regs->intrenable);
if (ohci->ed_rm_list)
ohci_writel (ohci, OHCI_INTR_SF, &ohci->regs->intrenable);
/* Then re-enable operations */
ohci_writel (ohci, OHCI_USB_OPER, &ohci->regs->control);
(void) ohci_readl (ohci, &ohci->regs->control);
if (!autostopped)
msleep (3);
temp = ohci->hc_control;
temp &= OHCI_CTRL_RWC;
temp |= OHCI_CONTROL_INIT | OHCI_USB_OPER;
ohci->hc_control = temp;
ohci_writel (ohci, temp, &ohci->regs->control);
(void) ohci_readl (ohci, &ohci->regs->control);
/* TRSMRCY */
if (!autostopped) {
msleep (10);
spin_lock_irq (&ohci->lock);
}
/* now ohci->lock is always held and irqs are always disabled */
/* keep it alive for more than ~5x suspend + resume costs */
ohci->next_statechange = jiffies + STATECHANGE_DELAY;
/* maybe turn schedules back on */
enables = 0;
temp = 0;
if (!ohci->ed_rm_list) {
if (ohci->ed_controltail) {
ohci_writel (ohci,
find_head (ohci->ed_controltail)->dma,
&ohci->regs->ed_controlhead);
enables |= OHCI_CTRL_CLE;
temp |= OHCI_CLF;
}
if (ohci->ed_bulktail) {
ohci_writel (ohci, find_head (ohci->ed_bulktail)->dma,
&ohci->regs->ed_bulkhead);
enables |= OHCI_CTRL_BLE;
temp |= OHCI_BLF;
}
}
if (hcd->self.bandwidth_isoc_reqs || hcd->self.bandwidth_int_reqs)
enables |= OHCI_CTRL_PLE|OHCI_CTRL_IE;
if (enables) {
ohci_dbg (ohci, "restarting schedules ... %08x\n", enables);
ohci->hc_control |= enables;
ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
if (temp)
ohci_writel (ohci, temp, &ohci->regs->cmdstatus);
(void) ohci_readl (ohci, &ohci->regs->control);
}
return 0;
}
static int ohci_bus_suspend (struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
int rc;
spin_lock_irq (&ohci->lock);
if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
rc = -ESHUTDOWN;
else
rc = ohci_rh_suspend (ohci, 0);
spin_unlock_irq (&ohci->lock);
return rc;
}
static int ohci_bus_resume (struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
int rc;
if (time_before (jiffies, ohci->next_statechange))
msleep(5);
spin_lock_irq (&ohci->lock);
if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
rc = -ESHUTDOWN;
else
rc = ohci_rh_resume (ohci);
spin_unlock_irq (&ohci->lock);
/* poll until we know a device is connected or we autostop */
if (rc == 0)
usb_hcd_poll_rh_status(hcd);
return rc;
}
/* Carry out the final steps of resuming the controller device */
static void ohci_finish_controller_resume(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
int port;
bool need_reinit = false;
/* See if the controller is already running or has been reset */
ohci->hc_control = ohci_readl(ohci, &ohci->regs->control);
if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) {
need_reinit = true;
} else {
switch (ohci->hc_control & OHCI_CTRL_HCFS) {
case OHCI_USB_OPER:
case OHCI_USB_RESET:
need_reinit = true;
}
}
/* If needed, reinitialize and suspend the root hub */
if (need_reinit) {
spin_lock_irq(&ohci->lock);
hcd->state = HC_STATE_RESUMING;
ohci_rh_resume(ohci);
hcd->state = HC_STATE_QUIESCING;
ohci_rh_suspend(ohci, 0);
hcd->state = HC_STATE_SUSPENDED;
spin_unlock_irq(&ohci->lock);
}
/* Normally just turn on port power and enable interrupts */
else {
ohci_dbg(ohci, "powerup ports\n");
for (port = 0; port < ohci->num_ports; port++)
ohci_writel(ohci, RH_PS_PPS,
&ohci->regs->roothub.portstatus[port]);
ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrenable);
ohci_readl(ohci, &ohci->regs->intrenable);
msleep(20);
}
}
/* Carry out polling-, autostop-, and autoresume-related state changes */
static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
int any_connected, int rhsc_status)
{
int poll_rh = 1;
int rhsc_enable;
/* Some broken controllers never turn off RHCS in the interrupt
* status register. For their sake we won't re-enable RHSC
* interrupts if the interrupt bit is already active.
