kernel-ark/include/scsi/scsi_host.h
Mike Christie 76e4e12ff2 [SCSI] scsi scan: don't fail scans when host is in recovery
The problem is that if we are doing a scsi scan then the device goes
into recovery then we will wait for the recovery to complete. It waits
because scsi-ml will send inquiries or report luns and the queueing code
will have been blocked due to the host not being ready. However, if we
are in recovery and then a scan is started the scan will silently fail
and some devices will not be added.

It is easy to hit the problem where devices do not show up with
FC where we are doing tests that disrupt the target controllers.
When the controller is disruprted (reboot, or setting firmware, etc),
and we cause the dev loss tmo to fire then devices will be removed
Then when the problem has been fixed, the rport will be scanned and
devices should be added back. But if we cause another disruption before
scanning has started then devices will not get added back. If the problem
is not started until the scan is started then the devices will be added
back.

This patch fixes that problem by not failing scans when the host
is in recovery. We will let scsi-ml send the IO and let the queueing
and scsi error handling deal with it like is done if we went into
recovery while scanning.

For recovery cases where the host is being torn down then with the
patch we will still fail the scan since there is not point in scanning.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-29 00:16:19 -07:00

919 lines
28 KiB
C

#ifndef _SCSI_SCSI_HOST_H
#define _SCSI_SCSI_HOST_H
#include <linux/device.h>
#include <linux/list.h>
#include <linux/types.h>
#include <linux/workqueue.h>
#include <linux/mutex.h>
#include <scsi/scsi.h>
struct request_queue;
struct block_device;
struct completion;
struct module;
struct scsi_cmnd;
struct scsi_device;
struct scsi_target;
struct Scsi_Host;
struct scsi_host_cmd_pool;
struct scsi_transport_template;
struct blk_queue_tags;
/*
* The various choices mean:
* NONE: Self evident. Host adapter is not capable of scatter-gather.
* ALL: Means that the host adapter module can do scatter-gather,
* and that there is no limit to the size of the table to which
* we scatter/gather data. The value we set here is the maximum
* single element sglist. To use chained sglists, the adapter
* has to set a value beyond ALL (and correctly use the chain
* handling API.
* Anything else: Indicates the maximum number of chains that can be
* used in one scatter-gather request.
*/
#define SG_NONE 0
#define SG_ALL SCSI_MAX_SG_SEGMENTS
#define MODE_UNKNOWN 0x00
#define MODE_INITIATOR 0x01
#define MODE_TARGET 0x02
#define DISABLE_CLUSTERING 0
#define ENABLE_CLUSTERING 1
enum {
SCSI_QDEPTH_DEFAULT, /* default requested change, e.g. from sysfs */
SCSI_QDEPTH_QFULL, /* scsi-ml requested due to queue full */
SCSI_QDEPTH_RAMP_UP, /* scsi-ml requested due to threshold event */
};
struct scsi_host_template {
struct module *module;
const char *name;
/*
* Used to initialize old-style drivers. For new-style drivers
* just perform all work in your module initialization function.
*
* Status: OBSOLETE
*/
int (* detect)(struct scsi_host_template *);
/*
* Used as unload callback for hosts with old-style drivers.
*
* Status: OBSOLETE
*/
int (* release)(struct Scsi_Host *);
/*
* The info function will return whatever useful information the
* developer sees fit. If not provided, then the name field will
* be used instead.
*
* Status: OPTIONAL
*/
const char *(* info)(struct Scsi_Host *);
/*
* Ioctl interface
*
* Status: OPTIONAL
*/
int (* ioctl)(struct scsi_device *dev, int cmd, void __user *arg);
#ifdef CONFIG_COMPAT
/*
* Compat handler. Handle 32bit ABI.
* When unknown ioctl is passed return -ENOIOCTLCMD.
*
* Status: OPTIONAL
*/
int (* compat_ioctl)(struct scsi_device *dev, int cmd, void __user *arg);
#endif
/*
* The queuecommand function is used to queue up a scsi
* command block to the LLDD. When the driver finished
* processing the command the done callback is invoked.
*
* If queuecommand returns 0, then the HBA has accepted the
* command. The done() function must be called on the command
* when the driver has finished with it. (you may call done on the
* command before queuecommand returns, but in this case you
* *must* return 0 from queuecommand).
