e57695e772
Those three new drivers were missed on the initial conversion to ReST format. So: - Rename them to .rst; - Add them to the hwmon index.rst index; - add some blank lines at the "Supported systems:" part, in order to allow Sphinx to properly identify new lines, suppressing warnings and avoid it to output some random lines in bold; - When multiple authors are involved, change the authors part to a list, in order to avoid adding blank lines. - adjust the table cells (one of the tables seemed to be assuming that tab is 4 positions instead of 8) and add the table markup. - be sure that the section markups have the same number of characters as the section title. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
67 lines
1.8 KiB
ReStructuredText
67 lines
1.8 KiB
ReStructuredText
Kernel driver ir38064
|
|
=====================
|
|
|
|
Supported chips:
|
|
|
|
* Infineon IR38064
|
|
|
|
Prefix: 'ir38064'
|
|
Addresses scanned: -
|
|
|
|
Datasheet: Publicly available at the Infineon webiste
|
|
https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca
|
|
|
|
Authors:
|
|
- Maxim Sloyko <maxims@google.com>
|
|
- Patrick Venture <venture@google.com>
|
|
|
|
Description
|
|
-----------
|
|
|
|
IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter.
|
|
|
|
Usage Notes
|
|
-----------
|
|
|
|
This driver does not probe for PMBus devices. You will have to instantiate
|
|
devices explicitly.
|
|
|
|
Sysfs attributes
|
|
----------------
|
|
|
|
======================= ===========================
|
|
curr1_label "iout1"
|
|
curr1_input Measured output current
|
|
curr1_crit Critical maximum current
|
|
curr1_crit_alarm Current critical high alarm
|
|
curr1_max Maximum current
|
|
curr1_max_alarm Current high alarm
|
|
|
|
in1_label "vin"
|
|
in1_input Measured input voltage
|
|
in1_crit Critical maximum input voltage
|
|
in1_crit_alarm Input voltage critical high alarm
|
|
in1_min Minimum input voltage
|
|
in1_min_alarm Input voltage low alarm
|
|
|
|
in2_label "vout1"
|
|
in2_input Measured output voltage
|
|
in2_lcrit Critical minimum output voltage
|
|
in2_lcrit_alarm Output voltage critical low alarm
|
|
in2_crit Critical maximum output voltage
|
|
in2_crit_alarm Output voltage critical high alarm
|
|
in2_max Maximum output voltage
|
|
in2_max_alarm Output voltage high alarm
|
|
in2_min Minimum output voltage
|
|
in2_min_alarm Output voltage low alarm
|
|
|
|
power1_label "pout1"
|
|
power1_input Measured output power
|
|
|
|
temp1_input Measured temperature
|
|
temp1_crit Critical high temperature
|
|
temp1_crit_alarm Chip temperature critical high alarm
|
|
temp1_max Maximum temperature
|
|
temp1_max_alarm Chip temperature high alarm
|
|
======================= ===========================
|