*/
rhsc_enable = ohci_readl(ohci, &ohci->regs->intrenable) &
OHCI_INTR_RHSC;
switch (ohci->hc_control & OHCI_CTRL_HCFS) {
case OHCI_USB_OPER:
/* If no status changes are pending, enable RHSC interrupts. */
if (!rhsc_enable && !rhsc_status && !changed) {
rhsc_enable = OHCI_INTR_RHSC;
ohci_writel(ohci, rhsc_enable, &ohci->regs->intrenable);
}
/* Keep on polling until we know a device is connected
* and RHSC is enabled, or until we autostop.
*/
if (!ohci->autostop) {
if (any_connected ||
!device_may_wakeup(&ohci_to_hcd(ohci)
->self.root_hub->dev)) {
if (rhsc_enable)
poll_rh = 0;
} else {
ohci->autostop = 1;
ohci->next_statechange = jiffies + HZ;
}
/* if no devices have been attached for one second, autostop */
} else {
if (changed || any_connected) {
ohci->autostop = 0;
ohci->next_statechange = jiffies +
STATECHANGE_DELAY;
} else if (time_after_eq(jiffies,
ohci->next_statechange)
&& !ohci->ed_rm_list
&& !(ohci->hc_control &
OHCI_SCHED_ENABLES)) {
ohci_rh_suspend(ohci, 1);
if (rhsc_enable)
poll_rh = 0;
}
}
break;
case OHCI_USB_SUSPEND:
case OHCI_USB_RESUME:
/* if there is a port change, autostart or ask to be resumed */
if (changed) {
if (ohci->autostop)
ohci_rh_resume(ohci);
else
usb_hcd_resume_root_hub(ohci_to_hcd(ohci));
/* If remote wakeup is disabled, stop polling */
} else if (!ohci->autostop &&
!ohci_to_hcd(ohci)->self.root_hub->
do_remote_wakeup) {
poll_rh = 0;
} else {
/* If no status changes are pending,
* enable RHSC interrupts
*/
if (!rhsc_enable && !rhsc_status) {
rhsc_enable = OHCI_INTR_RHSC;
ohci_writel(ohci, rhsc_enable,
&ohci->regs->intrenable);
}
/* Keep polling until RHSC is enabled */
if (rhsc_enable)
poll_rh = 0;
}
break;
}
return poll_rh;
}
#else /* CONFIG_PM */
static inline int ohci_rh_resume(struct ohci_hcd *ohci)
{
return 0;
}
/* Carry out polling-related state changes.
* autostop isn't used when CONFIG_PM is turned off.
*/
static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
int any_connected, int rhsc_status)
{
/* If RHSC is enabled, don't poll */
if (ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC)
return 0;
/* If status changes are pending, continue polling.
* Conversely, if no status changes are pending but the RHSC
* status bit was set, then RHSC may be broken so continue polling.
*/
if (changed || rhsc_status)
return 1;
/* It's safe to re-enable RHSC interrupts */
ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable);
return 0;
}
#endif /* CONFIG_PM */
/*-------------------------------------------------------------------------*/
/* build "status change" packet (one or two bytes) from HC registers */
static int
ohci_hub_status_data (struct usb_hcd *hcd, char *buf)
{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
int i, changed = 0, length = 1;
int any_connected = 0;
int rhsc_status;
unsigned long flags;
spin_lock_irqsave (&ohci->lock, flags);
if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))
goto done;
/* undocumented erratum seen on at least rev D */
if ((ohci->flags & OHCI_QUIRK_AMD756)
&& (roothub_a (ohci) & RH_A_NDP) > MAX_ROOT_PORTS) {
ohci_warn (ohci, "bogus NDP, rereads as NDP=%d\n",
ohci_readl (ohci, &ohci->regs->roothub.a) & RH_A_NDP);
/* retry later; "should not happen" */
goto done;
}
/* init status */
if (roothub_status (ohci) & (RH_HS_LPSC | RH_HS_OCIC))
buf [0] = changed = 1;
else
buf [0] = 0;
if (ohci->num_ports > 7) {
buf [1] = 0;
length++;
}
/* Clear the RHSC status flag before reading the port statuses */
ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrstatus);
rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
OHCI_INTR_RHSC;
/* look at each port */
for (i = 0; i < ohci->num_ports; i++) {
u32 status = roothub_portstatus (ohci, i);
/* can't autostop if ports are connected */
any_connected |= (status & RH_PS_CCS);
if (status & (RH_PS_CSC | RH_PS_PESC | RH_PS_PSSC
| RH_PS_OCIC | RH_PS_PRSC)) {
changed = 1;
if (i < 7)
buf [0] |= 1 << (i + 1);
else
buf [1] |= 1 << (i - 7);
}
}
hcd->poll_rh = ohci_root_hub_state_changes(ohci, changed,
any_connected, rhsc_status);
done:
spin_unlock_irqrestore (&ohci->lock, flags);
return changed ? length : 0;
}
/*-------------------------------------------------------------------------*/
static void
ohci_hub_descriptor (
struct ohci_hcd *ohci,
struct usb_hub_descriptor *desc
) {
u32 rh = roothub_a (ohci);
u16 temp;
desc->bDescriptorType = 0x29;
desc->bPwrOn2PwrGood = (rh & RH_A_POTPGT) >> 24;
desc->bHubContrCurrent = 0;
desc->bNbrPorts = ohci->num_ports;
temp = 1 + (ohci->num_ports / 8);
desc->bDescLength = 7 + 2 * temp;
temp = 0;
if (rh & RH_A_NPS) /* no power switching? */
temp |= 0x0002;
if (rh & RH_A_PSM) /* per-port power switching? */
temp |= 0x0001;
if (rh & RH_A_NOCP) /* no overcurrent reporting? */
temp |= 0x0010;
else if (rh & RH_A_OCPM) /* per-port overcurrent reporting? */
temp |= 0x0008;
desc->wHubCharacteristics = (__force __u16)cpu_to_hc16(ohci, temp);
/* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */
rh = roothub_b (ohci);
memset(desc->bitmap, 0xff, sizeof(desc->bitmap));
desc->bitmap [0] = rh & RH_B_DR;
if (ohci->num_ports > 7) {
desc->bitmap [1] = (rh & RH_B_DR) >> 8;
desc->bitmap [2] = 0xff;
} else
desc->bitmap [1] = 0xff;
}
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_USB_OTG
static int ohci_start_port_reset (struct usb_hcd *hcd, unsigned port)
{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
u32 status;
if (!port)
return -EINVAL;
port--;
/* start port reset before HNP protocol times out */
status = ohci_readl(ohci, &ohci->regs->roothub.portstatus [port]);
if (!(status & RH_PS_CCS))
return -ENODEV;
/* khubd will finish the reset later */
ohci_writel(ohci, RH_PS_PRS, &ohci->regs->roothub.portstatus [port]);
return 0;
}
#else
#define ohci_start_port_reset NULL
#endif
/*-------------------------------------------------------------------------*/
/* See usb 7.1.7.5: root hubs must issue at least 50 msec reset signaling,
* not necessarily continuous ... to guard against resume signaling.
* The short timeout is safe for non-root hubs, and is backward-compatible
* with earlier Linux hosts.
*/
#ifdef CONFIG_USB_SUSPEND
#define PORT_RESET_MSEC 50
#else
#define PORT_RESET_MSEC 10
#endif
/* this timer value might be vendor-specific ... */
#define PORT_RESET_HW_MSEC 10
/* wrap-aware logic morphed from <linux/jiffies.h> */
#define tick_before(t1,t2) ((s16)(((s16)(t1))-((s16)(t2))) < 0)
/* called from some task, normally khubd */
static inline int root_port_reset (struct ohci_hcd *ohci, unsigned port)
{
__hc32 __iomem *portstat = &ohci->regs->roothub.portstatus [port];
u32 temp = 0;
u16 now = ohci_readl(ohci, &ohci->regs->fmnumber);
u16 reset_done = now + PORT_RESET_MSEC;
int limit_1 = DIV_ROUND_UP(PORT_RESET_MSEC, PORT_RESET_HW_MSEC);
/* build a "continuous enough" reset signal, with up to
* 3msec gap between pulses. scheduler HZ==100 must work;
* this might need to be deadline-scheduled.
