kernel-ark/arch/x86/Kconfig.debug
Linus Torvalds ba33ea811e Merge branch 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm updates from Ingo Molnar:
 "This is another big update. Main changes are:

   - lots of x86 system call (and other traps/exceptions) entry code
     enhancements.  In particular the complex parts of the 64-bit entry
     code have been migrated to C code as well, and a number of dusty
     corners have been refreshed.  (Andy Lutomirski)

   - vDSO special mapping robustification and general cleanups (Andy
     Lutomirski)

   - cpufeature refactoring, cleanups and speedups (Borislav Petkov)

   - lots of other changes ..."

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
  x86/cpufeature: Enable new AVX-512 features
  x86/entry/traps: Show unhandled signal for i386 in do_trap()
  x86/entry: Call enter_from_user_mode() with IRQs off
  x86/entry/32: Change INT80 to be an interrupt gate
  x86/entry: Improve system call entry comments
  x86/entry: Remove TIF_SINGLESTEP entry work
  x86/entry/32: Add and check a stack canary for the SYSENTER stack
  x86/entry/32: Simplify and fix up the SYSENTER stack #DB/NMI fixup
  x86/entry: Only allocate space for tss_struct::SYSENTER_stack if needed
  x86/entry: Vastly simplify SYSENTER TF (single-step) handling
  x86/entry/traps: Clear DR6 early in do_debug() and improve the comment
  x86/entry/traps: Clear TIF_BLOCKSTEP on all debug exceptions
  x86/entry/32: Restore FLAGS on SYSEXIT
  x86/entry/32: Filter NT and speed up AC filtering in SYSENTER
  x86/entry/compat: In SYSENTER, sink AC clearing below the existing FLAGS test
  selftests/x86: In syscall_nt, test NT|TF as well
  x86/asm-offsets: Remove PARAVIRT_enabled
  x86/entry/32: Introduce and use X86_BUG_ESPFIX instead of paravirt_enabled
  uprobes: __create_xol_area() must nullify xol_mapping.fault
  x86/cpufeature: Create a new synthetic cpu capability for machine check recovery
  ...
2016-03-15 09:32:27 -07:00

