/* * Definitions for the new Marvell Yukon 2 driver. */ #ifndef _SKY2_H #define _SKY2_H /* PCI config registers */ #define PCI_DEV_REG1 0x40 #define PCI_DEV_REG2 0x44 #define PCI_DEV_STATUS 0x7c #define PCI_OS_PCI_X (1<<26) #define PEX_LNK_STAT 0xf2 #define PEX_UNC_ERR_STAT 0x104 #define PEX_DEV_CTRL 0xe8 /* Yukon-2 */ enum pci_dev_reg_1 { PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */ PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */ PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */ PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */ PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */ PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */ }; enum pci_dev_reg_2 { PCI_VPD_WR_THR = 0xffL<<24, /* Bit 31..24: VPD Write Threshold */ PCI_DEV_SEL = 0x7fL<<17, /* Bit 23..17: EEPROM Device Select */ PCI_VPD_ROM_SZ = 7L<<14, /* Bit 16..14: VPD ROM Size */ PCI_PATCH_DIR = 0xfL<<8, /* Bit 11.. 8: Ext Patches dir 3..0 */ PCI_EXT_PATCHS = 0xfL<<4, /* Bit 7.. 4: Extended Patches 3..0 */ PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */ PCI_REV_DESC = 1<<2, /* Reverse Desc. Bytes */ PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */ }; #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \ PCI_STATUS_SIG_SYSTEM_ERROR | \ PCI_STATUS_REC_MASTER_ABORT | \ PCI_STATUS_REC_TARGET_ABORT | \ PCI_STATUS_PARITY) enum pex_dev_ctrl { PEX_DC_MAX_RRS_MSK = 7<<12, /* Bit 14..12: Max. Read Request Size */ PEX_DC_EN_NO_SNOOP = 1<<11,/* Enable No Snoop */ PEX_DC_EN_AUX_POW = 1<<10,/* Enable AUX Power */ PEX_DC_EN_PHANTOM = 1<<9, /* Enable Phantom Functions */ PEX_DC_EN_EXT_TAG = 1<<8, /* Enable Extended Tag Field */ PEX_DC_MAX_PLS_MSK = 7<<5, /* Bit 7.. 5: Max. Payload Size Mask */ PEX_DC_EN_REL_ORD = 1<<4, /* Enable Relaxed Ordering */ PEX_DC_EN_UNS_RQ_RP = 1<<3, /* Enable Unsupported Request Reporting */ PEX_DC_EN_FAT_ER_RP = 1<<2, /* Enable Fatal Error Reporting */ PEX_DC_EN_NFA_ER_RP = 1<<1, /* Enable Non-Fatal Error Reporting */ PEX_DC_EN_COR_ER_RP = 1<<0, /* Enable Correctable Error Reporting */ }; #define PEX_DC_MAX_RD_RQ_SIZE(x) (((x)<<12) & PEX_DC_MAX_RRS_MSK) /* PEX_UNC_ERR_STAT PEX Uncorrectable Errors Status Register (Yukon-2) */ enum pex_err { PEX_UNSUP_REQ = 1<<20, /* Unsupported Request Error */ PEX_MALFOR_TLP = 1<<18, /* Malformed TLP */ PEX_UNEXP_COMP = 1<<16, /* Unexpected Completion */ PEX_COMP_TO = 1<<14, /* Completion Timeout */ PEX_FLOW_CTRL_P = 1<<13, /* Flow Control Protocol Error */ PEX_POIS_TLP = 1<<12, /* Poisoned TLP */ PEX_DATA_LINK_P = 1<<4, /* Data Link Protocol Error */ PEX_FATAL_ERRORS= (PEX_MALFOR_TLP | PEX_FLOW_CTRL_P | PEX_DATA_LINK_P), }; enum csr_regs { B0_RAP = 0x0000, B0_CTST = 0x0004, B0_Y2LED = 0x0005, B0_POWER_CTRL = 0x0007, B0_ISRC = 0x0008, B0_IMSK = 0x000c, B0_HWE_ISRC = 0x0010, B0_HWE_IMSK = 0x0014, /* Special ISR registers (Yukon-2 only) */ B0_Y2_SP_ISRC2 = 0x001c, B0_Y2_SP_ISRC3 = 0x0020, B0_Y2_SP_EISR = 0x0024, B0_Y2_SP_LISR = 0x0028, B0_Y2_SP_ICR = 0x002c, B2_MAC_1 = 0x0100, B2_MAC_2 = 0x0108, B2_MAC_3 = 0x0110, B2_CONN_TYP = 0x0118, B2_PMD_TYP = 0x0119, B2_MAC_CFG = 0x011a, B2_CHIP_ID = 0x011b, B2_E_0 = 0x011c, B2_Y2_CLK_GATE = 0x011d, B2_Y2_HW_RES = 0x011e, B2_E_3 = 0x011f, B2_Y2_CLK_CTRL = 0x0120, B2_TI_INI = 0x0130, B2_TI_VAL = 0x0134, B2_TI_CTRL = 0x0138, B2_TI_TEST = 0x0139, B2_TST_CTRL1 = 0x0158, B2_TST_CTRL2 = 0x0159, B2_GP_IO = 0x015c, B2_I2C_CTRL = 0x0160, B2_I2C_DATA = 0x0164, B2_I2C_IRQ = 0x0168, B2_I2C_SW = 0x016c, B3_RAM_ADDR = 0x0180, B3_RAM_DATA_LO = 0x0184, B3_RAM_DATA_HI = 0x0188, /* RAM Interface Registers */ /* Yukon-2: use RAM_BUFFER() to access the RAM buffer */ /* * The HW-Spec. calls this registers Timeout Value 0..11. But this names are * not usable in SW. Please notice these are NOT real timeouts, these are * the number of qWords transferred continuously. */ #define RAM_BUFFER(port, reg) (reg | (port <<6)) B3_RI_WTO_R1 = 0x0190, B3_RI_WTO_XA1 = 0x0191, B3_RI_WTO_XS1 = 0x0192, B3_RI_RTO_R1 = 0x0193, B3_RI_RTO_XA1 = 0x0194, B3_RI_RTO_XS1 = 0x0195, B3_RI_WTO_R2 = 0x0196, B3_RI_WTO_XA2 = 0x0197, B3_RI_WTO_XS2 = 0x0198, B3_RI_RTO_R2 = 0x0199, B3_RI_RTO_XA2 = 0x019a, B3_RI_RTO_XS2 = 0x019b, B3_RI_TO_VAL = 0x019c, B3_RI_CTRL = 0x01a0, B3_RI_TEST = 0x01a2, B3_MA_TOINI_RX1 = 0x01b0, B3_MA_TOINI_RX2 = 0x01b1, B3_MA_TOINI_TX1 = 0x01b2, B3_MA_TOINI_TX2 = 0x01b3, B3_MA_TOVAL_RX1 = 0x01b4, B3_MA_TOVAL_RX2 = 0x01b5, B3_MA_TOVAL_TX1 = 0x01b6, B3_MA_TOVAL_TX2 = 0x01b7, B3_MA_TO_CTRL = 0x01b8, B3_MA_TO_TEST = 0x01ba, B3_MA_RCINI_RX1 = 0x01c0, B3_MA_RCINI_RX2 = 0x01c1, B3_MA_RCINI_TX1 = 0x01c2, B3_MA_RCINI_TX2 = 0x01c3, B3_MA_RCVAL_RX1 = 0x01c4, B3_MA_RCVAL_RX2 = 0x01c5, B3_MA_RCVAL_TX1 = 0x01c6, B3_MA_RCVAL_TX2 = 0x01c7, B3_MA_RC_CTRL = 0x01c8, B3_MA_RC_TEST = 0x01ca, B3_PA_TOINI_RX1 = 0x01d0, B3_PA_TOINI_RX2 = 0x01d4, B3_PA_TOINI_TX1 = 0x01d8, B3_PA_TOINI_TX2 = 0x01dc, B3_PA_TOVAL_RX1 = 0x01e0, B3_PA_TOVAL_RX2 = 0x01e4, B3_PA_TOVAL_TX1 = 0x01e8, B3_PA_TOVAL_TX2 = 0x01ec, B3_PA_CTRL = 0x01f0, B3_PA_TEST = 0x01f2, Y2_CFG_SPC = 0x1c00, }; /* B0_CTST 16 bit Control/Status register */ enum { Y2_VMAIN_AVAIL = 1<<17,/* VMAIN available (YUKON-2 only) */ Y2_VAUX_AVAIL = 1<<16,/* VAUX available (YUKON-2 only) */ Y2_ASF_ENABLE = 1<<13,/* ASF Unit Enable (YUKON-2 only) */ Y2_ASF_DISABLE = 1<<12,/* ASF Unit Disable (YUKON-2 only) */ Y2_CLK_RUN_ENA = 1<<11,/* CLK_RUN Enable (YUKON-2 only) */ Y2_CLK_RUN_DIS = 1<<10,/* CLK_RUN Disable (YUKON-2 only) */ Y2_LED_STAT_ON = 1<<9, /* Status LED On (YUKON-2 only) */ Y2_LED_STAT_OFF = 1<<8, /* Status LED Off (YUKON-2 only) */ CS_ST_SW_IRQ = 1<<7, /* Set IRQ SW Request */ CS_CL_SW_IRQ = 1<<6, /* Clear IRQ SW Request */ CS_STOP_DONE = 1<<5, /* Stop Master is finished */ CS_STOP_MAST = 1<<4, /* Command Bit to stop the master */ CS_MRST_CLR = 1<<3, /* Clear Master reset */ CS_MRST_SET = 1<<2, /* Set Master reset */ CS_RST_CLR = 1<<1, /* Clear Software reset */ CS_RST_SET = 1, /* Set Software reset */ }; /* B0_LED 8 Bit LED register */ enum { /* Bit 7.. 2: reserved */ LED_STAT_ON = 1<<1, /* Status LED on */ LED_STAT_OFF = 1, /* Status LED off */ }; /* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */ enum { PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */ PC_VAUX_DIS = 1<<6, /* Switch VAUX Disable */ PC_VCC_ENA = 1<<5, /* Switch VCC Enable */ PC_VCC_DIS = 1<<4, /* Switch VCC Disable */ PC_VAUX_ON = 1<<3, /* Switch VAUX On */ PC_VAUX_OFF = 1<<2, /* Switch VAUX Off */ PC_VCC_ON = 1<<1, /* Switch VCC On */ PC_VCC_OFF = 1<<0, /* Switch VCC Off */ }; /* B2_IRQM_MSK 32 bit IRQ Moderation Mask */ /* B0_Y2_SP_ISRC2 32 bit Special Interrupt Source Reg 2 */ /* B0_Y2_SP_ISRC3 32 bit Special Interrupt Source Reg 3 */ /* B0_Y2_SP_EISR 32 bit Enter ISR Reg */ /* B0_Y2_SP_LISR 32 bit Leave ISR Reg */ enum { Y2_IS_HW_ERR = 1<<31, /* Interrupt HW Error */ Y2_IS_STAT_BMU = 1<<30, /* Status BMU Interrupt */ Y2_IS_ASF = 1<<29, /* ASF subsystem Interrupt */ Y2_IS_POLL_CHK = 1<<27, /* Check IRQ from polling unit */ Y2_IS_TWSI_RDY = 1<<26, /* IRQ on end of TWSI Tx */ Y2_IS_IRQ_SW = 1<<25, /* SW forced IRQ */ Y2_IS_TIMINT = 1<<24, /* IRQ from Timer */ Y2_IS_IRQ_PHY2 = 1<<12, /* Interrupt from PHY 2 */ Y2_IS_IRQ_MAC2 = 1<<11, /* Interrupt from MAC 2 */ Y2_IS_CHK_RX2 = 1<<10, /* Descriptor error Rx 2 */ Y2_IS_CHK_TXS2 = 1<<9, /* Descriptor error TXS 2 */ Y2_IS_CHK_TXA2 = 1<<8, /* Descriptor error TXA 2 */ Y2_IS_IRQ_PHY1 = 1<<4, /* Interrupt from PHY 1 */ Y2_IS_IRQ_MAC1 = 1<<3, /* Interrupt from MAC 1 */ Y2_IS_CHK_RX1 = 1<<2, /* Descriptor error Rx 1 */ Y2_IS_CHK_TXS1 = 1<<1, /* Descriptor error TXS 1 */ Y2_IS_CHK_TXA1 = 1<<0, /* Descriptor error TXA 1 */ Y2_IS_BASE = Y2_IS_HW_ERR | Y2_IS_STAT_BMU | Y2_IS_POLL_CHK | Y2_IS_TWSI_RDY | Y2_IS_IRQ_SW | Y2_IS_TIMINT, Y2_IS_PORT_1 = Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1 | Y2_IS_CHK_RX1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_TXS1, Y2_IS_PORT_2 = Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2 | Y2_IS_CHK_RX2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_TXS2, }; /* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */ enum { IS_ERR_MSK = 0x00003fff,/* All Error bits */ IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */ IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */ IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */ IS_IRQ_STAT = 1<<10, /* IRQ status exception */ IS_NO_STAT_M1 = 1<<9, /* No Rx Status from MAC 1 */ IS_NO_STAT_M2 = 1<<8, /* No Rx Status from MAC 2 */ IS_NO_TIST_M1 = 1<<7, /* No Time Stamp from MAC 1 */ IS_NO_TIST_M2 = 1<<6, /* No Time Stamp from MAC 2 */ IS_RAM_RD_PAR = 1<<5, /* RAM Read Parity Error */ IS_RAM_WR_PAR = 1<<4, /* RAM Write Parity Error */ IS_M1_PAR_ERR = 1<<3, /* MAC 1 Parity Error */ IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */ IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */ IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */ }; /* Hardware error interrupt mask for Yukon 2 */ enum { Y2_IS_TIST_OV = 1<<29,/* Time Stamp Timer overflow interrupt */ Y2_IS_SENSOR = 1<<28, /* Sensor interrupt */ Y2_IS_MST_ERR = 1<<27, /* Master error interrupt */ Y2_IS_IRQ_STAT = 1<<26, /* Status exception interrupt */ Y2_IS_PCI_EXP = 1<<25, /* PCI-Express interrupt */ Y2_IS_PCI_NEXP = 1<<24, /* PCI-Express error similar to PCI error */ /* Link 2 */ Y2_IS_PAR_RD2 = 1<<13, /* Read RAM parity error interrupt */ Y2_IS_PAR_WR2 = 1<<12, /* Write RAM parity error interrupt */ Y2_IS_PAR_MAC2 = 1<<11, /* MAC hardware fault interrupt */ Y2_IS_PAR_RX2 = 1<<10, /* Parity Error Rx Queue 2 */ Y2_IS_TCP_TXS2 = 1<<9, /* TCP length mismatch sync Tx queue IRQ */ Y2_IS_TCP_TXA2 = 1<<8, /* TCP length mismatch async Tx queue IRQ */ /* Link 1 */ Y2_IS_PAR_RD1 = 1<<5, /* Read RAM parity error interrupt */ Y2_IS_PAR_WR1 = 1<<4, /* Write RAM parity error interrupt */ Y2_IS_PAR_MAC1 = 1<<3, /* MAC hardware fault interrupt */ Y2_IS_PAR_RX1 = 1<<2, /* Parity Error Rx Queue 1 */ Y2_IS_TCP_TXS1 = 1<<1, /* TCP length mismatch sync Tx queue IRQ */ Y2_IS_TCP_TXA1 = 1<<0, /* TCP length mismatch async Tx queue IRQ */ Y2_HWE_L1_MASK = Y2_IS_PAR_RD1 | Y2_IS_PAR_WR1 | Y2_IS_PAR_MAC1 | Y2_IS_PAR_RX1 | Y2_IS_TCP_TXS1| Y2_IS_TCP_TXA1, Y2_HWE_L2_MASK = Y2_IS_PAR_RD2 | Y2_IS_PAR_WR2 | Y2_IS_PAR_MAC2 | Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2, Y2_HWE_ALL_MASK = Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT | Y2_IS_PCI_EXP | Y2_IS_PCI_NEXP | Y2_HWE_L1_MASK | Y2_HWE_L2_MASK, }; /* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */ enum { DPT_START = 1<<1, DPT_STOP = 1<<0, }; /* B2_TST_CTRL1 8 bit Test Control Register 1 */ enum { TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */ TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */ TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */ TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */ TST_FRC_APERR_M = 1<<3, /* force ADDRPERR on MST */ TST_FRC_APERR_T = 1<<2, /* force ADDRPERR on TRG */ TST_CFG_WRITE_ON = 1<<1, /* Enable Config Reg WR */ TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */ }; /* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */ enum { CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */ /* Bit 3.. 2: reserved */ CFG_DIS_M2_CLK = 1<<1, /* Disable Clock for 2nd MAC */ CFG_SNG_MAC = 1<<0, /* MAC Config: 0=2 MACs / 1=1 MAC*/ }; /* B2_CHIP_ID 8 bit Chip Identification Number */ enum { CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */ CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */ CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */ CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */ CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */ CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */ CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */ CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */ CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */ CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */ }; /* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */ enum { Y2_STATUS_LNK2_INAC = 1<<7, /* Status Link 2 inactiv (0 = activ) */ Y2_CLK_GAT_LNK2_DIS = 1<<6, /* Disable clock gating Link 2 */ Y2_COR_CLK_LNK2_DIS = 1<<5, /* Disable Core clock Link 2 */ Y2_PCI_CLK_LNK2_DIS = 1<<4, /* Disable PCI clock Link 2 */ Y2_STATUS_LNK1_INAC = 1<<3, /* Status Link 1 inactiv (0 = activ) */ Y2_CLK_GAT_LNK1_DIS = 1<<2, /* Disable clock gating Link 1 */ Y2_COR_CLK_LNK1_DIS = 1<<1, /* Disable Core clock Link 1 */ Y2_PCI_CLK_LNK1_DIS = 1<<0, /* Disable PCI clock Link 1 */ }; /* B2_Y2_HW_RES 8 bit HW Resources (Yukon-2 only) */ enum { CFG_LED_MODE_MSK = 7<<2, /* Bit 4.. 2: LED Mode Mask */ CFG_LINK_2_AVAIL = 1<<1, /* Link 2 available */ CFG_LINK_1_AVAIL = 1<<0, /* Link 1 available */ }; #define CFG_LED_MODE(x) (((x) & CFG_LED_MODE_MSK) >> 2) #define CFG_DUAL_MAC_MSK (CFG_LINK_2_AVAIL | CFG_LINK_1_AVAIL) /* B2_Y2_CLK_CTRL 32 bit Clock Frequency Control Register (Yukon-2/EC) */ enum { Y2_CLK_DIV_VAL_MSK = 0xff<<16,/* Bit 23..16: Clock Divisor Value */ #define Y2_CLK_DIV_VAL(x) (((x)<<16) & Y2_CLK_DIV_VAL_MSK) Y2_CLK_DIV_VAL2_MSK = 7<<21, /* Bit 23..21: Clock Divisor Value */ Y2_CLK_SELECT2_MSK = 0x1f<<16,/* Bit 20..16: Clock Select */ #define Y2_CLK_DIV_VAL_2(x) (((x)<<21) & Y2_CLK_DIV_VAL2_MSK) #define Y2_CLK_SEL_VAL_2(x) (((x)<<16) & Y2_CLK_SELECT2_MSK) Y2_CLK_DIV_ENA = 1<<1, /* Enable Core Clock Division */ Y2_CLK_DIV_DIS = 1<<0, /* Disable Core Clock Division */ }; /* B2_TI_CTRL 8 bit Timer control */ /* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */ enum { TIM_START = 1<<2, /* Start Timer */ TIM_STOP = 1<<1, /* Stop Timer */ TIM_CLR_IRQ = 1<<0, /* Clear Timer IRQ (!IRQM) */ }; /* B2_TI_TEST 8 Bit Timer Test */ /* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */ /* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */ enum { TIM_T_ON = 1<<2, /* Test mode on */ TIM_T_OFF = 1<<1, /* Test mode off */ TIM_T_STEP = 1<<0, /* Test step */ }; /* B3_RAM_ADDR 32 bit RAM Address, to read or write */ /* Bit 31..19: reserved */ #define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */ /* RAM Interface Registers */ /* B3_RI_CTRL 16 bit RAM Iface Control Register */ enum { RI_CLR_RD_PERR = 1<<9, /* Clear IRQ RAM Read Parity Err */ RI_CLR_WR_PERR = 1<<8, /* Clear IRQ RAM Write Parity Err*/ RI_RST_CLR = 1<<1, /* Clear RAM Interface Reset */ RI_RST_SET = 1<<0, /* Set RAM Interface Reset */ }; #define SK_RI_TO_53 36 /* RAM interface timeout */ /* Port related registers FIFO, and Arbiter */ #define SK_REG(port,reg) (((port)<<7)+(reg)) /* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */ /* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */ /* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */ /* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */ /* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */ #define TXA_MAX_VAL 0x00ffffffUL /* Bit 23.. 0: Max TXA Timer/Cnt Val */ /* TXA_CTRL 8 bit Tx Arbiter Control Register */ enum { TXA_ENA_FSYNC = 1<<7, /* Enable force of sync Tx queue */ TXA_DIS_FSYNC = 1<<6, /* Disable force of sync Tx queue */ TXA_ENA_ALLOC = 1<<5, /* Enable alloc of free bandwidth */ TXA_DIS_ALLOC = 1<<4, /* Disable alloc of free bandwidth */ TXA_START_RC = 1<<3, /* Start sync Rate Control */ TXA_STOP_RC = 1<<2, /* Stop sync Rate Control */ TXA_ENA_ARB = 1<<1, /* Enable Tx Arbiter */ TXA_DIS_ARB = 1<<0, /* Disable Tx Arbiter */ }; /* * Bank 4 - 5 */ /* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */ enum { TXA_ITI_INI = 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/ TXA_ITI_VAL = 0x0204,/* 32 bit Tx Arb Interval Timer Value */ TXA_LIM_INI = 0x0208,/* 32 bit Tx Arb Limit Counter Init Val */ TXA_LIM_VAL = 0x020c,/* 32 bit Tx Arb Limit Counter Value */ TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */ TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */ TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */ }; enum { B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */ B7_CFG_SPC = 0x0380,/* copy of the Configuration register */ B8_RQ1_REGS = 0x0400,/* Receive Queue 1 */ B8_RQ2_REGS = 0x0480,/* Receive Queue 2 */ B8_TS1_REGS = 0x0600,/* Transmit sync queue 1 */ B8_TA1_REGS = 0x0680,/* Transmit async queue 1 */ B8_TS2_REGS = 0x0700,/* Transmit sync queue 2 */ B8_TA2_REGS = 0x0780,/* Transmit sync queue 2 */ B16_RAM_REGS = 0x0800,/* RAM Buffer Registers */ }; /* Queue Register Offsets, use Q_ADDR() to access */ enum { B8_Q_REGS = 0x0400, /* base of Queue registers */ Q_D = 0x00, /* 8*32 bit Current Descriptor */ Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */ Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */ Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */ Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */ Q_BC = 0x30, /* 32 bit Current Byte Counter */ Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */ Q_F = 0x38, /* 32 bit Flag Register */ Q_T1 = 0x3c, /* 32 bit Test Register 1 */ Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */ Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */ Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */ Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */ Q_T2 = 0x40, /* 32 bit Test Register 2 */ Q_T3 = 0x44, /* 32 bit Test Register 3 */ /* Yukon-2 */ Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */ Q_WM = 0x40, /* 16 bit FIFO Watermark */ Q_AL = 0x42, /* 8 bit FIFO Alignment */ Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */ Q_RSL = 0x46, /* 8 bit FIFO Read Shadow Level */ Q_RP = 0x48, /* 8 bit FIFO Read Pointer */ Q_RL = 0x4a, /* 8 bit FIFO Read Level */ Q_WP = 0x4c, /* 8 bit FIFO Write Pointer */ Q_WSP = 0x4d, /* 8 bit FIFO Write Shadow Pointer */ Q_WL = 0x4e, /* 8 bit FIFO Write Level */ Q_WSL = 0x4f, /* 8 bit FIFO Write Shadow Level */ }; #define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs)) /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/ enum { Y2_B8_PREF_REGS = 0x0450, PREF_UNIT_CTRL = 0x00, /* 32 bit Control register */ PREF_UNIT_LAST_IDX = 0x04, /* 16 bit Last Index */ PREF_UNIT_ADDR_LO = 0x08, /* 32 bit List start addr, low part */ PREF_UNIT_ADDR_HI = 0x0c, /* 32 bit List start addr, high part*/ PREF_UNIT_GET_IDX = 0x10, /* 16 bit Get Index */ PREF_UNIT_PUT_IDX = 0x14, /* 16 bit Put Index */ PREF_UNIT_FIFO_WP = 0x20, /* 8 bit FIFO write pointer */ PREF_UNIT_FIFO_RP = 0x24, /* 8 bit FIFO read pointer */ PREF_UNIT_FIFO_WM = 0x28, /* 8 bit FIFO watermark */ PREF_UNIT_FIFO_LEV = 0x2c, /* 8 bit FIFO level */ PREF_UNIT_MASK_IDX = 0x0fff, }; #define Y2_QADDR(q,reg) (Y2_B8_PREF_REGS + (q) + (reg)) /* RAM Buffer Register Offsets */ enum { RB_START = 0x00,/* 32 bit RAM Buffer Start Address */ RB_END = 0x04,/* 32 bit RAM Buffer End Address */ RB_WP = 0x08,/* 32 bit RAM Buffer Write Pointer */ RB_RP = 0x0c,/* 32 bit RAM Buffer Read Pointer */ RB_RX_UTPP = 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */ RB_RX_LTPP = 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */ RB_RX_UTHP = 0x18,/* 32 bit Rx Upper Threshold, High Prio */ RB_RX_LTHP = 0x1c,/* 32 bit Rx Lower Threshold, High Prio */ /* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */ RB_PC = 0x20,/* 32 bit RAM Buffer Packet Counter */ RB_LEV = 0x24,/* 32 bit RAM Buffer Level Register */ RB_CTRL = 0x28,/* 32 bit RAM Buffer Control Register */ RB_TST1 = 0x29,/* 8 bit RAM Buffer Test Register 1 */ RB_TST2 = 0x2a,/* 8 bit RAM Buffer Test Register 2 */ }; /* Receive and Transmit Queues */ enum { Q_R1 = 0x0000, /* Receive Queue 1 */ Q_R2 = 0x0080, /* Receive Queue 2 */ Q_XS1 = 0x0200, /* Synchronous Transmit Queue 1 */ Q_XA1 = 0x0280, /* Asynchronous Transmit Queue 1 */ Q_XS2 = 0x0300, /* Synchronous Transmit Queue 2 */ Q_XA2 = 0x0380, /* Asynchronous Transmit Queue 2 */ }; /* Different PHY Types */ enum { PHY_ADDR_MARV = 0, }; #define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs)) enum { LNK_SYNC_INI = 0x0c30,/* 32 bit Link Sync Cnt Init Value */ LNK_SYNC_VAL = 0x0c34,/* 32 bit Link Sync Cnt Current Value */ LNK_SYNC_CTRL = 0x0c38,/* 8 bit Link Sync Cnt Control Register */ LNK_SYNC_TST = 0x0c39,/* 8 bit Link Sync Cnt Test Register */ LNK_LED_REG = 0x0c3c,/* 8 bit Link LED Register */ /* Receive GMAC FIFO (YUKON and Yukon-2) */ RX_GMF_EA = 0x0c40,/* 32 bit Rx GMAC FIFO End Address */ RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */ RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */ RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */ RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */ RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */ RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */ RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */ RX_GMF_WLEV = 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */ RX_GMF_RP = 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */ RX_GMF_RLEV = 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */ }; /* Q_BC 32 bit Current Byte Counter */ /* BMU Control Status Registers */ /* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */ /* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */ /* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */ /* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */ /* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */ /* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */ /* Q_CSR 32 bit BMU Control/Status Register */ /* Rx BMU Control / Status Registers (Yukon-2) */ enum { BMU_IDLE = 1<<31, /* BMU Idle State */ BMU_RX_TCP_PKT = 1<<30, /* Rx TCP Packet (when RSS Hash enabled) */ BMU_RX_IP_PKT = 1<<29, /* Rx IP Packet (when RSS Hash enabled) */ BMU_ENA_RX_RSS_HASH = 1<<15, /* Enable Rx RSS Hash */ BMU_DIS_RX_RSS_HASH = 1<<14, /* Disable Rx RSS Hash */ BMU_ENA_RX_CHKSUM = 1<<13, /* Enable Rx TCP/IP Checksum Check */ BMU_DIS_RX_CHKSUM = 1<<12, /* Disable Rx TCP/IP Checksum Check */ BMU_CLR_IRQ_PAR = 1<<11, /* Clear IRQ on Parity errors (Rx) */ BMU_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segmen. error (Tx) */ BMU_CLR_IRQ_CHK = 1<<10, /* Clear IRQ Check */ BMU_STOP = 1<<9, /* Stop Rx/Tx Queue */ BMU_START = 1<<8, /* Start Rx/Tx Queue */ BMU_FIFO_OP_ON = 1<<7, /* FIFO Operational On */ BMU_FIFO_OP_OFF = 1<<6, /* FIFO Operational Off */ BMU_FIFO_ENA = 1<<5, /* Enable FIFO */ BMU_FIFO_RST = 1<<4, /* Reset FIFO */ BMU_OP_ON = 1<<3, /* BMU Operational On */ BMU_OP_OFF = 1<<2, /* BMU Operational Off */ BMU_RST_CLR = 1<<1, /* Clear BMU Reset (Enable) */ BMU_RST_SET = 1<<0, /* Set BMU Reset */ BMU_CLR_RESET = BMU_FIFO_RST | BMU_OP_OFF | BMU_RST_CLR, BMU_OPER_INIT = BMU_CLR_IRQ_PAR | BMU_CLR_IRQ_CHK | BMU_START | BMU_FIFO_ENA | BMU_OP_ON, }; /* Tx BMU Control / Status Registers (Yukon-2) */ /* Bit 31: same as for Rx */ enum { BMU_TX_IPIDINCR_ON = 1<<13, /* Enable IP ID Increment */ BMU_TX_IPIDINCR_OFF = 1<<12, /* Disable IP ID Increment */ BMU_TX_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segm. length mism. */ }; /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/ /* PREF_UNIT_CTRL 32 bit Prefetch Control register */ enum { PREF_UNIT_OP_ON = 1<<3, /* prefetch unit operational */ PREF_UNIT_OP_OFF = 1<<2, /* prefetch unit not operational */ PREF_UNIT_RST_CLR = 1<<1, /* Clear Prefetch Unit Reset */ PREF_UNIT_RST_SET = 1<<0, /* Set Prefetch Unit Reset */ }; /* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */ /* RB_START 32 bit RAM Buffer Start Address */ /* RB_END 32 bit RAM Buffer End Address */ /* RB_WP 32 bit RAM Buffer Write Pointer */ /* RB_RP 32 bit RAM Buffer Read Pointer */ /* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */ /* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */ /* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */ /* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */ /* RB_PC 32 bit RAM Buffer Packet Counter */ /* RB_LEV 32 bit RAM Buffer Level Register */ #define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */ /* RB_TST2 8 bit RAM Buffer Test Register 2 */ /* RB_TST1 8 bit RAM Buffer Test Register 1 */ /* RB_CTRL 8 bit RAM Buffer Control Register */ enum { RB_ENA_STFWD = 1<<5, /* Enable Store & Forward */ RB_DIS_STFWD = 1<<4, /* Disable Store & Forward */ RB_ENA_OP_MD = 1<<3, /* Enable Operation Mode */ RB_DIS_OP_MD = 1<<2, /* Disable Operation Mode */ RB_RST_CLR = 1<<1, /* Clear RAM Buf STM Reset */ RB_RST_SET = 1<<0, /* Set RAM Buf STM Reset */ }; /* Transmit GMAC FIFO (YUKON only) */ enum { TX_GMF_EA = 0x0d40,/* 32 bit Tx GMAC FIFO End Address */ TX_GMF_AE_THR = 0x0d44,/* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/ TX_GMF_CTRL_T = 0x0d48,/* 32 bit Tx GMAC FIFO Control/Test */ TX_GMF_WP = 0x0d60,/* 32 bit Tx GMAC FIFO Write Pointer */ TX_GMF_WSP = 0x0d64,/* 32 bit Tx GMAC FIFO Write Shadow Ptr. */ TX_GMF_WLEV = 0x0d68,/* 32 bit Tx GMAC FIFO Write Level */ TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */ TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */ TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */ }; /* Descriptor Poll Timer Registers */ enum { B28_DPT_INI = 0x0e00,/* 24 bit Descriptor Poll Timer Init Val */ B28_DPT_VAL = 0x0e04,/* 24 bit Descriptor Poll Timer Curr Val */ B28_DPT_CTRL = 0x0e08,/* 8 bit Descriptor Poll Timer Ctrl Reg */ B28_DPT_TST = 0x0e0a,/* 8 bit Descriptor Poll Timer Test Reg */ }; /* Time Stamp Timer Registers (YUKON only) */ enum { GMAC_TI_ST_VAL = 0x0e14,/* 32 bit Time Stamp Timer Curr Val */ GMAC_TI_ST_CTRL = 0x0e18,/* 8 bit Time Stamp Timer Ctrl Reg */ GMAC_TI_ST_TST = 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */ }; /* Polling Unit Registers (Yukon-2 only) */ enum { POLL_CTRL = 0x0e20, /* 32 bit Polling Unit Control Reg */ POLL_LAST_IDX = 0x0e24,/* 16 bit Polling Unit List Last Index */ POLL_LIST_ADDR_LO= 0x0e28,/* 32 bit Poll. List Start Addr (low) */ POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit Poll. List Start Addr (high) */ }; /* ASF Subsystem Registers (Yukon-2 only) */ enum { B28_Y2_SMB_CONFIG = 0x0e40,/* 32 bit