*/
do {
int limit_2;
/* spin until any current reset finishes */
limit_2 = PORT_RESET_HW_MSEC * 2;
while (--limit_2 >= 0) {
temp = ohci_readl (ohci, portstat);
/* handle e.g. CardBus eject */
if (temp == ~(u32)0)
return -ESHUTDOWN;
if (!(temp & RH_PS_PRS))
break;
udelay (500);
}
/* timeout (a hardware error) has been observed when
* EHCI sets CF while this driver is resetting a port;
* presumably other disconnect paths might do it too.
*/
if (limit_2 < 0) {
ohci_dbg(ohci,
"port[%d] reset timeout, stat %08x\n",
port, temp);
break;
}
if (!(temp & RH_PS_CCS))
break;
if (temp & RH_PS_PRSC)
ohci_writel (ohci, RH_PS_PRSC, portstat);
/* start the next reset, sleep till it's probably done */
ohci_writel (ohci, RH_PS_PRS, portstat);
msleep(PORT_RESET_HW_MSEC);
now = ohci_readl(ohci, &ohci->regs->fmnumber);
} while (tick_before(now, reset_done) && --limit_1 >= 0);
/* caller synchronizes using PRSC ... and handles PRS
* still being set when this returns.
*/
return 0;
}
static int ohci_hub_control (
struct usb_hcd *hcd,
u16 typeReq,
u16 wValue,
u16 wIndex,
char *buf,
u16 wLength
) {
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
int ports = hcd_to_bus (hcd)->root_hub->maxchild;
u32 temp;
int retval = 0;
if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
return -ESHUTDOWN;
switch (typeReq) {
case ClearHubFeature:
switch (wValue) {
case C_HUB_OVER_CURRENT:
ohci_writel (ohci, RH_HS_OCIC,
&ohci->regs->roothub.status);
case C_HUB_LOCAL_POWER:
break;
default:
goto error;
}
break;
case ClearPortFeature:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
switch (wValue) {
case USB_PORT_FEAT_ENABLE:
temp = RH_PS_CCS;
break;
case USB_PORT_FEAT_C_ENABLE:
temp = RH_PS_PESC;
break;
case USB_PORT_FEAT_SUSPEND:
temp = RH_PS_POCI;
break;
case USB_PORT_FEAT_C_SUSPEND:
temp = RH_PS_PSSC;
break;
case USB_PORT_FEAT_POWER:
temp = RH_PS_LSDA;
break;
case USB_PORT_FEAT_C_CONNECTION:
temp = RH_PS_CSC;
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
temp = RH_PS_OCIC;
break;
case USB_PORT_FEAT_C_RESET:
temp = RH_PS_PRSC;
break;
default:
goto error;
}
ohci_writel (ohci, temp,
&ohci->regs->roothub.portstatus [wIndex]);
// ohci_readl (ohci, &ohci->regs->roothub.portstatus [wIndex]);
break;
case GetHubDescriptor:
ohci_hub_descriptor (ohci, (struct usb_hub_descriptor *) buf);
break;
case GetHubStatus:
temp = roothub_status (ohci) & ~(RH_HS_CRWE | RH_HS_DRWE);
put_unaligned_le32(temp, buf);
break;
case GetPortStatus:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = roothub_portstatus (ohci, wIndex);
put_unaligned_le32(temp, buf);
#ifndef OHCI_VERBOSE_DEBUG
if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
#endif
dbg_port (ohci, "GetStatus", wIndex, temp);
break;
case SetHubFeature:
switch (wValue) {
case C_HUB_OVER_CURRENT:
// FIXME: this can be cleared, yes?
case C_HUB_LOCAL_POWER:
break;
default:
goto error;
}
break;
case SetPortFeature:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
#ifdef CONFIG_USB_OTG
if (hcd->self.otg_port == (wIndex + 1)
&& hcd->self.b_hnp_enable)
ohci->start_hnp(ohci);
else
#endif
ohci_writel (ohci, RH_PS_PSS,
&ohci->regs->roothub.portstatus [wIndex]);
break;
case USB_PORT_FEAT_POWER:
ohci_writel (ohci, RH_PS_PPS,
&ohci->regs->roothub.portstatus [wIndex]);
break;
case USB_PORT_FEAT_RESET:
retval = root_port_reset (ohci, wIndex);
break;
default:
goto error;
}
break;
default:
error:
/* "protocol stall" on error */
retval = -EPIPE;
}
return retval;
}
Reference in New Issue View Git Blame Copy Permalink