kernel-ark/drivers/rapidio/Kconfig
Alexandre Bounine 2ec3ba69fa rapidio: convert switch drivers to modules
Rework RapidIO switch drivers to add an option to build them as loadable
kernel modules.

This patch removes RapidIO-specific vmlinux section and converts switch
drivers to be compatible with LDM driver registration method.  To simplify
registration of device-specific callback routines this patch introduces
rio_switch_ops data structure.  The sw_sysfs() callback is removed from
the list of device-specific operations because under the new structure its
functions can be handled by switch driver's probe() and remove() routines.

If a specific switch device driver is not loaded the RapidIO subsystem
core will use default standard-based operations to configure a switch.
Because the current implementation of RapidIO enumeration/discovery method
relies on availability of device-specific operations for error management,
switch device drivers must be loaded before the RapidIO
enumeration/discovery starts.

This patch also moves several common routines from enumeration/discovery
module into the RapidIO core code to make switch-specific operations
accessible to all components of RapidIO subsystem.

Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:08:04 -07:00

76 lines
2.2 KiB
Plaintext

#
# RapidIO configuration
#
source "drivers/rapidio/devices/Kconfig"
config RAPIDIO_DISC_TIMEOUT
int "Discovery timeout duration (seconds)"
depends on RAPIDIO
default "30"
---help---
Amount of time a discovery node waits for a host to complete
enumeration before giving up.
config RAPIDIO_ENABLE_RX_TX_PORTS
bool "Enable RapidIO Input/Output Ports"
depends on RAPIDIO
---help---
The RapidIO specification describes a Output port transmit
enable and a Input port receive enable. The recommended state
for Input ports and Output ports should be disabled. When
this switch is set the RapidIO subsystem will enable all
ports for Input/Output direction to allow other traffic
than Maintenance transfers.
config RAPIDIO_DMA_ENGINE
bool "DMA Engine support for RapidIO"
depends on RAPIDIO
select DMADEVICES
select DMA_ENGINE
help
Say Y here if you want to use DMA Engine frameork for RapidIO data
transfers to/from target RIO devices. RapidIO uses NREAD and
NWRITE (NWRITE_R, SWRITE) requests to transfer data between local
memory and memory on remote target device. You need a DMA controller
capable to perform data transfers to/from RapidIO.
If you are unsure about this, say Y here.
config RAPIDIO_DEBUG
bool "RapidIO subsystem debug messages"
depends on RAPIDIO
help
Say Y here if you want the RapidIO subsystem to produce a bunch of
debug messages to the system log. Select this if you are having a
problem with the RapidIO subsystem and want to see more of what is
going on.
If you are unsure about this, say N here.
choice
prompt "Enumeration method"
depends on RAPIDIO
default RAPIDIO_ENUM_BASIC
help
There are different enumeration and discovery mechanisms offered
for RapidIO subsystem. You may select single built-in method or
or any number of methods to be built as modules.
Selecting a built-in method disables use of loadable methods.
If unsure, select Basic built-in.
config RAPIDIO_ENUM_BASIC
tristate "Basic"
help
This option includes basic RapidIO fabric enumeration and discovery
mechanism similar to one described in RapidIO specification Annex 1.
endchoice
menu "RapidIO Switch drivers"
depends on RAPIDIO
source "drivers/rapidio/switches/Kconfig"
endmenu