*
* Queuecommand may also reject the command, in which case it may
* not touch the command and must not call done() for it.
*
* There are two possible rejection returns:
*
* SCSI_MLQUEUE_DEVICE_BUSY: Block this device temporarily, but
* allow commands to other devices serviced by this host.
*
* SCSI_MLQUEUE_HOST_BUSY: Block all devices served by this
* host temporarily.
*
* For compatibility, any other non-zero return is treated the
* same as SCSI_MLQUEUE_HOST_BUSY.
*
* NOTE: "temporarily" means either until the next command for#
* this device/host completes, or a period of time determined by
* I/O pressure in the system if there are no other outstanding
* commands.
*
* STATUS: REQUIRED
*/
int (* queuecommand)(struct Scsi_Host *, struct scsi_cmnd *);
/*
* The transfer functions are used to queue a scsi command to
* the LLD. When the driver is finished processing the command
* the done callback is invoked.
*
* This is called to inform the LLD to transfer
* scsi_bufflen(cmd) bytes. scsi_sg_count(cmd) speciefies the
* number of scatterlist entried in the command and
* scsi_sglist(cmd) returns the scatterlist.
*
* return values: see queuecommand
*
* If the LLD accepts the cmd, it should set the result to an
* appropriate value when completed before calling the done function.
*
* STATUS: REQUIRED FOR TARGET DRIVERS
*/
/* TODO: rename */
int (* transfer_response)(struct scsi_cmnd *,
void (*done)(struct scsi_cmnd *));
/*
* This is an error handling strategy routine. You don't need to
* define one of these if you don't want to - there is a default
* routine that is present that should work in most cases. For those
* driver authors that have the inclination and ability to write their
* own strategy routine, this is where it is specified. Note - the
* strategy routine is *ALWAYS* run in the context of the kernel eh
* thread. Thus you are guaranteed to *NOT* be in an interrupt
* handler when you execute this, and you are also guaranteed to
* *NOT* have any other commands being queued while you are in the
* strategy routine. When you return from this function, operations
* return to normal.
*
* See scsi_error.c scsi_unjam_host for additional comments about
* what this function should and should not be attempting to do.
*
* Status: REQUIRED (at least one of them)
*/
int (* eh_abort_handler)(struct scsi_cmnd *);
int (* eh_device_reset_handler)(struct scsi_cmnd *);
int (* eh_target_reset_handler)(struct scsi_cmnd *);
int (* eh_bus_reset_handler)(struct scsi_cmnd *);
int (* eh_host_reset_handler)(struct scsi_cmnd *);
/*
* Before the mid layer attempts to scan for a new device where none
* currently exists, it will call this entry in your driver. Should
* your driver need to allocate any structs or perform any other init
* items in order to send commands to a currently unused target/lun
* combo, then this is where you can perform those allocations. This
* is specifically so that drivers won't have to perform any kind of
* "is this a new device" checks in their queuecommand routine,
* thereby making the hot path a bit quicker.
*
* Return values: 0 on success, non-0 on failure
*
* Deallocation: If we didn't find any devices at this ID, you will
* get an immediate call to slave_destroy(). If we find something
* here then you will get a call to slave_configure(), then the
* device will be used for however long it is kept around, then when
* the device is removed from the system (or * possibly at reboot
* time), you will then get a call to slave_destroy(). This is
* assuming you implement slave_configure and slave_destroy.
* However, if you allocate memory and hang it off the device struct,
* then you must implement the slave_destroy() routine at a minimum
* in order to avoid leaking memory
* each time a device is tore down.
*
* Status: OPTIONAL
*/
int (* slave_alloc)(struct scsi_device *);
/*
* Once the device has responded to an INQUIRY and we know the
* device is online, we call into the low level driver with the
* struct scsi_device *. If the low level device driver implements
* this function, it *must* perform the task of setting the queue
* depth on the device. All other tasks are optional and depend
* on what the driver supports and various implementation details.
*
* Things currently recommended to be handled at this time include:
*
* 1. Setting the device queue depth. Proper setting of this is
* described in the comments for scsi_adjust_queue_depth.
