davidlt/kernel-ark
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
329f7dba5f
kernel-ark/drivers/usb/input/Kconfig
Stelian Pop f7214ff4e8 [PATCH] USB: add apple usb touchpad driver 
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.

This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
    * appletouch is a full kernel driver, no userspace program is necessary
    * appletouch can be interfaced with the synaptics X11 driver[2], in order
      to have touchpad acceleration, scrolling, two/three finger tap, etc.

This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.

Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-12 12:23:39 -07:00

309 lines
10 KiB
Plaintext
Raw Blame History

#
# USB Input driver configuration
#
comment "USB Input Devices"
depends on USB
config USB_HID
tristate "USB Human Interface Device (full HID) support"
depends on USB
---help---
Say Y here if you want full HID support to connect keyboards,
mice, joysticks, graphic tablets, or any other HID based devices
to your computer via USB. You also need to select HID Input layer
support (below) if you want to use keyboards, mice, joysticks and
the like ... as well as Uninterruptible Power Supply (UPS) and
monitor control devices.
You can't use this driver and the HIDBP (Boot Protocol) keyboard
and mouse drivers at the same time. More information is available:
<file:Documentation/input/input.txt>.
If unsure, say Y.
To compile this driver as a module, choose M here: the
module will be called usbhid.
comment "Input core support is needed for USB HID input layer or HIDBP support"
depends on USB_HID && INPUT=n
config USB_HIDINPUT
bool "HID input layer support"
default y
depends on INPUT && USB_HID
help
Say Y here if you want to use a USB keyboard, mouse or joystick,
or any other HID input device.
If unsure, say Y.
config HID_FF
bool "Force feedback support (EXPERIMENTAL)"
depends on USB_HIDINPUT && EXPERIMENTAL
help
Say Y here is you want force feedback support for a few HID devices.
See below for a list of supported devices.
See <file:Documentation/input/ff.txt> for a description of the force
feedback API.
If unsure, say N.
config HID_PID
bool "PID Devices (Microsoft Sidewinder Force Feedback 2)"
depends on HID_FF
help
Say Y here if you have a PID-compliant joystick and wish to enable force
feedback for it. The Microsoft Sidewinder Force Feedback 2 is one such
device.
config LOGITECH_FF
bool "Logitech WingMan *3D support"
depends on HID_FF
help
Say Y here if you have one of these devices:
- Logitech WingMan Cordless RumblePad
- Logitech WingMan Force 3D
and if you want to enable force feedback for them.
Note: if you say N here, this device will still be supported, but without
force feedback.
config THRUSTMASTER_FF
bool "ThrustMaster FireStorm Dual Power 2 support (EXPERIMENTAL)"
depends on HID_FF && EXPERIMENTAL
help
Say Y here if you have a THRUSTMASTER FireStore Dual Power 2,
and want to enable force feedback support for it.
Note: if you say N here, this device will still be supported, but without
force feedback.
config USB_HIDDEV
bool "/dev/hiddev raw HID device support"
depends on USB_HID
help
Say Y here if you want to support HID devices (from the USB
specification standpoint) that aren't strictly user interface
devices, like monitor controls and Uninterruptable Power Supplies.
This module supports these devices separately using a separate
event interface on /dev/usb/hiddevX (char 180:96 to 180:111).
If unsure, say Y.
menu "USB HID Boot Protocol drivers"
depends on USB!=n && USB_HID!=y
config USB_KBD
tristate "USB HIDBP Keyboard (simple Boot) support"
depends on USB && INPUT
---help---
Say Y here only if you are absolutely sure that you don't want
to use the generic HID driver for your USB keyboard and prefer
to use the keyboard in its limited Boot Protocol mode instead.
This is almost certainly not what you want. This is mostly
useful for embedded applications or simple keyboards.
To compile this driver as a module, choose M here: the
module will be called usbkbd.
If even remotely unsure, say N.
config USB_MOUSE
tristate "USB HIDBP Mouse (simple Boot) support"
depends on USB && INPUT
---help---
Say Y here only if you are absolutely sure that you don't want
to use the generic HID driver for your USB mouse and prefer
to use the mouse in its limited Boot Protocol mode instead.
This is almost certainly not what you want. This is mostly
useful for embedded applications or simple mice.
To compile this driver as a module, choose M here: the
module will be called usbmouse.
If even remotely unsure, say N.
endmenu
config USB_AIPTEK
tristate "Aiptek 6000U/8000U tablet support"
depends on USB && INPUT
help
Say Y here if you want to use the USB version of the Aiptek 6000U
or Aiptek 8000U tablet. Make sure to say Y to "Mouse support"
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
(CONFIG_INPUT_EVDEV) as well.
To compile this driver as a module, choose M here: the
module will be called aiptek.
config USB_WACOM
tristate "Wacom Intuos/Graphire tablet support"
depends on USB && INPUT
help
Say Y here if you want to use the USB version of the Wacom Intuos
or Graphire tablet. Make sure to say Y to "Mouse support"
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
