kernel-ark/arch/arm/mach-omap1/board-ams-delta.c
Tony Lindgren 3e9a6321f9 This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
 closer to ARM common zImage support.
 
 To avoid a huge amount of trivial merge conflicts with includes,
 this branch is based on several small topic branches coordinated
 with the driver subsystem maintainers. These branches are based on
 v3.7-rc1 and can also be merged into the related driver subsystem
 branches as needed:
 
 omap-for-v3.8/cleanup-headers-prepare   few trivial driver changes
 omap-for-v3.8/cleanup-headers-dma       move of the DMA header
 omap-for-v3.8/cleanup-headers-gpmc      GPMC and MTD changes
 omap-for-v3.8/cleanup-headers-mmc       MMC related changes
 omap-for-v3.8/cleanup-headers-dss       DSS related changes
 omap-for-v3.8/cleanup-headers-asoc      ASoC related changes
 
 Note that for the dma-omap.h, it was decided that it should be
 is completed. For the related discussion, please see:
 
 https://patchwork.kernel.org/patch/1519591/#
 
 After these patches we still have a few plat headers remaining
 that will be handled in later pull requests.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQgLn6AAoJEBvUPslcq6VztJIQAMDLmUr4XRa0pV9ASPieMSnP
 LqXQ8Gpr8JP6I2A7mjj5K/PVvU2PCIgefX5/F7PssWeDzPs1p6T5eQc6/Oo88j+k
 6xIaPJtuU6aiMKiH4QJBU9mfFZN4tvKNX8sJZ4YhzAmkKshwSd2XdWQlkSWYV7Ii
 QFRXOdYdX3dgvt3Pv5LYhFMlRDzXlMtCNkdyO0C5yDc038FvT5kxcgpOJ99ndX1F
 aSpNPchDwEXP7WZl3O7uZs732hRHQbKraMkzalVJ5mgvLSwF7VsB+BLdjOgRqFfg
 edpAPt/izpTk7cg7RQiItrW3xz3eSiN/fiAg2wLvxr6ewzB5DguPLa6DNPF+uyup
 BlpQAvNsICIixfKb/qimQBOkB71TTRxqvBnG0Vt/cExS1dTuWlhyCYzA6dhZtl+w
 7ETCo7Mmj+L9T1EfzhMPgjWvMZ4Luli4NHSUYxMl5Cs8nu1y6ytIXxH9e0mnZAbK
 n4ANoIuFE3ZueXWnHAVCOs0YZj2F1OLB+mFkIFg3OVpB4WCXiOTgJuDNsAAQNS3/
 VsYVehNFRB/E/lMWkN293j95LRSwl/sIKbvlpxe7M3XQi4IWh1bDPwcg1YhGPxRV
 HIuQSSMIIzcsFoDqbQYv9qzpvslfee58fBV0L8BzMyXNd1lYzWJ5Af6A8ddSVVFS
 Hh+btZObC1zP/2IKbImk
 =HUTj
 -----END PGP SIGNATURE-----

Merge tag 'omap-for-v3.8/cleanup-headers-signed' into omap-for-v3.8/cleanup-headers-serial-take2

This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.

To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:

omap-for-v3.8/cleanup-headers-prepare   few trivial driver changes
omap-for-v3.8/cleanup-headers-dma       move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc      GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc       MMC related changes
omap-for-v3.8/cleanup-headers-dss       DSS related changes
omap-for-v3.8/cleanup-headers-asoc      ASoC related changes

Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:

https://patchwork.kernel.org/patch/1519591/#

After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
2012-10-24 13:25:44 -07:00