* 2. Determining if the device supports the various synchronous
* negotiation protocols. The device struct will already have
* responded to INQUIRY and the results of the standard items
* will have been shoved into the various device flag bits, eg.
* device->sdtr will be true if the device supports SDTR messages.
* 3. Allocating command structs that the device will need.
* 4. Setting the default timeout on this device (if needed).
* 5. Anything else the low level driver might want to do on a device
* specific setup basis...
* 6. Return 0 on success, non-0 on error. The device will be marked
* as offline on error so that no access will occur. If you return
* non-0, your slave_destroy routine will never get called for this
* device, so don't leave any loose memory hanging around, clean
* up after yourself before returning non-0
*
* Status: OPTIONAL
*/
int (* slave_configure)(struct scsi_device *);
/*
* Immediately prior to deallocating the device and after all activity
* has ceased the mid layer calls this point so that the low level
* driver may completely detach itself from the scsi device and vice
* versa. The low level driver is responsible for freeing any memory
* it allocated in the slave_alloc or slave_configure calls.
*
* Status: OPTIONAL
*/
void (* slave_destroy)(struct scsi_device *);
/*
* Before the mid layer attempts to scan for a new device attached
* to a target where no target currently exists, it will call this
* entry in your driver. Should your driver need to allocate any
* structs or perform any other init items in order to send commands
* to a currently unused target, then this is where you can perform
* those allocations.
*
* Return values: 0 on success, non-0 on failure
*
* Status: OPTIONAL
*/
int (* target_alloc)(struct scsi_target *);
/*
* Immediately prior to deallocating the target structure, and
* after all activity to attached scsi devices has ceased, the
* midlayer calls this point so that the driver may deallocate
* and terminate any references to the target.
*
* Status: OPTIONAL
*/
void (* target_destroy)(struct scsi_target *);
/*
* If a host has the ability to discover targets on its own instead
* of scanning the entire bus, it can fill in this function and
* call scsi_scan_host(). This function will be called periodically
* until it returns 1 with the scsi_host and the elapsed time of
* the scan in jiffies.
*
* Status: OPTIONAL
*/
int (* scan_finished)(struct Scsi_Host *, unsigned long);
/*
* If the host wants to be called before the scan starts, but
* after the midlayer has set up ready for the scan, it can fill
* in this function.
*
* Status: OPTIONAL
*/
void (* scan_start)(struct Scsi_Host *);
/*
* Fill in this function to allow the queue depth of this host
* to be changeable (on a per device basis). Returns either
* the current queue depth setting (may be different from what
* was passed in) or an error. An error should only be
* returned if the requested depth is legal but the driver was
* unable to set it. If the requested depth is illegal, the
* driver should set and return the closest legal queue depth.
*
* Status: OPTIONAL
*/
int (* change_queue_depth)(struct scsi_device *, int, int);
/*
* Fill in this function to allow the changing of tag types
* (this also allows the enabling/disabling of tag command
* queueing). An error should only be returned if something
* went wrong in the driver while trying to set the tag type.
* If the driver doesn't support the requested tag type, then
* it should set the closest type it does support without
* returning an error. Returns the actual tag type set.
*
* Status: OPTIONAL
*/
int (* change_queue_type)(struct scsi_device *, int);
/*
* This function determines the BIOS parameters for a given
* harddisk. These tend to be numbers that are made up by
* the host adapter. Parameters:
* size, device, list (heads, sectors, cylinders)
*
* Status: OPTIONAL
*/
int (* bios_param)(struct scsi_device *, struct block_device *,
sector_t, int []);
/*
* This function is called when one or more partitions on the
* device reach beyond the end of the device.
*
* Status: OPTIONAL
*/
void (*unlock_native_capacity)(struct scsi_device *);
/*
* Can be used to export driver statistics and other infos to the
* world outside the kernel ie. userspace and it also provides an
* interface to feed the driver with information.
*
* Status: OBSOLETE
*/
int (*proc_info)(struct Scsi_Host *, char *, char **, off_t, int, int);
/*
* This is an optional routine that allows the transport to become
* involved when a scsi io timer fires. The return value tells the
* timer routine how to finish the io timeout handling:
* EH_HANDLED: I fixed the error, please complete the command
* EH_RESET_TIMER: I need more time, reset the timer and
* begin counting again
* EH_NOT_HANDLED Begin normal error recovery
*
* Status: OPTIONAL
*/
enum blk_eh_timer_return (*eh_timed_out)(struct scsi_cmnd *);
/* This is an optional routine that allows transport to initiate
* LLD adapter or firmware reset using sysfs attribute.
