kernel-ark/drivers/Makefile
Arjan van de Ven 0c406263f0 ide/net: flip the order of SATA and network init
this patch flips the order in which sata and network drivers are initialized.

SATA probing takes quite a bit of time, and with the asynchronous infrastructure
other drivers that run after it can execute in parallel. Network drivers do tend
to take some real time talking to the hardware, so running these later is
a good thing (the sata probe then runs concurrent)

This saves about 15% of my kernels boot time.

Both Dave and Jeff acked this patch and suggested it should go via the async
tree.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
2009-03-28 13:06:16 -07:00

110 lines
3.1 KiB
Makefile

#
# Makefile for the Linux kernel device drivers.
#
# 15 Sep 2000, Christoph Hellwig <hch@infradead.org>
# Rewritten to use lists instead of if-statements.
#
obj-y += gpio/
obj-$(CONFIG_PCI) += pci/
obj-$(CONFIG_PARISC) += parisc/
obj-$(CONFIG_RAPIDIO) += rapidio/
obj-y += video/
obj-$(CONFIG_ACPI) += acpi/
# PnP must come after ACPI since it will eventually need to check if acpi
# was used and do nothing if so
obj-$(CONFIG_PNP) += pnp/
obj-$(CONFIG_ARM_AMBA) += amba/
obj-$(CONFIG_XEN) += xen/
# regulators early, since some subsystems rely on them to initialize
obj-$(CONFIG_REGULATOR) += regulator/
# char/ comes before serial/ etc so that the VT console is the boot-time
# default.
obj-y += char/
# gpu/ comes after char for AGP vs DRM startup
obj-y += gpu/
obj-$(CONFIG_CONNECTOR) += connector/
# i810fb and intelfb depend on char/agp/
obj-$(CONFIG_FB_I810) += video/i810/
obj-$(CONFIG_FB_INTEL) += video/intelfb/
obj-y += serial/
obj-$(CONFIG_PARPORT) += parport/
obj-y += base/ block/ misc/ mfd/ media/
obj-$(CONFIG_NUBUS) += nubus/
obj-y += macintosh/
obj-$(CONFIG_IDE) += ide/
obj-$(CONFIG_SCSI) += scsi/
obj-$(CONFIG_ATA) += ata/
obj-y += net/
obj-$(CONFIG_ATM) += atm/
obj-$(CONFIG_FUSION) += message/
obj-$(CONFIG_FIREWIRE) += firewire/
obj-y += ieee1394/
obj-$(CONFIG_UIO) += uio/
obj-y += cdrom/
obj-y += auxdisplay/
obj-$(CONFIG_MTD) += mtd/
obj-$(CONFIG_SPI) += spi/
obj-$(CONFIG_PCCARD) += pcmcia/
obj-$(CONFIG_DIO) += dio/
obj-$(CONFIG_SBUS) += sbus/
obj-$(CONFIG_ZORRO) += zorro/
obj-$(CONFIG_MAC) += macintosh/
obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/
obj-$(CONFIG_PARIDE) += block/paride/
obj-$(CONFIG_TC) += tc/
obj-$(CONFIG_UWB) += uwb/
obj-$(CONFIG_USB_OTG_UTILS) += usb/otg/
obj-$(CONFIG_USB) += usb/
obj-$(CONFIG_USB_MUSB_HDRC) += usb/musb/
obj-$(CONFIG_PCI) += usb/
obj-$(CONFIG_USB_GADGET) += usb/gadget/
obj-$(CONFIG_SERIO) += input/serio/
obj-$(CONFIG_GAMEPORT) += input/gameport/
obj-$(CONFIG_INPUT) += input/
obj-$(CONFIG_I2O) += message/
obj-$(CONFIG_RTC_LIB) += rtc/
obj-y += i2c/
obj-$(CONFIG_W1) += w1/
obj-$(CONFIG_POWER_SUPPLY) += power/
obj-$(CONFIG_HWMON) += hwmon/
obj-$(CONFIG_THERMAL) += thermal/
obj-$(CONFIG_WATCHDOG) += watchdog/
obj-$(CONFIG_PHONE) += telephony/
obj-$(CONFIG_MD) += md/
obj-$(CONFIG_BT) += bluetooth/
obj-$(CONFIG_ACCESSIBILITY) += accessibility/
obj-$(CONFIG_ISDN) += isdn/
obj-$(CONFIG_EDAC) += edac/
obj-$(CONFIG_MCA) += mca/
obj-$(CONFIG_EISA) += eisa/
obj-y += lguest/
obj-$(CONFIG_CPU_FREQ) += cpufreq/
obj-$(CONFIG_CPU_IDLE) += cpuidle/
obj-y += idle/
obj-$(CONFIG_MMC) += mmc/
obj-$(CONFIG_MEMSTICK) += memstick/
obj-$(CONFIG_NEW_LEDS) += leds/
obj-$(CONFIG_INFINIBAND) += infiniband/
obj-$(CONFIG_SGI_SN) += sn/
obj-y += firmware/
obj-$(CONFIG_CRYPTO) += crypto/
obj-$(CONFIG_SUPERH) += sh/
obj-$(CONFIG_GENERIC_TIME) += clocksource/
obj-$(CONFIG_DMA_ENGINE) += dma/
obj-$(CONFIG_DCA) += dca/
obj-$(CONFIG_HID) += hid/
obj-$(CONFIG_PPC_PS3) += ps3/
obj-$(CONFIG_OF) += of/
obj-$(CONFIG_SSB) += ssb/
obj-$(CONFIG_VIRTIO) += virtio/
obj-$(CONFIG_STAGING) += staging/
obj-y += platform/