634 lines
14 KiB
C

/*
* linux/arch/arm/mach-omap1/board-ams-delta.c
*
* Modified from board-generic.c
*
* Board specific inits for the Amstrad E3 (codename Delta) videophone
*
* Copyright (C) 2006 Jonathan McDowell <noodles@earth.li>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/basic_mmio_gpio.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <linux/interrupt.h>
#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/regulator/consumer.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/serial_8250.h>
#include <linux/export.h>
#include <linux/omapfb.h>
#include <linux/io.h>
#include <linux/platform_data/gpio-omap.h>
#include <media/soc_camera.h>
#include <asm/serial.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <mach/board-ams-delta.h>
#include <linux/platform_data/keypad-omap.h>
#include <mach/mux.h>
#include <mach/hardware.h>
#include <mach/ams-delta-fiq.h>
#include <mach/camera.h>
#include <mach/usb.h>
#include "iomap.h"
#include "common.h"
static const unsigned int ams_delta_keymap[] = {
KEY(0, 0, KEY_F1), /* Advert */
KEY(0, 3, KEY_COFFEE), /* Games */
KEY(0, 2, KEY_QUESTION), /* Directory */
KEY(2, 3, KEY_CONNECT), /* Internet */
KEY(1, 2, KEY_SHOP), /* Services */
KEY(1, 1, KEY_PHONE), /* VoiceMail */
KEY(0, 1, KEY_DELETE), /* Delete */
KEY(2, 2, KEY_PLAY), /* Play */
KEY(1, 0, KEY_PAGEUP), /* Up */
KEY(1, 3, KEY_PAGEDOWN), /* Down */
KEY(2, 0, KEY_EMAIL), /* ReadEmail */
KEY(2, 1, KEY_STOP), /* Stop */
/* Numeric keypad portion */
KEY(0, 7, KEY_KP1),
KEY(0, 6, KEY_KP2),
KEY(0, 5, KEY_KP3),
KEY(1, 7, KEY_KP4),
KEY(1, 6, KEY_KP5),
KEY(1, 5, KEY_KP6),
KEY(2, 7, KEY_KP7),
KEY(2, 6, KEY_KP8),
KEY(2, 5, KEY_KP9),
KEY(3, 6, KEY_KP0),
KEY(3, 7, KEY_KPASTERISK),
KEY(3, 5, KEY_KPDOT), /* # key */
KEY(7, 2, KEY_NUMLOCK), /* Mute */
KEY(7, 1, KEY_KPMINUS), /* Recall */
KEY(6, 1, KEY_KPPLUS), /* Redial */
KEY(7, 6, KEY_KPSLASH), /* Handsfree */
KEY(6, 0, KEY_ENTER), /* Video */
KEY(7, 4, KEY_CAMERA), /* Photo */
KEY(0, 4, KEY_F2), /* Home */
KEY(1, 4, KEY_F3), /* Office */
KEY(2, 4, KEY_F4), /* Mobile */
KEY(7, 7, KEY_F5), /* SMS */
KEY(7, 5, KEY_F6), /* Email */
/* QWERTY portion of keypad */
KEY(3, 4, KEY_Q),
KEY(3, 3, KEY_W),
KEY(3, 2, KEY_E),
KEY(3, 1, KEY_R),
KEY(3, 0, KEY_T),
KEY(4, 7, KEY_Y),
KEY(4, 6, KEY_U),
KEY(4, 5, KEY_I),
KEY(4, 4, KEY_O),
KEY(4, 3, KEY_P),
KEY(4, 2, KEY_A),
KEY(4, 1, KEY_S),
KEY(4, 0, KEY_D),
KEY(5, 7, KEY_F),
KEY(5, 6, KEY_G),
KEY(5, 5, KEY_H),
KEY(5, 4, KEY_J),
KEY(5, 3, KEY_K),
KEY(5, 2, KEY_L),
KEY(5, 1, KEY_Z),
KEY(5, 0, KEY_X),
KEY(6, 7, KEY_C),
KEY(6, 6, KEY_V),
KEY(6, 5, KEY_B),
KEY(6, 4, KEY_N),
KEY(6, 3, KEY_M),
KEY(6, 2, KEY_SPACE),
KEY(7, 0, KEY_LEFTSHIFT), /* Vol up */
KEY(7, 3, KEY_LEFTCTRL), /* Vol down */
};
#define LATCH1_PHYS 0x01000000
#define LATCH1_VIRT 0xEA000000
#define MODEM_PHYS 0x04000000
#define MODEM_VIRT 0xEB000000
#define LATCH2_PHYS 0x08000000
#define LATCH2_VIRT 0xEC000000
static struct map_desc ams_delta_io_desc[] __initdata = {
/* AMS_DELTA_LATCH1 */
{
.virtual = LATCH1_VIRT,
.pfn = __phys_to_pfn(LATCH1_PHYS),
.length = 0x01000000,
.type = MT_DEVICE
},
/* AMS_DELTA_LATCH2 */
{
.virtual = LATCH2_VIRT,
.pfn = __phys_to_pfn(LATCH2_PHYS),
.length = 0x01000000,
.type = MT_DEVICE
},
/* AMS_DELTA_MODEM */
{
.virtual = MODEM_VIRT,
.pfn = __phys_to_pfn(MODEM_PHYS),
.length = 0x01000000,
.type = MT_DEVICE
}
};
static struct omap_lcd_config ams_delta_lcd_config __initdata = {
.ctrl_name = "internal",
};