*
* Return values: 0 on success, -ve value on failure.
*
* Status: OPTIONAL
*/
int (*host_reset)(struct Scsi_Host *shost, int reset_type);
#define SCSI_ADAPTER_RESET 1
#define SCSI_FIRMWARE_RESET 2
/*
* Name of proc directory
*/
const char *proc_name;
/*
* Used to store the procfs directory if a driver implements the
* proc_info method.
*/
struct proc_dir_entry *proc_dir;
/*
* This determines if we will use a non-interrupt driven
* or an interrupt driven scheme. It is set to the maximum number
* of simultaneous commands a given host adapter will accept.
*/
int can_queue;
/*
* In many instances, especially where disconnect / reconnect are
* supported, our host also has an ID on the SCSI bus. If this is
* the case, then it must be reserved. Please set this_id to -1 if
* your setup is in single initiator mode, and the host lacks an
* ID.
*/
int this_id;
/*
* This determines the degree to which the host adapter is capable
* of scatter-gather.
*/
unsigned short sg_tablesize;
unsigned short sg_prot_tablesize;
/*
* Set this if the host adapter has limitations beside segment count.
*/
unsigned short max_sectors;
/*
* DMA scatter gather segment boundary limit. A segment crossing this
* boundary will be split in two.
*/
unsigned long dma_boundary;
/*
* This specifies "machine infinity" for host templates which don't
* limit the transfer size. Note this limit represents an absolute
* maximum, and may be over the transfer limits allowed for
* individual devices (e.g. 256 for SCSI-1).
*/
#define SCSI_DEFAULT_MAX_SECTORS 1024
/*
* True if this host adapter can make good use of linked commands.
* This will allow more than one command to be queued to a given
* unit on a given host. Set this to the maximum number of command
* blocks to be provided for each device. Set this to 1 for one
* command block per lun, 2 for two, etc. Do not set this to 0.
* You should make sure that the host adapter will do the right thing
* before you try setting this above 1.
*/
short cmd_per_lun;
/*
* present contains counter indicating how many boards of this
* type were found when we did the scan.
*/
unsigned char present;
/*
* This specifies the mode that a LLD supports.
*/
unsigned supported_mode:2;
/*
* True if this host adapter uses unchecked DMA onto an ISA bus.
*/
unsigned unchecked_isa_dma:1;
/*
* True if this host adapter can make good use of clustering.
* I originally thought that if the tablesize was large that it
* was a waste of CPU cycles to prepare a cluster list, but
* it works out that the Buslogic is faster if you use a smaller
* number of segments (i.e. use clustering). I guess it is
* inefficient.
*/
unsigned use_clustering:1;
/*
* True for emulated SCSI host adapters (e.g. ATAPI).
*/
unsigned emulated:1;
/*
* True if the low-level driver performs its own reset-settle delays.
*/
unsigned skip_settle_delay:1;
/*
* True if we are using ordered write support.
*/
unsigned ordered_tag:1;
/*
* Countdown for host blocking with no commands outstanding.
*/
unsigned int max_host_blocked;
/*
* Default value for the blocking. If the queue is empty,
* host_blocked counts down in the request_fn until it restarts
* host operations as zero is reached.
*
* FIXME: This should probably be a value in the template
*/
#define SCSI_DEFAULT_HOST_BLOCKED 7
/*
* Pointer to the sysfs class properties for this host, NULL terminated.
*/
struct device_attribute **shost_attrs;
/*
* Pointer to the SCSI device properties for this host, NULL terminated.
*/
struct device_attribute **sdev_attrs;
/*
* List of hosts per template.
*
* This is only for use by scsi_module.c for legacy templates.
* For these access to it is synchronized implicitly by
* module_init/module_exit.
*/
struct list_head legacy_hosts;
/*
* Vendor Identifier associated with the host
*
* Note: When specifying vendor_id, be sure to read the
* Vendor Type and ID formatting requirements specified in
* scsi_netlink.h
*/
u64 vendor_id;
};
/*
* Temporary #define for host lock push down. Can be removed when all
* drivers have been updated to take advantage of unlocked
* queuecommand.