ASF SMBus Config Register */ B28_Y2_SMB_CSD_REG = 0x0e44,/* 32 bit ASF SMB Control/Status/Data */ B28_Y2_ASF_IRQ_V_BASE=0x0e60,/* 32 bit ASF IRQ Vector Base */ B28_Y2_ASF_STAT_CMD= 0x0e68,/* 32 bit ASF Status and Command Reg */ B28_Y2_ASF_HOST_COM= 0x0e6c,/* 32 bit ASF Host Communication Reg */ B28_Y2_DATA_REG_1 = 0x0e70,/* 32 bit ASF/Host Data Register 1 */ B28_Y2_DATA_REG_2 = 0x0e74,/* 32 bit ASF/Host Data Register 2 */ B28_Y2_DATA_REG_3 = 0x0e78,/* 32 bit ASF/Host Data Register 3 */ B28_Y2_DATA_REG_4 = 0x0e7c,/* 32 bit ASF/Host Data Register 4 */ }; /* Status BMU Registers (Yukon-2 only)*/ enum { STAT_CTRL = 0x0e80,/* 32 bit Status BMU Control Reg */ STAT_LAST_IDX = 0x0e84,/* 16 bit Status BMU Last Index */ STAT_LIST_ADDR_LO= 0x0e88,/* 32 bit Status List Start Addr (low) */ STAT_LIST_ADDR_HI= 0x0e8c,/* 32 bit Status List Start Addr (high) */ STAT_TXA1_RIDX = 0x0e90,/* 16 bit Status TxA1 Report Index Reg */ STAT_TXS1_RIDX = 0x0e92,/* 16 bit Status TxS1 Report Index Reg */ STAT_TXA2_RIDX = 0x0e94,/* 16 bit Status TxA2 Report Index Reg */ STAT_TXS2_RIDX = 0x0e96,/* 16 bit Status TxS2 Report Index Reg */ STAT_TX_IDX_TH = 0x0e98,/* 16 bit Status Tx Index Threshold Reg */ STAT_PUT_IDX = 0x0e9c,/* 16 bit Status Put Index Reg */ /* FIFO Control/Status Registers (Yukon-2 only)*/ STAT_FIFO_WP = 0x0ea0,/* 8 bit Status FIFO Write Pointer Reg */ STAT_FIFO_RP = 0x0ea4,/* 8 bit Status FIFO Read Pointer Reg */ STAT_FIFO_RSP = 0x0ea6,/* 8 bit Status FIFO Read Shadow Ptr */ STAT_FIFO_LEVEL = 0x0ea8,/* 8 bit Status FIFO Level Reg */ STAT_FIFO_SHLVL = 0x0eaa,/* 8 bit Status FIFO Shadow Level Reg */ STAT_FIFO_WM = 0x0eac,/* 8 bit Status FIFO Watermark Reg */ STAT_FIFO_ISR_WM= 0x0ead,/* 8 bit Status FIFO ISR Watermark Reg */ /* Level and ISR Timer Registers (Yukon-2 only)*/ STAT_LEV_TIMER_INI= 0x0eb0,/* 32 bit Level Timer Init. Value Reg */ STAT_LEV_TIMER_CNT= 0x0eb4,/* 32 bit Level Timer Counter Reg */ STAT_LEV_TIMER_CTRL= 0x0eb8,/* 8 bit Level Timer Control Reg */ STAT_LEV_TIMER_TEST= 0x0eb9,/* 8 bit Level Timer Test Reg */ STAT_TX_TIMER_INI = 0x0ec0,/* 32 bit Tx Timer Init. Value Reg */ STAT_TX_TIMER_CNT = 0x0ec4,/* 32 bit Tx Timer Counter Reg */ STAT_TX_TIMER_CTRL = 0x0ec8,/* 8 bit Tx Timer Control Reg */ STAT_TX_TIMER_TEST = 0x0ec9,/* 8 bit Tx Timer Test Reg */ STAT_ISR_TIMER_INI = 0x0ed0,/* 32 bit ISR Timer Init. Value Reg */ STAT_ISR_TIMER_CNT = 0x0ed4,/* 32 bit ISR Timer Counter Reg */ STAT_ISR_TIMER_CTRL= 0x0ed8,/* 8 bit ISR Timer Control Reg */ STAT_ISR_TIMER_TEST= 0x0ed9,/* 8 bit ISR Timer Test Reg */ }; enum { LINKLED_OFF = 0x01, LINKLED_ON = 0x02, LINKLED_LINKSYNC_OFF = 0x04, LINKLED_LINKSYNC_ON = 0x08, LINKLED_BLINK_OFF = 0x10, LINKLED_BLINK_ON = 0x20, }; /* GMAC and GPHY Control Registers (YUKON only) */ enum { GMAC_CTRL = 0x0f00,/* 32 bit GMAC Control Reg */ GPHY_CTRL = 0x0f04,/* 32 bit GPHY Control Reg */ GMAC_IRQ_SRC = 0x0f08,/* 8 bit GMAC Interrupt Source Reg */ GMAC_IRQ_MSK = 0x0f0c,/* 8 bit GMAC Interrupt Mask Reg */ GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */ /* Wake-up Frame Pattern Match Control Registers (YUKON only) */ WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */ WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */ WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */ WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */ WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */ WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */ WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */ WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */ /* WOL Pattern Length Registers (YUKON only) */ WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */ WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */ /* WOL Pattern Counter Registers (YUKON only) */ WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */ WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */ }; enum { WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */ WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */ }; enum { BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */ BASE_GMAC_2 = 0x3800,/* GMAC 2 registers */ }; /* * Marvel-PHY Registers, indirect addressed over GMAC */ enum { PHY_MARV_CTRL = 0x00,/* 16 bit r/w PHY Control Register */ PHY_MARV_STAT = 0x01,/* 16 bit r/o PHY Status Register */ PHY_MARV_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */ PHY_MARV_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */ PHY_MARV_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */ PHY_MARV_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */ PHY_MARV_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */ PHY_MARV_NEPG = 0x07,/* 16 bit r/w Next Page Register */ PHY_MARV_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */ /* Marvel-specific registers */ PHY_MARV_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */ PHY_MARV_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */ PHY_MARV_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */ PHY_MARV_PHY_CTRL = 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */ PHY_MARV_PHY_STAT = 0x11,/* 16 bit r/o PHY Specific Stat Reg */ PHY_MARV_INT_MASK = 0x12,/* 16 bit r/w Interrupt Mask Reg */ PHY_MARV_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */ PHY_MARV_EXT_CTRL = 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */ PHY_MARV_RXE_CNT = 0x15,/* 16 bit r/w Receive Error Counter */ PHY_MARV_EXT_ADR = 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */ PHY_MARV_PORT_IRQ = 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */ PHY_MARV_LED_CTRL = 0x18,/* 16 bit r/w LED Control Reg */ PHY_MARV_LED_OVER = 0x19,/* 16 bit r/w Manual LED Override Reg */ PHY_MARV_EXT_CTRL_2 = 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */ PHY_MARV_EXT_P_STAT = 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */ PHY_MARV_CABLE_DIAG = 0x1c,/* 16 bit r/o Cable Diagnostic Reg */ PHY_MARV_PAGE_ADDR = 0x1d,/* 16 bit r/w Extended Page Address Reg */ PHY_MARV_PAGE_DATA = 0x1e,/* 16 bit r/w Extended Page Data Reg */ /* for 10/100 Fast Ethernet PHY (88E3082 only) */ PHY_MARV_FE_LED_PAR = 0x16,/* 16 bit r/w LED Parallel Select Reg. */ PHY_MARV_FE_LED_SER = 0x17,/* 16 bit r/w LED Stream Select S. LED */ PHY_MARV_FE_VCT_TX = 0x1a,/* 16 bit r/w VCT Reg. for TXP/N Pins */ PHY_MARV_FE_VCT_RX = 0x1b,/* 16 bit r/o VCT Reg. for RXP/N Pins */ PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */ }; enum { PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */ PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */ PHY_CT_SPS_LSB = 1<<13, /* Bit 13: Speed select, lower bit */ PHY_CT_ANE = 1<<12, /* Bit 12: Auto-Negotiation Enabled */ PHY_CT_PDOWN = 1<<11, /* Bit 11: Power Down Mode */ PHY_CT_ISOL = 1<<10, /* Bit 10: Isolate Mode */ PHY_CT_RE_CFG = 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */ PHY_CT_DUP_MD = 1<<8, /* Bit 8: Duplex Mode */ PHY_CT_COL_TST = 1<<7, /* Bit 7: Collision Test enabled */ PHY_CT_SPS_MSB = 1<<6, /* Bit 6: Speed select, upper bit */ }; enum { PHY_CT_SP1000 = PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */ PHY_CT_SP100 = PHY_CT_SPS_LSB, /* enable speed of 100 Mbps */ PHY_CT_SP10 = 0, /* enable speed of 10 Mbps */ }; enum { PHY_ST_EXT_ST = 1<<8, /* Bit 8: Extended Status Present */ PHY_ST_PRE_SUP = 1<<6, /* Bit 6: Preamble Suppression */ PHY_ST_AN_OVER = 1<<5, /* Bit 5: Auto-Negotiation Over */ PHY_ST_REM_FLT = 1<<4, /* Bit 4: Remote Fault Condition Occured */ PHY_ST_AN_CAP = 1<<3, /* Bit 3: Auto-Negotiation Capability */ PHY_ST_LSYNC = 1<<2, /* Bit 2: Link Synchronized */ PHY_ST_JAB_DET = 1<<1, /* Bit 1: Jabber Detected */ PHY_ST_EXT_REG = 1<<0, /* Bit 0: Extended Register available */ }; enum { PHY_I1_OUI_MSK = 0x3f<<10, /* Bit 15..10: Organization Unique ID */ PHY_I1_MOD_NUM = 0x3f<<4, /* Bit 9.. 4: Model Number */ PHY_I1_REV_MSK = 0xf, /* Bit 3.. 