static struct omap_usb_config ams_delta_usb_config = {
.register_host = 1,
.hmc_mode = 16,
.pins[0] = 2,
};
#define LATCH1_GPIO_BASE 232
#define LATCH1_NGPIO 8
static struct resource latch1_resources[] = {
[0] = {
.name = "dat",
.start = LATCH1_PHYS,
.end = LATCH1_PHYS + (LATCH1_NGPIO - 1) / 8,
.flags = IORESOURCE_MEM,
},
};
static struct bgpio_pdata latch1_pdata = {
.base = LATCH1_GPIO_BASE,
.ngpio = LATCH1_NGPIO,
};
static struct platform_device latch1_gpio_device = {
.name = "basic-mmio-gpio",
.id = 0,
.resource = latch1_resources,
.num_resources = ARRAY_SIZE(latch1_resources),
.dev = {
.platform_data = &latch1_pdata,
},
};
static struct resource latch2_resources[] = {
[0] = {
.name = "dat",
.start = LATCH2_PHYS,
.end = LATCH2_PHYS + (AMS_DELTA_LATCH2_NGPIO - 1) / 8,
.flags = IORESOURCE_MEM,
},
};
static struct bgpio_pdata latch2_pdata = {
.base = AMS_DELTA_LATCH2_GPIO_BASE,
.ngpio = AMS_DELTA_LATCH2_NGPIO,
};
static struct platform_device latch2_gpio_device = {
.name = "basic-mmio-gpio",
.id = 1,
.resource = latch2_resources,
.num_resources = ARRAY_SIZE(latch2_resources),
.dev = {
.platform_data = &latch2_pdata,
},
};
static const struct gpio latch_gpios[] __initconst = {
{
.gpio = LATCH1_GPIO_BASE + 6,
.flags = GPIOF_OUT_INIT_LOW,
.label = "dockit1",
},
{
.gpio = LATCH1_GPIO_BASE + 7,
.flags = GPIOF_OUT_INIT_LOW,
.label = "dockit2",
},
{
.gpio = AMS_DELTA_GPIO_PIN_SCARD_RSTIN,
.flags = GPIOF_OUT_INIT_LOW,
.label = "scard_rstin",
},
{
.gpio = AMS_DELTA_GPIO_PIN_SCARD_CMDVCC,
.flags = GPIOF_OUT_INIT_LOW,
.label = "scard_cmdvcc",
},
{
.gpio = AMS_DELTA_GPIO_PIN_MODEM_CODEC,
.flags = GPIOF_OUT_INIT_LOW,
.label = "modem_codec",
},
{
.gpio = AMS_DELTA_LATCH2_GPIO_BASE + 14,
.flags = GPIOF_OUT_INIT_LOW,
.label = "hookflash1",
},
{
.gpio = AMS_DELTA_LATCH2_GPIO_BASE + 15,
.flags = GPIOF_OUT_INIT_LOW,
.label = "hookflash2",
},
};
static struct regulator_consumer_supply modem_nreset_consumers[] = {
REGULATOR_SUPPLY("RESET#", "serial8250.1"),
REGULATOR_SUPPLY("POR", "cx20442-codec"),
};
static struct regulator_init_data modem_nreset_data = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
.boot_on = 1,
},
.num_consumer_supplies = ARRAY_SIZE(modem_nreset_consumers),
.consumer_supplies = modem_nreset_consumers,
};
static struct fixed_voltage_config modem_nreset_config = {
.supply_name = "modem_nreset",
.microvolts = 3300000,
.gpio = AMS_DELTA_GPIO_PIN_MODEM_NRESET,
.startup_delay = 25000,
.enable_high = 1,
.enabled_at_boot = 1,
.init_data = &modem_nreset_data,
};
static struct platform_device modem_nreset_device = {
.name = "reg-fixed-voltage",
.id = -1,
.dev = {
.platform_data = &modem_nreset_config,
},
};
struct modem_private_data {
struct regulator *regulator;
};
static struct modem_private_data modem_priv;
void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value)
{
int bit = 0;
u16 bitpos = 1 << bit;
for (; bit < ngpio; bit++, bitpos = bitpos << 1) {
if (!(mask & bitpos))
continue;
else
gpio_set_value(base + bit, (value & bitpos) != 0);
}
}
EXPORT_SYMBOL(ams_delta_latch_write);
static struct resource ams_delta_nand_resources[] = {
[0] = {
.start = OMAP1_MPUIO_BASE,
.end = OMAP1_MPUIO_BASE +
OMAP_MPUIO_IO_CNTL + sizeof(u32) - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device ams_delta_nand_device = {
.name = "ams-delta-nand",
.id = -1,
.num_resources = ARRAY_SIZE(ams_delta_nand_resources),
.resource = ams_delta_nand_resources,
};
static struct resource ams_delta_kp_resources[] = {