*
*/
#define DEF_SCSI_QCMD(func_name) \
int func_name(struct Scsi_Host *shost, struct scsi_cmnd *cmd) \
{ \
unsigned long irq_flags; \
int rc; \
spin_lock_irqsave(shost->host_lock, irq_flags); \
scsi_cmd_get_serial(shost, cmd); \
rc = func_name##_lck (cmd, cmd->scsi_done); \
spin_unlock_irqrestore(shost->host_lock, irq_flags); \
return rc; \
}
/*
* shost state: If you alter this, you also need to alter scsi_sysfs.c
* (for the ascii descriptions) and the state model enforcer:
* scsi_host_set_state()
*/
enum scsi_host_state {
SHOST_CREATED = 1,
SHOST_RUNNING,
SHOST_CANCEL,
SHOST_DEL,
SHOST_RECOVERY,
SHOST_CANCEL_RECOVERY,
SHOST_DEL_RECOVERY,
};
struct Scsi_Host {
/*
* __devices is protected by the host_lock, but you should
* usually use scsi_device_lookup / shost_for_each_device
* to access it and don't care about locking yourself.
* In the rare case of beeing in irq context you can use
* their __ prefixed variants with the lock held. NEVER
* access this list directly from a driver.
*/
struct list_head __devices;
struct list_head __targets;
struct scsi_host_cmd_pool *cmd_pool;
spinlock_t free_list_lock;
struct list_head free_list; /* backup store of cmd structs */
struct list_head starved_list;
spinlock_t default_lock;
spinlock_t *host_lock;
struct mutex scan_mutex;/* serialize scanning activity */
struct list_head eh_cmd_q;
struct task_struct * ehandler; /* Error recovery thread. */
struct completion * eh_action; /* Wait for specific actions on the
host. */
wait_queue_head_t host_wait;
struct scsi_host_template *hostt;
struct scsi_transport_template *transportt;
/*
* Area to keep a shared tag map (if needed, will be
* NULL if not).
*/
struct blk_queue_tag *bqt;
/*
* The following two fields are protected with host_lock;
* however, eh routines can safely access during eh processing
* without acquiring the lock.
*/
unsigned int host_busy; /* commands actually active on low-level */
unsigned int host_failed; /* commands that failed. */
unsigned int host_eh_scheduled; /* EH scheduled without command */
unsigned int host_no; /* Used for IOCTL_GET_IDLUN, /proc/scsi et al. */
int resetting; /* if set, it means that last_reset is a valid value */
unsigned long last_reset;
/*
* These three parameters can be used to allow for wide scsi,
* and for host adapters that support multiple busses
* The first two should be set to 1 more than the actual max id
* or lun (i.e. 8 for normal systems).
*/
unsigned int max_id;
unsigned int max_lun;
unsigned int max_channel;
/*
* This is a unique identifier that must be assigned so that we
* have some way of identifying each detected host adapter properly
* and uniquely. For hosts that do not support more than one card
* in the system at one time, this does not need to be set. It is
* initialized to 0 in scsi_register.
*/
unsigned int unique_id;
/*
* The maximum length of SCSI commands that this host can accept.
* Probably 12 for most host adapters, but could be 16 for others.
* or 260 if the driver supports variable length cdbs.
* For drivers that don't set this field, a value of 12 is
* assumed.
*/
unsigned short max_cmd_len;
int this_id;
int can_queue;
short cmd_per_lun;
short unsigned int sg_tablesize;
short unsigned int sg_prot_tablesize;
short unsigned int max_sectors;
unsigned long dma_boundary;
/*
* Used to assign serial numbers to the cmds.
* Protected by the host lock.
*/
unsigned long cmd_serial_number;
unsigned active_mode:2;
unsigned unchecked_isa_dma:1;
unsigned use_clustering:1;
unsigned use_blk_tcq:1;
/*
* Host has requested that no further requests come through for the
* time being.
*/
unsigned host_self_blocked:1;
/*
* Host uses correct SCSI ordering not PC ordering. The bit is
* set for the minority of drivers whose authors actually read
* the spec ;).