0: Revision Number */ }; /* different Marvell PHY Ids */ enum { PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */ PHY_BCOM_ID1_A1 = 0x6041, PHY_BCOM_ID1_B2 = 0x6043, PHY_BCOM_ID1_C0 = 0x6044, PHY_BCOM_ID1_C5 = 0x6047, PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */ PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */ PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */ PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */ }; /* Advertisement register bits */ enum { PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */ PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */ PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */ PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */ PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */ PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */ PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */ PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */ PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */ PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */ PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */ PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/ PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA, PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL | PHY_AN_100HALF | PHY_AN_100FULL, }; /***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ /***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ enum { PHY_B_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */ PHY_B_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */ PHY_B_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */ PHY_B_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */ PHY_B_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */ PHY_B_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */ /* Bit 9..8: reserved */ PHY_B_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */ }; /** Marvell-Specific */ enum { PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */ PHY_M_AN_ACK = 1<<14, /* (ro) Acknowledge Received */ PHY_M_AN_RF = 1<<13, /* Remote Fault */ PHY_M_AN_ASP = 1<<11, /* Asymmetric Pause */ PHY_M_AN_PC = 1<<10, /* MAC Pause implemented */ PHY_M_AN_100_T4 = 1<<9, /* Not cap. 100Base-T4 (always 0) */ PHY_M_AN_100_FD = 1<<8, /* Advertise 100Base-TX Full Duplex */ PHY_M_AN_100_HD = 1<<7, /* Advertise 100Base-TX Half Duplex */ PHY_M_AN_10_FD = 1<<6, /* Advertise 10Base-TX Full Duplex */ PHY_M_AN_10_HD = 1<<5, /* Advertise 10Base-TX Half Duplex */ PHY_M_AN_SEL_MSK =0x1f<<4, /* Bit 4.. 0: Selector Field Mask */ }; /* special defines for FIBER (88E1011S only) */ enum { PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */ PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */ PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */ PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */ }; /* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */ enum { PHY_M_P_NO_PAUSE_X = 0<<7,/* Bit 8.. 7: no Pause Mode */ PHY_M_P_SYM_MD_X = 1<<7, /* Bit 8.. 7: symmetric Pause Mode */ PHY_M_P_ASYM_MD_X = 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */ PHY_M_P_BOTH_MD_X = 3<<7,/* Bit 8.. 7: both Pause Mode */ }; /***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/ enum { PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */ PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */ PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */ PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */ PHY_M_1000C_AFD = 1<<9, /* Advertise Full Duplex */ PHY_M_1000C_AHD = 1<<8, /* Advertise Half Duplex */ }; /***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/ enum { PHY_M_PC_TX_FFD_MSK = 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */ PHY_M_PC_RX_FFD_MSK = 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */ PHY_M_PC_ASS_CRS_TX = 1<<11, /* Assert CRS on Transmit */ PHY_M_PC_FL_GOOD = 1<<10, /* Force Link Good */ PHY_M_PC_EN_DET_MSK = 3<<8,/* Bit 9.. 8: Energy Detect Mask */ PHY_M_PC_ENA_EXT_D = 1<<7, /* Enable Ext. Distance (10BT) */ PHY_M_PC_MDIX_MSK = 3<<5,/* Bit 6.. 5: MDI/MDIX Config. Mask */ PHY_M_PC_DIS_125CLK = 1<<4, /* Disable 125 CLK */ PHY_M_PC_MAC_POW_UP = 1<<3, /* MAC Power up */ PHY_M_PC_SQE_T_ENA = 1<<2, /* SQE Test Enabled */ PHY_M_PC_POL_R_DIS = 1<<1, /* Polarity Reversal Disabled */ PHY_M_PC_DIS_JABBER = 1<<0, /* Disable Jabber */ }; enum { PHY_M_PC_EN_DET = 2<<8, /* Energy Detect (Mode 1) */ PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */ }; #define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK) enum { PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */ PHY_M_PC_MAN_MDIX = 1, /* 01 = Manual MDIX configuration */ PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */ }; /* for 10/100 Fast Ethernet PHY (88E3082 only) */ enum { PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */ PHY_M_PC_ENA_ENE_DT = 1<<14, /* Enable Energy Detect (sense & pulse) */ PHY_M_PC_DIS_NLP_CK = 1<<13, /* Disable Normal Link Puls (NLP) Check */ PHY_M_PC_ENA_LIP_NP = 1<<12, /* Enable Link Partner Next Page Reg. */ PHY_M_PC_DIS_NLP_GN = 1<<11, /* Disable Normal Link Puls Generation */ PHY_M_PC_DIS_SCRAMB = 1<<9, /* Disable Scrambler */ PHY_M_PC_DIS_FEFI = 1<<8, /* Disable Far End Fault Indic. (FEFI) */ PHY_M_PC_SH_TP_SEL = 1<<6, /* Shielded Twisted Pair Select */ PHY_M_PC_RX_FD_MSK = 3<<2,/* Bit 3.. 2: Rx FIFO Depth Mask */ }; /***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/ enum { PHY_M_PS_SPEED_MSK = 3<<14, /* Bit 15..14: Speed Mask */ PHY_M_PS_SPEED_1000 = 1<<15, /* 10 = 1000 Mbps */ PHY_M_PS_SPEED_100 = 1<<14, /* 01 = 100 Mbps */ PHY_M_PS_SPEED_10 = 0, /* 00 = 10 Mbps */ PHY_M_PS_FULL_DUP = 1<<13, /* Full Duplex */ PHY_M_PS_PAGE_REC = 1<<12, /* Page Received */ PHY_M_PS_SPDUP_RES = 1<<11, /* Speed & Duplex Resolved */ PHY_M_PS_LINK_UP = 1<<10, /* Link Up */ PHY_M_PS_CABLE_MSK = 7<<7, /* Bit 9.. 7: Cable Length Mask */ PHY_M_PS_MDI_X_STAT = 1<<6, /* MDI Crossover Stat (1=MDIX) */ PHY_M_PS_DOWNS_STAT = 1<<5, /* Downshift Status (1=downsh.) */ PHY_M_PS_ENDET_STAT = 1<<4, /* Energy Detect Status (1=act) */ PHY_M_PS_TX_P_EN = 1<<3, /* Tx Pause Enabled */ PHY_M_PS_RX_P_EN = 1<<2, /* Rx Pause Enabled */ PHY_M_PS_POL_REV = 1<<1, /* Polarity Reversed */ PHY_M_PS_JABBER = 1<<0, /* Jabber */ }; #define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN) /* for 10/100 Fast Ethernet PHY (88E3082 only) */ enum { PHY_M_PS_DTE_DETECT = 1<<15, /* Data Terminal Equipment (DTE) Detected */ PHY_M_PS_RES_SPEED = 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */ }; enum { PHY_M_IS_AN_ERROR = 1<<15, /* Auto-Negotiation Error */ PHY_M_IS_LSP_CHANGE = 1<<14, /* Link Speed Changed */ PHY_M_IS_DUP_CHANGE = 1<<13, /* Duplex Mode Changed */ PHY_M_IS_AN_PR = 1<<12, /* Page Received */ PHY_M_IS_AN_COMPL = 1<<11, /* Auto-Negotiation Completed */ PHY_M_IS_LST_CHANGE = 1<<10, /* Link Status Changed */ PHY_M_IS_SYMB_ERROR = 1<<9, /* Symbol Error */ PHY_M_IS_FALSE_CARR = 1<<8, /* False Carrier */ PHY_M_IS_FIFO_ERROR = 1<<7, /* FIFO Overflow/Underrun Error */ PHY_M_IS_MDI_CHANGE = 1<<6, /* MDI Crossover Changed */ PHY_M_IS_DOWNSH_DET = 1<<5, /* Downshift Detected */ PHY_M_IS_END_CHANGE = 1<<4, /* Energy Detect Changed */ PHY_M_IS_DTE_CHANGE = 1<<2, /* DTE Power Det. Status Changed */ PHY_M_IS_POL_CHANGE = 1<<1, /* Polarity Changed */ PHY_M_IS_JABBER = 1<<0, /* Jabber */ PHY_M_DEF_MSK = PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR, PHY_M_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL, }; /***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/ enum { PHY_M_EC_ENA_BC_EXT = 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */ PHY_M_EC_ENA_LIN_LB = 1<<14, /* Enable Line Loopback (88E1111 only) */ PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */ PHY_M_EC_M_DSC_MSK = 3<<10, /* Bit 11..10: Master Downshift Counter */ /* (88E1011 only) */ PHY_M_EC_S_DSC_MSK = 3<<8,/* Bit 9.. 8: Slave Downshift Counter */ /* (88E1011 only) */ PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9: Master Downshift Counter */ /* (88E1111 only) */ PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */ /* !!! Errata in spec. (1 = disable) */ PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/ PHY_M_EC_MAC_S_MSK = 7<<4,/* Bit 6.. 4: Def. MAC interface speed */ PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */ PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */ PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */ PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */}; #define PHY_M_EC_M_DSC(x) ((x)<<10 & PHY_M_EC_M_DSC_MSK) /* 00=1x; 01=2x; 10=3x; 11=4x */ #define PHY_M_EC_S_DSC(x) ((x)<<8 & PHY_M_EC_S_DSC_MSK) /* 00=dis; 01=1x; 10=2x; 11=3x */ #define PHY_M_EC_DSC_2(x) ((x)<<9 & PHY_M_EC_M_DSC_MSK2) /* 000=1x; 001=2x; 010=3x; 011=4x */ #define PHY_M_EC_MAC_S(x) ((x)<<4 & PHY_M_EC_MAC_S_MSK) /* 01X=0; 110=2.5; 111=25 (MHz) */ /* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */ enum { PHY_M_PC_DIS_LINK_Pa = 1<<15,/* Disable Link Pulses */ PHY_M_PC_DSC_MSK = 7<<12,/* Bit 14..12: Downshift Counter */ PHY_M_PC_DOWN_S_ENA = 1<<11,/* Downshift Enable */ }; /* !!! Errata in spec. (1 = disable) */ #define PHY_M_PC_DSC(x) (((x)<<12) & PHY_M_PC_DSC_MSK) /* 100=5x; 101=6x; 110=7x; 111=8x */ enum { MAC_TX_CLK_0_MHZ = 2, MAC_TX_CLK_2_5_MHZ = 6, MAC_TX_CLK_25_MHZ = 7, }; /***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/ enum { PHY_M_LEDC_DIS_LED = 1<<15, /* Disable LED */ PHY_M_LEDC_PULS_MSK = 7<<12,/* Bit 14..12: Pulse Stretch Mask */ PHY_M_LEDC_F_INT = 1<<11, /* Force Interrupt */ PHY_M_LEDC_BL_R_MSK = 7<<8,/* Bit 10.. 