(CONFIG_INPUT_EVDEV) as well.
To compile this driver as a module, choose M here: the
module will be called wacom.
config USB_ACECAD
tristate "Acecad Flair tablet support"
depends on USB && INPUT
help
Say Y here if you want to use the USB version of the Acecad Flair
tablet. Make sure to say Y to "Mouse support"
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
(CONFIG_INPUT_EVDEV) as well.
To compile this driver as a module, choose M here: the
module will be called acecad.
config USB_KBTAB
tristate "KB Gear JamStudio tablet support"
depends on USB && INPUT
help
Say Y here if you want to use the USB version of the KB Gear
JamStudio tablet. Make sure to say Y to "Mouse support"
(CONFIG_INPUT_MOUSEDEV) and/or "Event interface support"
(CONFIG_INPUT_EVDEV) as well.
To compile this driver as a module, choose M here: the
module will be called kbtab.
config USB_POWERMATE
tristate "Griffin PowerMate and Contour Jog support"
depends on USB && INPUT
---help---
Say Y here if you want to use Griffin PowerMate or Contour Jog devices.
These are aluminum dials which can measure clockwise and anticlockwise
rotation. The dial also acts as a pushbutton. The base contains an LED
which can be instructed to pulse or to switch to a particular intensity.
You can download userspace tools from
<http://sowerbutts.com/powermate/>.
To compile this driver as a module, choose M here: the
module will be called powermate.
config USB_MTOUCH
tristate "MicroTouch USB Touchscreen Driver"
depends on USB && INPUT
---help---
Say Y here if you want to use a MicroTouch (Now 3M) USB
Touchscreen controller.
See <file:Documentation/usb/mtouch.txt> for additional information.
To compile this driver as a module, choose M here: the
module will be called mtouchusb.
config USB_ITMTOUCH
tristate "ITM Touch USB Touchscreen Driver"
depends on USB && INPUT
---help---
Say Y here if you want to use a ITM Touch USB
Touchscreen controller.
This touchscreen is used in LG 1510SF monitors.
To compile this driver as a module, choose M here: the
module will be called itmtouch.
config USB_EGALAX
tristate "eGalax TouchKit USB Touchscreen Driver"
depends on USB && INPUT
---help---
Say Y here if you want to use a eGalax TouchKit USB
Touchscreen controller.
The driver has been tested on a Xenarc 700TSV monitor
with eGalax touchscreen.
Have a look at <http://linux.chapter7.ch/touchkit/> for
a usage description and the required user-space stuff.
To compile this driver as a module, choose M here: the
module will be called touchkitusb.
config USB_YEALINK
tristate "Yealink usb-p1k voip phone"
depends on USB && INPUT && EXPERIMENTAL
---help---
Say Y here if you want to enable keyboard and LCD functions of the
Yealink usb-p1k usb phones. The audio part is enabled by the generic
usb sound driver, so you might want to enable that as well.
For information about how to use these additional functions, see
<file:Documentation/input/yealink.txt>.
To compile this driver as a module, choose M here: the module will be
called yealink.
config USB_XPAD
tristate "X-Box gamepad support"
depends on USB && INPUT
---help---
Say Y here if you want to use the X-Box pad with your computer.
Make sure to say Y to "Joystick support" (CONFIG_INPUT_JOYDEV)
and/or "Event interface support" (CONFIG_INPUT_EVDEV) as well.
For information about how to connect the X-Box pad to USB, see
<file:Documentation/input/xpad.txt>.
To compile this driver as a module, choose M here: the
module will be called xpad.
config USB_ATI_REMOTE
tristate "ATI / X10 USB RF remote control"
depends on USB && INPUT
---help---
Say Y here if you want to use an ATI or X10 "Lola" USB remote control.
These are RF remotes with USB receivers.
The ATI remote comes with many of ATI's All-In-Wonder video cards.
The X10 "Lola" remote is available at:
<http://www.x10.com/products/lola_sg1.htm>
This driver provides mouse pointer, left and right mouse buttons,
and maps all the other remote buttons to keypress events.
To compile this driver as a module, choose M here: the module will be
called ati_remote.
config USB_KEYSPAN_REMOTE
tristate "Keyspan DMR USB remote control (EXPERIMENTAL)"
depends on USB && INPUT && EXPERIMENTAL
---help---
Say Y here if you want to use a Keyspan DMR USB remote control.
Currently only the UIA-11 type of receiver has been tested. The tag
on the receiver that connects to the USB port should have a P/N that
will tell you what type of DMR you have. The UIA-10 type is not
supported at this time. This driver maps all buttons to keypress
events.
To compile this driver as a module, choose M here: the module will
be called keyspan_remote.
config USB_APPLETOUCH
tristate "Apple USB Touchpad support"
depends on USB && INPUT
---help---
Say Y here if you want to use an Apple USB Touchpad.
These are the touchpads that can be found on post-February 2005
Apple Powerbooks (prior models have a Synaptics touchpad connected
to the ADB bus).
This driver provides a basic mouse driver but can be interfaced
with the synaptics X11 driver to provide acceleration and
scrolling in X11.
For further information, see
<file:Documentation/input/appletouch.txt>.
To compile this driver as a module, choose M here: the
module will be called appletouch.
Reference in New Issue View Git Blame Copy Permalink