*/
unsigned reverse_ordering:1;
/*
* Ordered write support
*/
unsigned ordered_tag:1;
/* Task mgmt function in progress */
unsigned tmf_in_progress:1;
/* Asynchronous scan in progress */
unsigned async_scan:1;
/*
* Optional work queue to be utilized by the transport
*/
char work_q_name[20];
struct workqueue_struct *work_q;
/*
* Host has rejected a command because it was busy.
*/
unsigned int host_blocked;
/*
* Value host_blocked counts down from
*/
unsigned int max_host_blocked;
/* Protection Information */
unsigned int prot_capabilities;
unsigned char prot_guard_type;
/*
* q used for scsi_tgt msgs, async events or any other requests that
* need to be processed in userspace
*/
struct request_queue *uspace_req_q;
/* legacy crap */
unsigned long base;
unsigned long io_port;
unsigned char n_io_port;
unsigned char dma_channel;
unsigned int irq;
enum scsi_host_state shost_state;
/* ldm bits */
struct device shost_gendev, shost_dev;
/*
* List of hosts per template.
*
* This is only for use by scsi_module.c for legacy templates.
* For these access to it is synchronized implicitly by
* module_init/module_exit.
*/
struct list_head sht_legacy_list;
/*
* Points to the transport data (if any) which is allocated
* separately
*/
void *shost_data;
/*
* Points to the physical bus device we'd use to do DMA
* Needed just in case we have virtual hosts.
*/
struct device *dma_dev;
/*
* We should ensure that this is aligned, both for better performance
* and also because some compilers (m68k) don't automatically force
* alignment to a long boundary.
*/
unsigned long hostdata[0] /* Used for storage of host specific stuff */
__attribute__ ((aligned (sizeof(unsigned long))));
};
#define class_to_shost(d) \
container_of(d, struct Scsi_Host, shost_dev)
#define shost_printk(prefix, shost, fmt, a...) \
dev_printk(prefix, &(shost)->shost_gendev, fmt, ##a)
static inline void *shost_priv(struct Scsi_Host *shost)
{
return (void *)shost->hostdata;
}
int scsi_is_host_device(const struct device *);
static inline struct Scsi_Host *dev_to_shost(struct device *dev)
{
while (!scsi_is_host_device(dev)) {
if (!dev->parent)
return NULL;
dev = dev->parent;
}
return container_of(dev, struct Scsi_Host, shost_gendev);
}
static inline int scsi_host_in_recovery(struct Scsi_Host *shost)
{
return shost->shost_state == SHOST_RECOVERY ||
shost->shost_state == SHOST_CANCEL_RECOVERY ||
shost->shost_state == SHOST_DEL_RECOVERY ||
shost->tmf_in_progress;
}
extern int scsi_queue_work(struct Scsi_Host *, struct work_struct *);
extern void scsi_flush_work(struct Scsi_Host *);
extern struct Scsi_Host *scsi_host_alloc(struct scsi_host_template *, int);
extern int __must_check scsi_add_host_with_dma(struct Scsi_Host *,
struct device *,
struct device *);
extern void scsi_scan_host(struct Scsi_Host *);
extern void scsi_rescan_device(struct device *);
extern void scsi_remove_host(struct Scsi_Host *);
extern struct Scsi_Host *scsi_host_get(struct Scsi_Host *);
extern void scsi_host_put(struct Scsi_Host *t);
extern struct Scsi_Host *scsi_host_lookup(unsigned short);
extern const char *scsi_host_state_name(enum scsi_host_state);
extern void scsi_cmd_get_serial(struct Scsi_Host *, struct scsi_cmnd *);
extern u64 scsi_calculate_bounce_limit(struct Scsi_Host *);
static inline int __must_check scsi_add_host(struct Scsi_Host *host,
struct device *dev)
{
return scsi_add_host_with_dma(host, dev, dev);
}
static inline struct device *scsi_get_device(struct Scsi_Host *shost)
{
return shost->shost_gendev.parent;
}
/**
* scsi_host_scan_allowed - Is scanning of this host allowed
* @shost: Pointer to Scsi_Host.