365 lines
11 KiB
Plaintext

menu "Kernel hacking"
config TRACE_IRQFLAGS_SUPPORT
def_bool y
source "lib/Kconfig.debug"
config X86_VERBOSE_BOOTUP
bool "Enable verbose x86 bootup info messages"
default y
---help---
Enables the informational output from the decompression stage
(e.g. bzImage) of the boot. If you disable this you will still
see errors. Disable this if you want silent bootup.
config EARLY_PRINTK
bool "Early printk" if EXPERT
default y
---help---
Write kernel log output directly into the VGA buffer or to a serial
port.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized. For normal operation
it is not recommended because it looks ugly and doesn't cooperate
with klogd/syslogd or the X server. You should normally N here,
unless you want to debug such a crash.
config EARLY_PRINTK_DBGP
bool "Early printk via EHCI debug port"
depends on EARLY_PRINTK && PCI
---help---
Write kernel log output directly into the EHCI debug port.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized. For normal operation
it is not recommended because it looks ugly and doesn't cooperate
with klogd/syslogd or the X server. You should normally N here,
unless you want to debug such a crash. You need usb debug device.
config EARLY_PRINTK_EFI
bool "Early printk via the EFI framebuffer"
depends on EFI && EARLY_PRINTK
select FONT_SUPPORT
---help---
Write kernel log output directly into the EFI framebuffer.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized.
config X86_PTDUMP_CORE
def_bool n
config X86_PTDUMP
tristate "Export kernel pagetable layout to userspace via debugfs"
depends on DEBUG_KERNEL
select DEBUG_FS
select X86_PTDUMP_CORE
---help---
Say Y here if you want to show the kernel pagetable layout in a
debugfs file. This information is only useful for kernel developers
who are working in architecture specific areas of the kernel.
It is probably not a good idea to enable this feature in a production
kernel.
If in doubt, say "N"
config EFI_PGT_DUMP
bool "Dump the EFI pagetable"
depends on EFI
select X86_PTDUMP_CORE
---help---
Enable this if you want to dump the EFI page table before
enabling virtual mode. This can be used to debug miscellaneous
issues with the mapping of the EFI runtime regions into that
table.
config DEBUG_RODATA_TEST
bool "Testcase for the marking rodata read-only"
default y
---help---
This option enables a testcase for the setting rodata read-only
as well as for the change_page_attr() infrastructure.
If in doubt, say "N"
config DEBUG_WX
bool "Warn on W+X mappings at boot"
select X86_PTDUMP_CORE
---help---
Generate a warning if any W+X mappings are found at boot.
This is useful for discovering cases where the kernel is leaving
W+X mappings after applying NX, as such mappings are a security risk.
Look for a message in dmesg output like this:
x86/mm: Checked W+X mappings: passed, no W+X pages found.
or like this, if the check failed:
x86/mm: Checked W+X mappings: FAILED, <N> W+X pages found.
Note that even if the check fails, your kernel is possibly
still fine, as W+X mappings are not a security hole in
themselves, what they do is that they make the exploitation
of other unfixed kernel bugs easier.
There is no runtime or memory usage effect of this option
once the kernel has booted up - it's a one time check.
If in doubt, say "Y".
config DEBUG_SET_MODULE_RONX
bool "Set loadable kernel module data as NX and text as RO"
depends on MODULES
---help---
This option helps catch unintended modifications to loadable
kernel module's text and read-only data. It also prevents execution
of module data. Such protection may interfere with run-time code
patching and dynamic kernel tracing - and they might also protect
against certain classes of kernel exploits.
If in doubt, say "N".
config DEBUG_NX_TEST
tristate "Testcase for the NX non-executable stack feature"
depends on DEBUG_KERNEL && m
---help---
This option enables a testcase for the CPU NX capability
and the software setup of this feature.
If in doubt, say "N"
config DOUBLEFAULT
default y
bool "Enable doublefault exception handler" if EXPERT
---help---
This option allows trapping of rare doublefault exceptions that
would otherwise cause a system to silently reboot. Disabling this
option saves about 4k and might cause you much additional grey
hair.
config DEBUG_TLBFLUSH
bool "Set upper limit of TLB entries to flush one-by-one"
depends on DEBUG_KERNEL
---help---
X86-only for now.
This option allows the user to tune the amount of TLB entries the
kernel flushes one-by-one instead of doing a full TLB flush. In
certain situations, the former is cheaper. This is controlled by the
tlb_flushall_shift knob under /sys/kernel/debug/x86. If you set it
to -1, the code flushes the whole TLB unconditionally. Otherwise,
for positive values of it, the kernel will use single TLB entry
invalidating instructions according to the following formula:
flush_entries <= active_tlb_entries / 2^tlb_flushall_shift
If in doubt, say "N".
config IOMMU_DEBUG
bool "Enable IOMMU debugging"
depends on GART_IOMMU && DEBUG_KERNEL
depends on X86_64
---help---
Force the IOMMU to on even when you have less than 4GB of
memory and add debugging code. On overflow always panic. And
