138b15ed87
This howto made sense in the 1990s when users had to manually configure ISA cards with jumpers or vendor utilities, but with the implementation of PCI it became increasingly less and less relevant, to the point where it has been well over a decade since I last updated it. And there is no value in anyone else taking over updating it either. However the references to it continue to spread as boiler plate text from one Kconfig file into the next. We are not doing end users any favours by pointing them at this old document, so lets kill it with fire, once and for all, to hopefully stop any further spread. No code is changed in this commit, just Kconfig help text. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
67 lines
1.9 KiB
Plaintext
67 lines
1.9 KiB
Plaintext
#
|
|
# Blackfin device configuration
|
|
#
|
|
|
|
config NET_BFIN
|
|
bool "Blackfin devices"
|
|
depends on BF516 || BF518 || BF526 || BF527 || BF536 || BF537
|
|
---help---
|
|
If you have a network (Ethernet) card belonging to this class, say Y.
|
|
|
|
If unsure, say Y.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the remaining Blackfin card questions. If you say Y, you will be
|
|
asked for your specific card in the following questions.
|
|
|
|
if NET_BFIN
|
|
|
|
config BFIN_MAC
|
|
tristate "Blackfin on-chip MAC support"
|
|
depends on (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
|
|
select CRC32
|
|
select MII
|
|
select PHYLIB
|
|
select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
|
|
---help---
|
|
This is the driver for Blackfin on-chip mac device. Say Y if you want
|
|
it compiled into the kernel. This driver is also available as a
|
|
module ( = code which can be inserted in and removed from the running
|
|
kernel whenever you want). The module will be called bfin_mac.
|
|
|
|
config BFIN_MAC_USE_L1
|
|
bool "Use L1 memory for rx/tx packets"
|
|
depends on BFIN_MAC && (BF527 || BF537)
|
|
default y
|
|
---help---
|
|
To get maximum network performance, you should use L1 memory as rx/tx
|
|
buffers. Say N here if you want to reserve L1 memory for other uses.
|
|
|
|
config BFIN_TX_DESC_NUM
|
|
int "Number of transmit buffer packets"
|
|
depends on BFIN_MAC
|
|
range 6 10 if BFIN_MAC_USE_L1
|
|
range 10 100
|
|
default "10"
|
|
---help---
|
|
Set the number of buffer packets used in driver.
|
|
|
|
config BFIN_RX_DESC_NUM
|
|
int "Number of receive buffer packets"
|
|
depends on BFIN_MAC
|
|
range 20 64
|
|
default "20"
|
|
---help---
|
|
Set the number of buffer packets used in driver.
|
|
|
|
config BFIN_MAC_USE_HWSTAMP
|
|
bool "Use IEEE 1588 hwstamp"
|
|
depends on BFIN_MAC && BF518
|
|
select PTP_1588_CLOCK
|
|
default y
|
|
---help---
|
|
To support the IEEE 1588 Precision Time Protocol (PTP), select y here
|
|
|
|
endif # NET_BFIN
|