kernel-ark/drivers/pcmcia/sa1100_neponset.c
Tim Schmielau cd354f1ae7 [PATCH] remove many unneeded #includes of sched.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:54 -08:00

143 lines
3.4 KiB
C

/*
* linux/drivers/pcmcia/sa1100_neponset.c
*
* Neponset PCMCIA specific routines
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/neponset.h>
#include <asm/hardware/sa1111.h>
#include "sa1111_generic.h"
/*
* Neponset uses the Maxim MAX1600, with the following connections:
*
* MAX1600 Neponset
*
* A0VCC SA-1111 GPIO A<1>
* A1VCC SA-1111 GPIO A<0>
* A0VPP CPLD NCR A0VPP
* A1VPP CPLD NCR A1VPP
* B0VCC SA-1111 GPIO A<2>
* B1VCC SA-1111 GPIO A<3>
* B0VPP ground (slot B is CF)
* B1VPP ground (slot B is CF)
*
* VX VCC (5V)
* VY VCC3_3 (3.3V)
* 12INA 12V
* 12INB ground (slot B is CF)
*
* The MAX1600 CODE pin is tied to ground, placing the device in
* "Standard Intel code" mode. Refer to the Maxim data sheet for
* the corresponding truth table.
*/
static int
neponset_pcmcia_configure_socket(struct soc_pcmcia_socket *skt, const socket_state_t *state)
{
unsigned int ncr_mask, ncr_set, pa_dwr_mask, pa_dwr_set;
int ret;
switch (skt->nr) {
case 0:
pa_dwr_mask = GPIO_A0 | GPIO_A1;
ncr_mask = NCR_A0VPP | NCR_A1VPP;
if (state->Vpp == 0)
ncr_set = 0;
else if (state->Vpp == 120)
ncr_set = NCR_A1VPP;
else if (state->Vpp == state->Vcc)
ncr_set = NCR_A0VPP;
else {
printk(KERN_ERR "%s(): unrecognized VPP %u\n",
__FUNCTION__, state->Vpp);
return -1;
}
break;
case 1:
pa_dwr_mask = GPIO_A2 | GPIO_A3;
ncr_mask = 0;
ncr_set = 0;
if (state->Vpp != state->Vcc && state->Vpp != 0) {
printk(KERN_ERR "%s(): CF slot cannot support VPP %u\n",
__FUNCTION__, state->Vpp);
return -1;
}
break;
default:
return -1;
}
/*
* pa_dwr_set is the mask for selecting Vcc on both sockets.
* pa_dwr_mask selects which bits (and therefore socket) we change.
*/
switch (state->Vcc) {
default:
case 0: pa_dwr_set = 0; break;
case 33: pa_dwr_set = GPIO_A1|GPIO_A2; break;
case 50: pa_dwr_set = GPIO_A0|GPIO_A3; break;
}
ret = sa1111_pcmcia_configure_socket(skt, state);
if (ret == 0) {
unsigned long flags;
local_irq_save(flags);
NCR_0 = (NCR_0 & ~ncr_mask) | ncr_set;
local_irq_restore(flags);
sa1111_set_io(SA1111_DEV(skt->dev), pa_dwr_mask, pa_dwr_set);
}
return 0;
}
static void neponset_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
{
if (skt->nr == 0)
NCR_0 &= ~(NCR_A0VPP | NCR_A1VPP);
sa1111_pcmcia_socket_init(skt);
}
static struct pcmcia_low_level neponset_pcmcia_ops = {
.owner = THIS_MODULE,
.hw_init = sa1111_pcmcia_hw_init,
.hw_shutdown = sa1111_pcmcia_hw_shutdown,
.socket_state = sa1111_pcmcia_socket_state,
.configure_socket = neponset_pcmcia_configure_socket,
.socket_init = neponset_pcmcia_socket_init,
.socket_suspend = sa1111_pcmcia_socket_suspend,
};
int __init pcmcia_neponset_init(struct sa1111_dev *sadev)
{
int ret = -ENODEV;
if (machine_is_assabet()) {
/*
* Set GPIO_A<3:0> to be outputs for the MAX1600,
* and switch to standby mode.
*/
sa1111_set_io_dir(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0, 0);
sa1111_set_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
sa1111_set_sleep_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
ret = sa11xx_drv_pcmcia_probe(&sadev->dev, &neponset_pcmcia_ops, 0, 2);
}
return ret;
}