kernel-ark

History

Frederic Weisbecker 280f06774a nohz: Separate out irq exit and idle loop dyntick logic The tick_nohz_stop_sched_tick() function, which tries to delay the next timer tick as long as possible, can be called from two places: - From the idle loop to start the dytick idle mode - From interrupt exit if we have interrupted the dyntick idle mode, so that we reprogram the next tick event in case the irq changed some internal state that requires this action. There are only few minor differences between both that are handled by that function, driven by the ts->inidle cpu variable and the inidle parameter. The whole guarantees that we only update the dyntick mode on irq exit if we actually interrupted the dyntick idle mode, and that we enter in RCU extended quiescent state from idle loop entry only. Split this function into: - tick_nohz_idle_enter(), which sets ts->inidle to 1, enters dynticks idle mode unconditionally if it can, and enters into RCU extended quiescent state. - tick_nohz_irq_exit() which only updates the dynticks idle mode when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called). To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed into tick_nohz_idle_exit(). This simplifies the code and micro-optimize the irq exit path (no need for local_irq_save there). This also prepares for the split between dynticks and rcu extended quiescent state logics. We'll need this split to further fix illegal uses of RCU in extended quiescent states in the idle loop. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: David Miller <davem@davemloft.net> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Mackerras <paulus@samba.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org>		2011-12-11 10:31:35 -08:00
..
boot	OpenRISC: Build infrastructure	2011-07-22 18:46:30 +02:00
configs	OpenRISC: Build infrastructure	2011-07-22 18:46:30 +02:00
include/asm	doc: fix broken references	2011-09-27 18:08:04 +02:00
kernel	nohz: Separate out irq exit and idle loop dyntick logic	2011-12-11 10:31:35 -08:00
lib	OpenRISC: Library routines	2011-07-22 18:46:40 +02:00
mm	OpenRISC: Build infrastructure	2011-07-22 18:46:30 +02:00
Kconfig	Merge branch 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild	2011-11-06 18:54:53 -08:00
Makefile	OpenRISC: Build infrastructure	2011-07-22 18:46:30 +02:00
README.openrisc	OpenRISC: Miscellaneous	2011-07-22 18:46:41 +02:00
TODO.openrisc	OpenRISC: Miscellaneous	2011-07-22 18:46:41 +02:00

README.openrisc

OpenRISC Linux
==============

This is a port of Linux to the OpenRISC class of microprocessors; the initial
target architecture, specifically, is the 32-bit OpenRISC 1000 family (or1k).

For information about OpenRISC processors and ongoing development:

	website		http://openrisc.net

For more information about Linux on OpenRISC, please contact South Pole AB.

	email:		info@southpole.se

	website:	http://southpole.se
			http://southpoleconsulting.com

---------------------------------------------------------------------

Build instructions for OpenRISC toolchain and Linux
===================================================

In order to build and run Linux for OpenRISC, you'll need at least a basic
toolchain and, perhaps, the architectural simulator.  Steps to get these bits
in place are outlined here.

1)  The toolchain can be obtained from openrisc.net.  Instructions for building
a toolchain can be found at:

http://openrisc.net/toolchain-build.html

2) or1ksim (optional)

or1ksim is the architectural simulator which will allow you to actually run
your OpenRISC Linux kernel if you don't have an OpenRISC processor at hand.

	git clone git://openrisc.net/jonas/or1ksim-svn

	cd or1ksim
	./configure --prefix=$OPENRISC_PREFIX
	make
	make install

3)  Linux kernel

Build the kernel as usual

	make ARCH=openrisc defconfig
	make ARCH=openrisc

4)  Run in architectural simulator

Grab the or1ksim platform configuration file (from the or1ksim source) and
together with your freshly built vmlinux, run your kernel with the following
incantation:

	sim -f arch/openrisc/or1ksim.cfg vmlinux

---------------------------------------------------------------------

Terminology
===========

In the code, the following particles are used on symbols to limit the scope
to more or less specific processor implementations:

openrisc: the OpenRISC class of processors
or1k:     the OpenRISC 1000 family of processors
or1200:   the OpenRISC 1200 processor

---------------------------------------------------------------------

History
========

18. 11. 2003	Matjaz Breskvar (phoenix@bsemi.com)
	initial port of linux to OpenRISC/or32 architecture.
        all the core stuff is implemented and seams usable.

08. 12. 2003	Matjaz Breskvar (phoenix@bsemi.com)
	complete change of TLB miss handling.
	rewrite of exceptions handling.
	fully functional sash-3.6 in default initrd.
	a much improved version with changes all around.

10. 04. 2004	Matjaz Breskvar (phoenix@bsemi.com)
	alot of bugfixes all over.
	ethernet support, functional http and telnet servers.
	running many standard linux apps.

26. 06. 2004	Matjaz Breskvar (phoenix@bsemi.com)
	port to 2.6.x

30. 11. 2004	Matjaz Breskvar (phoenix@bsemi.com)
	lots of bugfixes and enhancments.
	added opencores framebuffer driver.

09. 10. 2010    Jonas Bonn (jonas@southpole.se)
	major rewrite to bring up to par with upstream Linux 2.6.36