[0] = {
.start = INT_KEYBOARD,
.end = INT_KEYBOARD,
.flags = IORESOURCE_IRQ,
},
};
static const struct matrix_keymap_data ams_delta_keymap_data = {
.keymap = ams_delta_keymap,
.keymap_size = ARRAY_SIZE(ams_delta_keymap),
};
static struct omap_kp_platform_data ams_delta_kp_data = {
.rows = 8,
.cols = 8,
.keymap_data = &ams_delta_keymap_data,
.delay = 9,
};
static struct platform_device ams_delta_kp_device = {
.name = "omap-keypad",
.id = -1,
.dev = {
.platform_data = &ams_delta_kp_data,
},
.num_resources = ARRAY_SIZE(ams_delta_kp_resources),
.resource = ams_delta_kp_resources,
};
static struct platform_device ams_delta_lcd_device = {
.name = "lcd_ams_delta",
.id = -1,
};
static const struct gpio_led gpio_leds[] __initconst = {
{
.name = "camera",
.gpio = LATCH1_GPIO_BASE + 0,
.default_state = LEDS_GPIO_DEFSTATE_OFF,
#ifdef CONFIG_LEDS_TRIGGERS
.default_trigger = "ams_delta_camera",
#endif
},
{
.name = "advert",
.gpio = LATCH1_GPIO_BASE + 1,
.default_state = LEDS_GPIO_DEFSTATE_OFF,
},
{
.name = "email",
.gpio = LATCH1_GPIO_BASE + 2,
.default_state = LEDS_GPIO_DEFSTATE_OFF,
},
{
.name = "handsfree",
.gpio = LATCH1_GPIO_BASE + 3,
.default_state = LEDS_GPIO_DEFSTATE_OFF,
},
{
.name = "voicemail",
.gpio = LATCH1_GPIO_BASE + 4,
.default_state = LEDS_GPIO_DEFSTATE_OFF,
},
{
.name = "voice",
.gpio = LATCH1_GPIO_BASE + 5,
.default_state = LEDS_GPIO_DEFSTATE_OFF,
},
};
static const struct gpio_led_platform_data leds_pdata __initconst = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct i2c_board_info ams_delta_camera_board_info[] = {
{
I2C_BOARD_INFO("ov6650", 0x60),
},
};
#ifdef CONFIG_LEDS_TRIGGERS
DEFINE_LED_TRIGGER(ams_delta_camera_led_trigger);
static int ams_delta_camera_power(struct device *dev, int power)
{
/*
* turn on camera LED
*/
if (power)
led_trigger_event(ams_delta_camera_led_trigger, LED_FULL);
else
led_trigger_event(ams_delta_camera_led_trigger, LED_OFF);
return 0;
}
#else
#define ams_delta_camera_power NULL
#endif
static struct soc_camera_link ams_delta_iclink = {
.bus_id = 0, /* OMAP1 SoC camera bus */
.i2c_adapter_id = 1,
.board_info = &ams_delta_camera_board_info[0],
.module_name = "ov6650",
.power = ams_delta_camera_power,
};
static struct platform_device ams_delta_camera_device = {
.name = "soc-camera-pdrv",
.id = 0,
.dev = {
.platform_data = &ams_delta_iclink,
},
};
static struct omap1_cam_platform_data ams_delta_camera_platform_data = {
.camexclk_khz = 12000, /* default 12MHz clock, no extra DPLL */
.lclk_khz_max = 1334, /* results in 5fps CIF, 10fps QCIF */
};
static struct platform_device ams_delta_audio_device = {
.name = "ams-delta-audio",
.id = -1,
};
static struct platform_device cx20442_codec_device = {
.name = "cx20442-codec",
.id = -1,
};
static struct platform_device *ams_delta_devices[] __initdata = {
&latch1_gpio_device,
&latch2_gpio_device,
&ams_delta_kp_device,
&ams_delta_camera_device,
&ams_delta_audio_device,
};
static struct platform_device *late_devices[] __initdata = {
&ams_delta_nand_device,
&ams_delta_lcd_device,
&cx20442_codec_device,
};
static void __init ams_delta_init(void)
{
/* mux pins for uarts */
omap_cfg_reg(UART1_TX);
omap_cfg_reg(UART1_RTS);
/* parallel camera interface */
omap_cfg_reg(H19_1610_CAM_EXCLK);
omap_cfg_reg(J15_1610_CAM_LCLK);
omap_cfg_reg(L18_1610_CAM_VS);
omap_cfg_reg(L15_1610_CAM_HS);
omap_cfg_reg(L19_1610_CAM_D0);
omap_cfg_reg(K14_1610_CAM_D1);
omap_cfg_reg(K15_1610_CAM_D2);
omap_cfg_reg(K19_1610_CAM_D3);