**/
static inline int scsi_host_scan_allowed(struct Scsi_Host *shost)
{
return shost->shost_state == SHOST_RUNNING ||
shost->shost_state == SHOST_RECOVERY;
}
extern void scsi_unblock_requests(struct Scsi_Host *);
extern void scsi_block_requests(struct Scsi_Host *);
struct class_container;
extern struct request_queue *__scsi_alloc_queue(struct Scsi_Host *shost,
void (*) (struct request_queue *));
/*
* These two functions are used to allocate and free a pseudo device
* which will connect to the host adapter itself rather than any
* physical device. You must deallocate when you are done with the
* thing. This physical pseudo-device isn't real and won't be available
* from any high-level drivers.
*/
extern void scsi_free_host_dev(struct scsi_device *);
extern struct scsi_device *scsi_get_host_dev(struct Scsi_Host *);
/*
* DIF defines the exchange of protection information between
* initiator and SBC block device.
*
* DIX defines the exchange of protection information between OS and
* initiator.
*/
enum scsi_host_prot_capabilities {
SHOST_DIF_TYPE1_PROTECTION = 1 << 0, /* T10 DIF Type 1 */
SHOST_DIF_TYPE2_PROTECTION = 1 << 1, /* T10 DIF Type 2 */
SHOST_DIF_TYPE3_PROTECTION = 1 << 2, /* T10 DIF Type 3 */
SHOST_DIX_TYPE0_PROTECTION = 1 << 3, /* DIX between OS and HBA only */
SHOST_DIX_TYPE1_PROTECTION = 1 << 4, /* DIX with DIF Type 1 */
SHOST_DIX_TYPE2_PROTECTION = 1 << 5, /* DIX with DIF Type 2 */
SHOST_DIX_TYPE3_PROTECTION = 1 << 6, /* DIX with DIF Type 3 */
};
/*
* SCSI hosts which support the Data Integrity Extensions must
* indicate their capabilities by setting the prot_capabilities using
* this call.
*/
static inline void scsi_host_set_prot(struct Scsi_Host *shost, unsigned int mask)
{
shost->prot_capabilities = mask;
}
static inline unsigned int scsi_host_get_prot(struct Scsi_Host *shost)
{
return shost->prot_capabilities;
}
static inline int scsi_host_prot_dma(struct Scsi_Host *shost)
{
return shost->prot_capabilities >= SHOST_DIX_TYPE0_PROTECTION;
}
static inline unsigned int scsi_host_dif_capable(struct Scsi_Host *shost, unsigned int target_type)
{
static unsigned char cap[] = { 0,
SHOST_DIF_TYPE1_PROTECTION,
SHOST_DIF_TYPE2_PROTECTION,
SHOST_DIF_TYPE3_PROTECTION };
return shost->prot_capabilities & cap[target_type] ? target_type : 0;
}
static inline unsigned int scsi_host_dix_capable(struct Scsi_Host *shost, unsigned int target_type)
{
#if defined(CONFIG_BLK_DEV_INTEGRITY)
static unsigned char cap[] = { SHOST_DIX_TYPE0_PROTECTION,
SHOST_DIX_TYPE1_PROTECTION,
SHOST_DIX_TYPE2_PROTECTION,
SHOST_DIX_TYPE3_PROTECTION };
return shost->prot_capabilities & cap[target_type];
#endif
return 0;
}
/*
* All DIX-capable initiators must support the T10-mandated CRC
* checksum. Controllers can optionally implement the IP checksum
* scheme which has much lower impact on system performance. Note
* that the main rationale for the checksum is to match integrity
* metadata with data. Detecting bit errors are a job for ECC memory
* and buses.
*/
enum scsi_host_guard_type {
SHOST_DIX_GUARD_CRC = 1 << 0,
SHOST_DIX_GUARD_IP = 1 << 1,
};
static inline void scsi_host_set_guard(struct Scsi_Host *shost, unsigned char type)
{
shost->prot_guard_type = type;
}
static inline unsigned char scsi_host_get_guard(struct Scsi_Host *shost)
{
return shost->prot_guard_type;
}
/* legacy interfaces */
extern struct Scsi_Host *scsi_register(struct scsi_host_template *, int);
extern void scsi_unregister(struct Scsi_Host *);
extern int scsi_host_set_state(struct Scsi_Host *, enum scsi_host_state);
#endif /* _SCSI_SCSI_HOST_H */