allow to enable IOMMU leak tracing. Can be disabled at boot
time with iommu=noforce. This will also enable scatter gather
list merging. Currently not recommended for production
code. When you use it make sure you have a big enough
IOMMU/AGP aperture. Most of the options enabled by this can
be set more finegrained using the iommu= command line
options. See Documentation/x86/x86_64/boot-options.txt for more
details.
config IOMMU_STRESS
bool "Enable IOMMU stress-test mode"
---help---
This option disables various optimizations in IOMMU related
code to do real stress testing of the IOMMU code. This option
will cause a performance drop and should only be enabled for
testing.
config IOMMU_LEAK
bool "IOMMU leak tracing"
depends on IOMMU_DEBUG && DMA_API_DEBUG
---help---
Add a simple leak tracer to the IOMMU code. This is useful when you
are debugging a buggy device driver that leaks IOMMU mappings.
config HAVE_MMIOTRACE_SUPPORT
def_bool y
config X86_DECODER_SELFTEST
bool "x86 instruction decoder selftest"
depends on DEBUG_KERNEL && KPROBES
depends on !COMPILE_TEST
---help---
Perform x86 instruction decoder selftests at build time.
This option is useful for checking the sanity of x86 instruction
decoder code.
If unsure, say "N".
#
# IO delay types:
#
config IO_DELAY_TYPE_0X80
int
default "0"
config IO_DELAY_TYPE_0XED
int
default "1"
config IO_DELAY_TYPE_UDELAY
int
default "2"
config IO_DELAY_TYPE_NONE
int
default "3"
choice
prompt "IO delay type"
default IO_DELAY_0X80
config IO_DELAY_0X80
bool "port 0x80 based port-IO delay [recommended]"
---help---
This is the traditional Linux IO delay used for in/out_p.
It is the most tested hence safest selection here.
config IO_DELAY_0XED
bool "port 0xed based port-IO delay"
---help---
Use port 0xed as the IO delay. This frees up port 0x80 which is
often used as a hardware-debug port.
config IO_DELAY_UDELAY
bool "udelay based port-IO delay"
---help---
Use udelay(2) as the IO delay method. This provides the delay
while not having any side-effect on the IO port space.
config IO_DELAY_NONE
bool "no port-IO delay"
---help---
No port-IO delay. Will break on old boxes that require port-IO
delay for certain operations. Should work on most new machines.
endchoice
if IO_DELAY_0X80
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_0X80
endif
if IO_DELAY_0XED
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_0XED
endif
if IO_DELAY_UDELAY
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_UDELAY
endif
if IO_DELAY_NONE
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_NONE
endif
config DEBUG_BOOT_PARAMS
bool "Debug boot parameters"
depends on DEBUG_KERNEL
depends on DEBUG_FS
---help---
This option will cause struct boot_params to be exported via debugfs.
config CPA_DEBUG
bool "CPA self-test code"
depends on DEBUG_KERNEL
---help---
Do change_page_attr() self-tests every 30 seconds.
config OPTIMIZE_INLINING
bool "Allow gcc to uninline functions marked 'inline'"
---help---
This option determines if the kernel forces gcc to inline the functions
developers have marked 'inline'. Doing so takes away freedom from gcc to
do what it thinks is best, which is desirable for the gcc 3.x series of
compilers. The gcc 4.x series have a rewritten inlining algorithm and
enabling this option will generate a smaller kernel there. Hopefully
this algorithm is so good that allowing gcc 4.x and above to make the
decision will become the default in the future. Until then this option
is there to test gcc for this.
If unsure, say N.
config DEBUG_ENTRY
bool "Debug low-level entry code"
depends on DEBUG_KERNEL
---help---
This option enables sanity checks in x86's low-level entry code.
Some of these sanity checks may slow down kernel entries and
exits or otherwise impact performance.
This is currently used to help test NMI code.
If unsure, say N.
config DEBUG_NMI_SELFTEST
bool "NMI Selftest"
depends on DEBUG_KERNEL && X86_LOCAL_APIC
---help---
Enabling this option turns on a quick NMI selftest to verify
that the NMI behaves correctly.
This might help diagnose strange hangs that rely on NMI to
function properly.
If unsure, say N.
config DEBUG_IMR_SELFTEST
bool "Isolated Memory Region self test"
default n
depends on INTEL_IMR
---help---
This option enables automated sanity testing of the IMR code.
Some simple tests are run to verify IMR bounds checking, alignment
and overlapping. This option is really only useful if you are
debugging an IMR memory map or are modifying the IMR code and want to
test your changes.
If unsure say N here.
config X86_DEBUG_FPU
bool "Debug the x86 FPU code"
depends on DEBUG_KERNEL
default y
---help---
If this option is enabled then there will be extra sanity
checks and (boot time) debug printouts added to the kernel.
This debugging adds some small amount of runtime overhead
to the kernel.
If unsure, say N.
config PUNIT_ATOM_DEBUG
tristate "ATOM Punit debug driver"
select DEBUG_FS
select IOSF_MBI
---help---
This is a debug driver, which gets the power states
of all Punit North Complex devices. The power states of
each device is exposed as part of the debugfs interface.
The current power state can be read from
/sys/kernel/debug/punit_atom/dev_power_state
endmenu