omap_cfg_reg(K18_1610_CAM_D4);
omap_cfg_reg(J14_1610_CAM_D5);
omap_cfg_reg(J19_1610_CAM_D6);
omap_cfg_reg(J18_1610_CAM_D7);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
omap1_usb_init(&ams_delta_usb_config);
omap1_set_camera_info(&ams_delta_camera_platform_data);
#ifdef CONFIG_LEDS_TRIGGERS
led_trigger_register_simple("ams_delta_camera",
&ams_delta_camera_led_trigger);
#endif
gpio_led_register_device(-1, &leds_pdata);
platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices));
ams_delta_init_fiq();
omap_writew(omap_readw(ARM_RSTCT1) | 0x0004, ARM_RSTCT1);
omapfb_set_lcd_config(&ams_delta_lcd_config);
}
static void modem_pm(struct uart_port *port, unsigned int state, unsigned old)
{
struct modem_private_data *priv = port->private_data;
if (IS_ERR(priv->regulator))
return;
if (state == old)
return;
if (state == 0)
regulator_enable(priv->regulator);
else if (old == 0)
regulator_disable(priv->regulator);
}
static struct plat_serial8250_port ams_delta_modem_ports[] = {
{
.membase = IOMEM(MODEM_VIRT),
.mapbase = MODEM_PHYS,
.irq = -EINVAL, /* changed later */
.flags = UPF_BOOT_AUTOCONF,
.irqflags = IRQF_TRIGGER_RISING,
.iotype = UPIO_MEM,
.regshift = 1,
.uartclk = BASE_BAUD * 16,
.pm = modem_pm,
.private_data = &modem_priv,
},
{ },
};
static struct platform_device ams_delta_modem_device = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM1,
.dev = {
.platform_data = ams_delta_modem_ports,
},
};
static int __init late_init(void)
{
int err;
if (!machine_is_ams_delta())
return -ENODEV;
err = gpio_request_array(latch_gpios, ARRAY_SIZE(latch_gpios));
if (err) {
pr_err("Couldn't take over latch1/latch2 GPIO pins\n");
return err;
}
platform_add_devices(late_devices, ARRAY_SIZE(late_devices));
err = platform_device_register(&modem_nreset_device);
if (err) {
pr_err("Couldn't register the modem regulator device\n");
return err;
}
omap_cfg_reg(M14_1510_GPIO2);
ams_delta_modem_ports[0].irq =
gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
err = gpio_request(AMS_DELTA_GPIO_PIN_MODEM_IRQ, "modem");
if (err) {
pr_err("Couldn't request gpio pin for modem\n");
return err;
}
gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
/* Initialize the modem_nreset regulator consumer before use */
modem_priv.regulator = ERR_PTR(-ENODEV);
ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_CODEC,
AMS_DELTA_LATCH2_MODEM_CODEC);
err = platform_device_register(&ams_delta_modem_device);
if (err)
goto gpio_free;
/*
* Once the modem device is registered, the modem_nreset
* regulator can be requested on behalf of that device.
*/
modem_priv.regulator = regulator_get(&ams_delta_modem_device.dev,
"RESET#");
if (IS_ERR(modem_priv.regulator)) {
err = PTR_ERR(modem_priv.regulator);
goto unregister;
}
return 0;
unregister:
platform_device_unregister(&ams_delta_modem_device);
gpio_free:
gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
return err;
}
static void __init ams_delta_init_late(void)
{
omap1_init_late();
late_init();
}
static void __init ams_delta_map_io(void)
{
omap15xx_map_io();
iotable_init(ams_delta_io_desc, ARRAY_SIZE(ams_delta_io_desc));
}
MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)")
/* Maintainer: Jonathan McDowell <noodles@earth.li> */
.atag_offset = 0x100,
.map_io = ams_delta_map_io,
.init_early = omap1_init_early,
.init_irq = omap1_init_irq,
.init_machine = ams_delta_init,
.init_late = ams_delta_init_late,
.timer = &omap1_timer,
.restart = omap1_restart,
MACHINE_END