kernel-ark/drivers/scsi/arm/Kconfig
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

90 lines
3.1 KiB
Plaintext

#
# SCSI driver configuration for Acorn
#
config SCSI_ACORNSCSI_3
tristate "Acorn SCSI card (aka30) support"
depends on ARCH_ACORN && SCSI
help
This enables support for the Acorn SCSI card (aka30). If you have an
Acorn system with one of these, say Y. If unsure, say N.
config SCSI_ACORNSCSI_TAGGED_QUEUE
bool "Support SCSI 2 Tagged queueing"
depends on SCSI_ACORNSCSI_3
help
Say Y here to enable tagged queuing support on the Acorn SCSI card.
This is a feature of SCSI-2 which improves performance: the host
adapter can send several SCSI commands to a device's queue even if
previous commands haven't finished yet. Some SCSI devices don't
implement this properly, so the safe answer is N.
config SCSI_ACORNSCSI_SYNC
bool "Support SCSI 2 Synchronous Transfers"
depends on SCSI_ACORNSCSI_3
help
Say Y here to enable synchronous transfer negotiation with all
targets on the Acorn SCSI card.
In general, this improves performance; however some SCSI devices
don't implement it properly, so the safe answer is N.
config SCSI_ARXESCSI
tristate "ARXE SCSI support"
depends on ARCH_ACORN && SCSI
help
Around 1991, Arxe Systems Limited released a high density floppy
disc interface for the Acorn Archimedes range, to allow the use of
HD discs from the then new A5000 on earlier models. This interface
was either sold on its own or with an integral SCSI controller.
Technical details on this NCR53c94-based device are available at
<http://www.cryton.demon.co.uk/acornbits/scsi_arxe.html>
Say Y here to compile in support for the SCSI controller.
config SCSI_CUMANA_2
tristate "CumanaSCSI II support"
depends on ARCH_ACORN && SCSI
help
This enables support for the Cumana SCSI II card. If you have an
Acorn system with one of these, say Y. If unsure, say N.
config SCSI_EESOXSCSI
tristate "EESOX support"
depends on ARCH_ACORN && SCSI
help
This enables support for the EESOX SCSI card. If you have an Acorn
system with one of these, say Y, otherwise say N.
config SCSI_POWERTECSCSI
tristate "PowerTec support"
depends on ARCH_ACORN && SCSI
help
This enables support for the Powertec SCSI card on Acorn systems. If
you have one of these, say Y. If unsure, say N.
comment "The following drivers are not fully supported"
depends on ARCH_ACORN && EXPERIMENTAL
config SCSI_CUMANA_1
tristate "CumanaSCSI I support (EXPERIMENTAL)"
depends on ARCH_ACORN && EXPERIMENTAL && SCSI
help
This enables support for the Cumana SCSI I card. If you have an
Acorn system with one of these, say Y. If unsure, say N.
config SCSI_ECOSCSI
tristate "EcoScsi support (EXPERIMENTAL)"
depends on ARCH_ACORN && EXPERIMENTAL && (ARCH_ARC || ARCH_A5K) && SCSI
help
This enables support for the EcoSCSI card -- a small card that sits
in the Econet socket. If you have an Acorn system with one of these,
say Y. If unsure, say N.
config SCSI_OAK1
tristate "Oak SCSI support (EXPERIMENTAL)"
depends on ARCH_ACORN && EXPERIMENTAL && SCSI
help
This enables support for the Oak SCSI card. If you have an Acorn
system with one of these, say Y. If unsure, say N.