8: Blink Rate Mask */ PHY_M_LEDC_DP_C_LSB = 1<<7, /* Duplex Control (LSB, 88E1111 only) */ PHY_M_LEDC_TX_C_LSB = 1<<6, /* Tx Control (LSB, 88E1111 only) */ PHY_M_LEDC_LK_C_MSK = 7<<3,/* Bit 5.. 3: Link Control Mask */ /* (88E1111 only) */ }; enum { PHY_M_LEDC_LINK_MSK = 3<<3,/* Bit 4.. 3: Link Control Mask */ /* (88E1011 only) */ PHY_M_LEDC_DP_CTRL = 1<<2, /* Duplex Control */ PHY_M_LEDC_DP_C_MSB = 1<<2, /* Duplex Control (MSB, 88E1111 only) */ PHY_M_LEDC_RX_CTRL = 1<<1, /* Rx Activity / Link */ PHY_M_LEDC_TX_CTRL = 1<<0, /* Tx Activity / Link */ PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */ }; #define PHY_M_LED_PULS_DUR(x) (((x)<<12) & PHY_M_LEDC_PULS_MSK) /***** PHY_MARV_PHY_STAT (page 3)16 bit r/w Polarity Control Reg. *****/ enum { PHY_M_POLC_LS1M_MSK = 0xf<<12, /* Bit 15..12: LOS,STAT1 Mix % Mask */ PHY_M_POLC_IS0M_MSK = 0xf<<8, /* Bit 11.. 8: INIT,STAT0 Mix % Mask */ PHY_M_POLC_LOS_MSK = 0x3<<6, /* Bit 7.. 6: LOS Pol. Ctrl. Mask */ PHY_M_POLC_INIT_MSK = 0x3<<4, /* Bit 5.. 4: INIT Pol. Ctrl. Mask */ PHY_M_POLC_STA1_MSK = 0x3<<2, /* Bit 3.. 2: STAT1 Pol. Ctrl. Mask */ PHY_M_POLC_STA0_MSK = 0x3, /* Bit 1.. 0: STAT0 Pol. Ctrl. Mask */ }; #define PHY_M_POLC_LS1_P_MIX(x) (((x)<<12) & PHY_M_POLC_LS1M_MSK) #define PHY_M_POLC_IS0_P_MIX(x) (((x)<<8) & PHY_M_POLC_IS0M_MSK) #define PHY_M_POLC_LOS_CTRL(x) (((x)<<6) & PHY_M_POLC_LOS_MSK) #define PHY_M_POLC_INIT_CTRL(x) (((x)<<4) & PHY_M_POLC_INIT_MSK) #define PHY_M_POLC_STA1_CTRL(x) (((x)<<2) & PHY_M_POLC_STA1_MSK) #define PHY_M_POLC_STA0_CTRL(x) (((x)<<0) & PHY_M_POLC_STA0_MSK) enum { PULS_NO_STR = 0,/* no pulse stretching */ PULS_21MS = 1,/* 21 ms to 42 ms */ PULS_42MS = 2,/* 42 ms to 84 ms */ PULS_84MS = 3,/* 84 ms to 170 ms */ PULS_170MS = 4,/* 170 ms to 340 ms */ PULS_340MS = 5,/* 340 ms to 670 ms */ PULS_670MS = 6,/* 670 ms to 1.3 s */ PULS_1300MS = 7,/* 1.3 s to 2.7 s */ }; #define PHY_M_LED_BLINK_RT(x) (((x)<<8) & PHY_M_LEDC_BL_R_MSK) enum { BLINK_42MS = 0,/* 42 ms */ BLINK_84MS = 1,/* 84 ms */ BLINK_170MS = 2,/* 170 ms */ BLINK_340MS = 3,/* 340 ms */ BLINK_670MS = 4,/* 670 ms */ }; /***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/ #define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */ /* Bit 13..12: reserved */ #define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */ #define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */ #define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */ #define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */ #define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */ #define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */ enum { MO_LED_NORM = 0, MO_LED_BLINK = 1, MO_LED_OFF = 2, MO_LED_ON = 3, }; /***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/ enum { PHY_M_EC2_FI_IMPED = 1<<6, /* Fiber Input Impedance */ PHY_M_EC2_FO_IMPED = 1<<5, /* Fiber Output Impedance */ PHY_M_EC2_FO_M_CLK = 1<<4, /* Fiber Mode Clock Enable */ PHY_M_EC2_FO_BOOST = 1<<3, /* Fiber Output Boost */ PHY_M_EC2_FO_AM_MSK = 7,/* Bit 2.. 0: Fiber Output Amplitude */ }; /***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/ enum { PHY_M_FC_AUTO_SEL = 1<<15, /* Fiber/Copper Auto Sel. Dis. */ PHY_M_FC_AN_REG_ACC = 1<<14, /* Fiber/Copper AN Reg. Access */ PHY_M_FC_RESOLUTION = 1<<13, /* Fiber/Copper Resolution */ PHY_M_SER_IF_AN_BP = 1<<12, /* Ser. IF AN Bypass Enable */ PHY_M_SER_IF_BP_ST = 1<<11, /* Ser. IF AN Bypass Status */ PHY_M_IRQ_POLARITY = 1<<10, /* IRQ polarity */ PHY_M_DIS_AUT_MED = 1<<9, /* Disable Aut. Medium Reg. Selection */ /* (88E1111 only) */ PHY_M_UNDOC1 = 1<<7, /* undocumented bit !! */ PHY_M_DTE_POW_STAT = 1<<4, /* DTE Power Status (88E1111 only) */ PHY_M_MODE_MASK = 0xf, /* Bit 3.. 0: copy of HWCFG MODE[3:0] */ }; /* for 10/100 Fast Ethernet PHY (88E3082 only) */ /***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/ /* Bit 15..12: reserved (used internally) */ enum { PHY_M_FELP_LED2_MSK = 0xf<<8, /* Bit 11.. 8: LED2 Mask (LINK) */ PHY_M_FELP_LED1_MSK = 0xf<<4, /* Bit 7.. 4: LED1 Mask (ACT) */ PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */ }; #define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK) #define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK) #define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK) enum { LED_PAR_CTRL_COLX = 0x00, LED_PAR_CTRL_ERROR = 0x01, LED_PAR_CTRL_DUPLEX = 0x02, LED_PAR_CTRL_DP_COL = 0x03, LED_PAR_CTRL_SPEED = 0x04, LED_PAR_CTRL_LINK = 0x05, LED_PAR_CTRL_TX = 0x06, LED_PAR_CTRL_RX = 0x07, LED_PAR_CTRL_ACT = 0x08, LED_PAR_CTRL_LNK_RX = 0x09, LED_PAR_CTRL_LNK_AC = 0x0a, LED_PAR_CTRL_ACT_BL = 0x0b, LED_PAR_CTRL_TX_BL = 0x0c, LED_PAR_CTRL_RX_BL = 0x0d, LED_PAR_CTRL_COL_BL = 0x0e, LED_PAR_CTRL_INACT = 0x0f }; /*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/ enum { PHY_M_FESC_DIS_WAIT = 1<<2, /* Disable TDR Waiting Period */ PHY_M_FESC_ENA_MCLK = 1<<1, /* Enable MAC Rx Clock in sleep mode */ PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */ }; /* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */ /***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/ enum { PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */ PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */ PHY_M_MAC_MD_COPPER = 5,/* Copper only */ PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */ }; #define PHY_M_MAC_MODE_SEL(x) (((x)<<7) & PHY_M_MAC_MD_MSK) /***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/ enum { PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */ PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */ PHY_M_LEDC_STA1_MSK = 0xf<<4,/* Bit 7.. 4: STAT1 LED Ctrl. Mask */ PHY_M_LEDC_STA0_MSK = 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */ }; #define PHY_M_LEDC_LOS_CTRL(x) (((x)<<12) & PHY_M_LEDC_LOS_MSK) #define PHY_M_LEDC_INIT_CTRL(x) (((x)<<8) & PHY_M_LEDC_INIT_MSK) #define PHY_M_LEDC_STA1_CTRL(x) (((x)<<4) & PHY_M_LEDC_STA1_MSK) #define PHY_M_LEDC_STA0_CTRL(x) (((x)<<0) & PHY_M_LEDC_STA0_MSK) /* GMAC registers */ /* Port Registers */ enum { GM_GP_STAT = 0x0000, /* 16 bit r/o General Purpose Status */ GM_GP_CTRL = 0x0004, /* 16 bit r/w General Purpose Control */ GM_TX_CTRL = 0x0008, /* 16 bit r/w Transmit Control Reg. */ GM_RX_CTRL = 0x000c, /* 16 bit r/w Receive Control Reg. */ GM_TX_FLOW_CTRL = 0x0010, /* 16 bit r/w Transmit Flow-Control */ GM_TX_PARAM = 0x0014, /* 16 bit r/w Transmit Parameter Reg. */ GM_SERIAL_MODE = 0x0018, /* 16 bit r/w Serial Mode Register */ /* Source Address Registers */ GM_SRC_ADDR_1L = 0x001c, /* 16 bit r/w Source Address 1 (low) */ GM_SRC_ADDR_1M = 0x0020, /* 16 bit r/w Source Address 1 (middle) */ GM_SRC_ADDR_1H = 0x0024, /* 16 bit r/w Source Address 1 (high) */ GM_SRC_ADDR_2L = 0x0028, /* 16 bit r/w Source Address 2 (low) */ GM_SRC_ADDR_2M = 0x002c, /* 16 bit r/w Source Address 2 (middle) */ GM_SRC_ADDR_2H = 0x0030, /* 16 bit r/w Source Address 2 (high) */ /* Multicast Address Hash Registers */ GM_MC_ADDR_H1 = 0x0034, /* 16 bit r/w Multicast Address Hash 1 */ GM_MC_ADDR_H2 = 0x0038, /* 16 bit r/w Multicast Address Hash 2 */ GM_MC_ADDR_H3 = 0x003c, /* 16 bit r/w Multicast Address Hash 3 */ GM_MC_ADDR_H4 = 0x0040, /* 16 bit r/w Multicast Address Hash 4 */ /* Interrupt Source Registers */ GM_TX_IRQ_SRC = 0x0044, /* 16 bit r/o Tx Overflow IRQ Source */ GM_RX_IRQ_SRC = 0x0048, /* 16 bit r/o Rx Overflow IRQ Source */ GM_TR_IRQ_SRC = 0x004c, /* 16 bit r/o Tx/Rx Over. IRQ Source */ /* Interrupt Mask Registers */ GM_TX_IRQ_MSK = 0x0050, /* 16 bit r/w Tx Overflow IRQ Mask */ GM_RX_IRQ_MSK = 0x0054, /* 16 bit r/w Rx Overflow IRQ Mask */ GM_TR_IRQ_MSK = 0x0058, /* 16 bit r/w Tx/Rx Over. IRQ Mask */ /* Serial Management Interface (SMI) Registers */ GM_SMI_CTRL = 0x0080, /* 16 bit r/w SMI Control Register */ GM_SMI_DATA = 0x0084, /* 16 bit r/w SMI Data Register */ GM_PHY_ADDR = 0x0088, /* 16 bit r/w GPHY Address Register */ }; /* MIB Counters */ #define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */ #define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */ /* * MIB Counters base address definitions (low word) - * use offset 4 for access to high word (32 bit r/o) */ enum { GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */ GM_RXF_BC_OK = GM_MIB_CNT_BASE + 8, /* Broadcast Frames Received OK */ GM_RXF_MPAUSE = GM_MIB_CNT_BASE + 16, /* Pause MAC Ctrl Frames Received */ GM_RXF_MC_OK = GM_MIB_CNT_BASE + 24, /* Multicast Frames Received OK */ GM_RXF_FCS_ERR = GM_MIB_CNT_BASE + 32, /* Rx Frame Check Seq. Error */ /* GM_MIB_CNT_BASE + 40: reserved */ GM_RXO_OK_LO = GM_MIB_CNT_BASE + 48, /* Octets Received OK Low */ GM_RXO_OK_HI = GM_MIB_CNT_BASE + 56, /* Octets Received OK High */ GM_RXO_ERR_LO = GM_MIB_CNT_BASE + 64, /* Octets Received Invalid Low */ GM_RXO_ERR_HI = GM_MIB_CNT_BASE + 72, /* Octets Received Invalid High */ GM_RXF_SHT = GM_MIB_CNT_BASE + 80, /* Frames <64 Byte Received OK */ GM_RXE_FRAG = GM_MIB_CNT_BASE + 88, /* Frames <64 Byte Received with FCS Err */ GM_RXF_64B = GM_MIB_CNT_BASE + 96, /* 64 Byte Rx Frame */ GM_RXF_127B = GM_MIB_CNT_BASE + 104, /* 65-127 Byte Rx Frame */ GM_RXF_255B = GM_MIB_CNT_BASE + 112, /* 128-255 Byte Rx Frame */ GM_RXF_511B = GM_MIB_CNT_BASE + 120, /* 256-511 Byte Rx Frame */ GM_RXF_1023B = GM_MIB_CNT_BASE + 128, /* 512-1023 Byte Rx Frame */ GM_RXF_1518B = GM_MIB_CNT_BASE + 136, /* 1024-1518 Byte Rx Frame */ GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144, /* 1519-MaxSize Byte Rx Frame */ GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152, /* Rx Frame too Long Error */ GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160, /* Rx Jabber Packet Frame */ /* GM_MIB_CNT_BASE + 168: reserved */ GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176, /* Rx FIFO overflow Event */ /* GM_MIB_CNT_BASE + 184: reserved */ GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192, /* Unicast Frames Xmitted OK */ GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200, /* Broadcast Frames Xmitted OK */ GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208, /* Pause MAC Ctrl Frames Xmitted */ GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216, /* Multicast Frames Xmitted OK */ GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224, /* Octets Transmitted OK Low */ GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232, /* Octets Transmitted OK High */ GM_TXF_64B = GM_MIB_CNT_BASE + 240, /* 64 Byte Tx Frame */ GM_TXF_127B = GM_MIB_CNT_BASE + 248, /* 65-127 Byte Tx Frame */ GM_TXF_255B = GM_MIB_CNT_BASE + 256, /* 128-255 Byte Tx Frame */ GM_TXF_511B = GM_MIB_CNT_BASE + 264, /* 256-511 Byte Tx Frame */ GM_TXF_1023B = GM_MIB_CNT_BASE + 272, /* 512-1023 Byte Tx Frame */ GM_TXF_1518B = GM_MIB_CNT_BASE + 280, /* 1024-1518 Byte Tx Frame */ GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288, /* 1519-MaxSize Byte Tx Frame */ GM_TXF_COL = GM_MIB_CNT_BASE + 304, /* Tx Collision */ GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312, /* Tx Late Collision */ GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320, /* Tx aborted due to Exces. Col. */ GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328, /* Tx Multiple Collision */ GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336, /* Tx Single Collision */ GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344, /* Tx FIFO Underrun Event */ }; /* GMAC Bit Definitions */ /* GM_GP_STAT 16 bit r/o General Purpose Status Register */ enum { GM_GPSR_SPEED = 1<<15, /* Bit 15: Port Speed (1 = 100 Mbps) */ GM_GPSR_DUPLEX = 1<<14, /* Bit 14: Duplex Mode (1 = Full) */ GM_GPSR_FC_TX_DIS = 1<<13, /* Bit 13: Tx Flow-Control Mode Disabled */ GM_GPSR_LINK_UP = 1<<12, /* Bit 12: Link Up Status */ GM_GPSR_PAUSE = 1<<11, /* Bit 11: Pause State */ GM_GPSR_TX_ACTIVE = 1<<10, /* Bit 10: Tx in Progress */ GM_GPSR_EXC_COL = 1<<9, /* Bit 9: Excessive Collisions Occured */ GM_GPSR_LAT_COL = 1<<8, /* Bit 8: Late Collisions Occured */ GM_GPSR_PHY_ST_CH = 1<<5, /* Bit 5: PHY Status Change */ GM_GPSR_GIG_SPEED = 1<<4, /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */ GM_GPSR_PART_MODE = 1<<3, /* Bit 3: Partition mode */ GM_GPSR_FC_RX_DIS = 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */ GM_GPSR_PROM_EN = 1<<1, /* Bit 1: Promiscuous Mode Enabled */ }; /* GM_GP_CTRL 16 bit r/w General Purpose Control Register */ enum { GM_GPCR_PROM_ENA = 1<<14, /* Bit 14: Enable Promiscuous Mode */ GM_GPCR_FC_TX_DIS = 1<<13, /* Bit 13: Disable Tx Flow-Control Mode */ GM_GPCR_TX_ENA = 1<<12, /* Bit 12: Enable Transmit */ GM_GPCR_RX_ENA = 1<<11, /* Bit 11: Enable Receive */ GM_GPCR_BURST_ENA = 1<<10, /* Bit 10: Enable Burst Mode */ GM_GPCR_LOOP_ENA = 1<<9, /* Bit 9: Enable MAC Loopback Mode */ GM_GPCR_PART_ENA = 1<<8, /* Bit 8: Enable Partition Mode */ GM_GPCR_GIGS_ENA = 1<<7, /* Bit 7: Gigabit Speed (1000 Mbps) */ GM_GPCR_FL_PASS = 1<<6, /* Bit 6: Force Link Pass */ GM_GPCR_DUP_FULL = 1<<5, /* Bit 5: Full Duplex Mode */ GM_GPCR_FC_RX_DIS = 1<<4, /* Bit 4: Disable Rx Flow-Control Mode */ GM_GPCR_SPEED_100 = 1<<3, /* Bit 3: Port Speed 100 Mbps */ GM_GPCR_AU_DUP_DIS = 1<<2, /* Bit 2: Disable Auto-Update Duplex */ GM_GPCR_AU_FCT_DIS = 1<<1, /* Bit 1: Disable Auto-Update Flow-C. */ GM_GPCR_AU_SPD_DIS = 1<<0, /* Bit 0: Disable Auto-Update Speed */ }; #define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100) #define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS) /* GM_TX_CTRL 16 bit r/w Transmit Control Register */ enum { GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */ GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */ GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */ GM_TXCR_COL_THR_MSK = 1<<10, /* Bit 12..10: Collision Threshold */ }; #define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK) #define TX_COL_DEF 0x04 /* GM_RX_CTRL 16 bit r/w Receive Control Register */ enum { GM_RXCR_UCF_ENA = 1<<15, /* Bit 15: Enable Unicast filtering */ GM_RXCR_MCF_ENA = 1<<14, /* Bit 14: Enable Multicast filtering */ GM_RXCR_CRC_DIS = 1<<13, /* Bit 13: Remove 4-byte CRC */ GM_RXCR_PASS_FC = 1<<12, /* Bit 12: Pass FC packets to FIFO */ }; /* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */ enum { GM_TXPA_JAMLEN_MSK = 0x03<<14, /* Bit 15..14: Jam Length */ GM_TXPA_JAMIPG_MSK = 0x1f<<9, /* Bit 13..9: Jam IPG */ GM_TXPA_JAMDAT_MSK = 0x1f<<4, /* Bit 8..4: IPG Jam to Data */ GM_TXPA_BO_LIM_MSK = 0x0f, /* Bit 3.. 0: Backoff Limit Mask */ TX_JAM_LEN_DEF = 0x03, TX_JAM_IPG_DEF = 0x0b, TX_IPG_JAM_DEF = 0x1c, TX_BOF_LIM_DEF = 0x04, }; #define TX_JAM_LEN_VAL(x) (((x)<<14) & GM_TXPA_JAMLEN_MSK) #define TX_JAM_IPG_VAL(x) (((x)<<9) & GM_TXPA_JAMIPG_MSK) #define TX_IPG_JAM_DATA(x) (((x)<<4) & GM_TXPA_JAMDAT_MSK) #define TX_BACK_OFF_LIM(x) ((x) & GM_TXPA_BO_LIM_MSK) /* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */ enum { GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */ GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */ GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */ GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */ GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */ }; #define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK) #define DATA_BLIND_DEF 0x04 #define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK) #define IPG_DATA_DEF 0x1e /* GM_SMI_CTRL 16 bit r/w SMI Control Register */ enum { GM_SMI_CT_PHY_A_MSK = 0x1f<<11,/* Bit 15..11: PHY Device Address */ GM_SMI_CT_REG_A_MSK = 0x1f<<6,/* Bit 10.. 6: PHY Register Address */ GM_SMI_CT_OP_RD = 1<<5, /* Bit 5: OpCode Read (0=Write)*/ GM_SMI_CT_RD_VAL = 1<<4, /* Bit 4: Read Valid (Read completed) */ GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */ }; #define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK) #define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK) /* GM_PHY_ADDR 16 bit r/w GPHY Address Register */ enum { GM_PAR_MIB_CLR = 1<<5, /* Bit 5: Set MIB Clear Counter Mode */ GM_PAR_MIB_TST = 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */ }; /* Receive Frame Status Encoding */ enum { GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */ GMR_FS_VLAN = 1<<13, /* VLAN Packet */ GMR_FS_JABBER = 1<<12, /* Jabber Packet */ GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */ GMR_FS_MC = 1<<10, /* Multicast Packet */ GMR_FS_BC = 1<<9, /* Broadcast Packet */ GMR_FS_RX_OK = 1<<8, /* Receive OK (Good Packet) */ GMR_FS_GOOD_FC = 1<<7, /* Good Flow-Control Packet */ GMR_FS_BAD_FC = 1<<6, /* Bad Flow-Control Packet */ GMR_FS_MII_ERR = 1<<5, /* MII Error */ GMR_FS_LONG_ERR = 1<<4, /* Too Long Packet */ GMR_FS_FRAGMENT = 1<<3, /* Fragment */ GMR_FS_CRC_ERR = 1<<1, /* CRC Error */ GMR_FS_RX_FF_OV = 1<<0, /* Rx FIFO Overflow */ GMR_FS_ANY_ERR = GMR_FS_RX_FF_OV | GMR_FS_CRC_ERR | GMR_FS_FRAGMENT | GMR_FS_LONG_ERR | GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC | GMR_FS_UN_SIZE | GMR_FS_JABBER, }; /* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */ enum { RX_TRUNC_ON = 1<<27, /* enable packet truncation */ RX_TRUNC_OFF = 1<<26, /* disable packet truncation */ RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */ RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */ GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */ GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */ GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */ GMF_RP_TST_ON = 1<<10, /* Read Pointer Test On */ GMF_RP_TST_OFF = 1<<9, /* Read Pointer Test Off */ GMF_RP_STEP = 1<<8, /* Read Pointer Step/Increment */ GMF_RX_F_FL_ON = 1<<7, /* Rx FIFO Flush Mode On */ GMF_RX_F_FL_OFF = 1<<6, /* Rx FIFO Flush Mode Off */ GMF_CLI_RX_FO = 1<<5, /* Clear IRQ Rx FIFO Overrun */ GMF_CLI_RX_C = 1<<4, /* Clear IRQ Rx Frame Complete */ GMF_OPER_ON = 1<<3, /* Operational Mode On */ GMF_OPER_OFF = 1<<2, /* Operational Mode Off */ GMF_RST_CLR = 1<<1, /* Clear GMAC FIFO Reset */ GMF_RST_SET = 1<<0, /* Set GMAC FIFO Reset */ RX_GMF_FL_THR_DEF = 0xa, /* flush threshold (default) */ GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON, }; /* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */ enum { TX_VLAN_TAG_ON = 1<<25,/* enable VLAN tagging */ TX_VLAN_TAG_OFF = 1<<24,/* disable VLAN tagging */ GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */ GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */ GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */ GMF_CLI_TX_FU = 1<<6, /* Clear IRQ Tx FIFO Underrun */ GMF_CLI_TX_FC = 1<<5, /* Clear IRQ Tx Frame Complete */ GMF_CLI_TX_PE = 1<<4, /* Clear IRQ Tx Parity Error */ }; /* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */ enum { GMT_ST_START = 1<<2, /* Start Time Stamp Timer */ GMT_ST_STOP = 1<<1, /* Stop Time Stamp Timer */ GMT_ST_CLR_IRQ = 1<<0, /* Clear Time Stamp Timer IRQ */ }; /* B28_Y2_ASF_STAT_CMD 32 bit ASF Status and Command Reg */ enum { Y2_ASF_OS_PRES = 1<<4, /* ASF operation system present */ Y2_ASF_RESET = 1<<3, /* ASF system in reset state */ Y2_ASF_RUNNING = 1<<2, /* ASF system operational */ Y2_ASF_CLR_HSTI = 1<<1, /* Clear ASF IRQ */ Y2_ASF_IRQ = 1<<0, /* Issue an IRQ to ASF system */ Y2_ASF_UC_STATE = 3<<2, /* ASF uC State */ Y2_ASF_CLK_HALT = 0, /* ASF system clock stopped */ }; /* B28_Y2_ASF_HOST_COM 32 bit ASF Host Communication Reg */ enum { Y2_ASF_CLR_ASFI = 1<<1, /* Clear host IRQ */ Y2_ASF_HOST_IRQ = 1<<0, /* Issue an IRQ to HOST system */ }; /* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */ enum { SC_STAT_CLR_IRQ = 1<<4, /* Status Burst IRQ clear */ SC_STAT_OP_ON = 1<<3, /* Operational Mode On */ SC_STAT_OP_OFF = 1<<2, /* Operational Mode Off */ SC_STAT_RST_CLR = 1<<1, /* Clear Status Unit Reset (Enable) */ SC_STAT_RST_SET = 1<<0, /* Set Status Unit Reset */ }; /* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */ enum { GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */ GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */ GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */ GMC_F_LOOPB_OFF = 1<<4, /* FIFO Loopback Off */ GMC_PAUSE_ON = 1<<3, /* Pause On */ GMC_PAUSE_OFF = 1<<2, /* Pause Off */ GMC_RST_CLR = 1<<1, /* Clear GMAC Reset */ GMC_RST_SET = 1<<0, /* Set GMAC Reset */ }; /* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */ enum { GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */ GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */ GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */ GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */ GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */ GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */ GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */ GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */ GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */ GPC_ANEG_0 = 1<<19, /* ANEG[0] */ GPC_ENA_XC = 1<<18, /* Enable MDI crossover */ GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */ GPC_ANEG_3 = 1<<16, /* ANEG[3] */ GPC_ANEG_2 = 1<<15, /* ANEG[2] */ GPC_ANEG_1 = 1<<14, /* ANEG[1] */ GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */ GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */ GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */ GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */ GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */ GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */ /* Bits 7..2: reserved */ GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */ GPC_RST_SET = 1<<0, /* Set GPHY Reset */ }; /* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */ /* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */ enum { GM_IS_TX_CO_OV = 1<<5, /* Transmit Counter Overflow IRQ */ GM_IS_RX_CO_OV = 1<<4, /* Receive Counter Overflow IRQ */ GM_IS_TX_FF_UR = 1<<3, /* Transmit FIFO Underrun */ GM_IS_TX_COMPL = 1<<2, /* Frame Transmission Complete */ GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */ GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */ #define GMAC_DEF_MSK GM_IS_TX_FF_UR /* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */ /* Bits 15.. 2: reserved */ GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */ GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */ /* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */ WOL_CTL_LINK_CHG_OCC = 1<<15, WOL_CTL_MAGIC_PKT_OCC = 1<<14, WOL_CTL_PATTERN_OCC = 1<<13, WOL_CTL_CLEAR_RESULT = 1<<12, WOL_CTL_ENA_PME_ON_LINK_CHG = 1<<11, WOL_CTL_DIS_PME_ON_LINK_CHG = 1<<10, WOL_CTL_ENA_PME_ON_MAGIC_PKT = 1<<9, WOL_CTL_DIS_PME_ON_MAGIC_PKT = 1<<8, WOL_CTL_ENA_PME_ON_PATTERN = 1<<7, WOL_CTL_DIS_PME_ON_PATTERN = 1<<6, WOL_CTL_ENA_LINK_CHG_UNIT = 1<<5, WOL_CTL_DIS_LINK_CHG_UNIT = 1<<4, WOL_CTL_ENA_MAGIC_PKT_UNIT = 1<<3, WOL_CTL_DIS_MAGIC_PKT_UNIT = 1<<2, WOL_CTL_ENA_PATTERN_UNIT = 1<<1, WOL_CTL_DIS_PATTERN_UNIT = 1<<0, }; #define WOL_CTL_DEFAULT \ (WOL_CTL_DIS_PME_ON_LINK_CHG | \ WOL_CTL_DIS_PME_ON_PATTERN | \ WOL_CTL_DIS_PME_ON_MAGIC_PKT | \ WOL_CTL_DIS_LINK_CHG_UNIT | \ WOL_CTL_DIS_PATTERN_UNIT | \ WOL_CTL_DIS_MAGIC_PKT_UNIT) /* WOL_MATCH_CTL 8 bit WOL Match Control Reg */ #define WOL_CTL_PATT_ENA(x) (1 << (x)) /* Control flags */ enum { UDPTCP = 1<<0, CALSUM = 1<<1, WR_SUM = 1<<2, INIT_SUM= 1<<3, LOCK_SUM= 1<<4, INS_VLAN= 1<<5, FRC_STAT= 1<<6, EOP = 1<<7, }; enum { HW_OWNER = 1<<7, OP_TCPWRITE = 0x11, OP_TCPSTART = 0x12, OP_TCPINIT = 0x14, OP_TCPLCK = 0x18, OP_TCPCHKSUM = OP_TCPSTART, OP_TCPIS = OP_TCPINIT | OP_TCPSTART, OP_TCPLW = OP_TCPLCK | OP_TCPWRITE, OP_TCPLSW = OP_TCPLCK | OP_TCPSTART | OP_TCPWRITE, OP_TCPLISW = OP_TCPLCK | OP_TCPINIT | OP_TCPSTART | OP_TCPWRITE, OP_ADDR64 = 0x21, OP_VLAN = 0x22, OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN, OP_LRGLEN = 0x24, OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN, OP_BUFFER = 0x40, OP_PACKET = 0x41, OP_LARGESEND = 0x43, /* YUKON-2 STATUS opcodes defines */ OP_RXSTAT = 0x60, OP_RXTIMESTAMP = 0x61, OP_RXVLAN = 0x62, OP_RXCHKS = 0x64, OP_RXCHKSVLAN = OP_RXCHKS | OP_RXVLAN, OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN, OP_RSS_HASH = 0x65, OP_TXINDEXLE = 0x68, }; /* Yukon 2 hardware interface * Not tested on big endian */ struct sky2_tx_le { union { u32 addr; struct { u16 offset; u16 start; } csum __attribute((packed)); struct { u16 size; u16 rsvd; } tso __attribute((packed)); } tx; u16 length; /* also vlan tag or checksum start */ u8 ctrl; u8 opcode; } __attribute((packed)); struct sky2_rx_le { u32 addr; u16 length; u8 ctrl; u8 opcode; } __attribute((packed));; struct sky2_status_le { u32 status; /* also checksum */ u16 length; /* also vlan tag */ u8 link; u8 opcode; } __attribute((packed)); struct ring_info { struct sk_buff *skb; dma_addr_t mapaddr; u16 maplen; u16 idx; }; struct sky2_port { struct sky2_hw *hw; struct net_device *netdev; unsigned port; u32 msg_enable; struct ring_info *tx_ring; struct sky2_tx_le *tx_le; spinlock_t tx_lock; u32 tx_addr64; u16 tx_cons; /* next le to check */ u16 tx_prod; /* next le to use */ u16 tx_pending; u16 tx_last_put; u16 tx_last_mss; struct ring_info *rx_ring; struct sky2_rx_le *rx_le; u32 rx_addr64; u16 rx_next; /* next re to check */ u16 rx_put; /* next le index to use */ u16 rx_pending; u16 rx_last_put; #ifdef SKY2_VLAN_TAG_USED u16 rx_tag; struct vlan_group *vlgrp; #endif dma_addr_t rx_le_map; dma_addr_t tx_le_map; u32 advertising; /* ADVERTISED_ bits */ u16 speed; /* SPEED_1000, SPEED_100, ... */ u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */ u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */ u8 rx_pause; u8 tx_pause; u8 rx_csum; u8 wol; struct tasklet_struct phy_task; struct net_device_stats net_stats; }; struct sky2_hw { void __iomem *regs; struct pci_dev *pdev; u32 intr_mask; struct net_device *dev[2]; int pm_cap; u8 chip_id; u8 chip_rev; u8 copper; u8 ports; struct sky2_status_le *st_le; u32 st_idx; dma_addr_t st_dma; spinlock_t phy_lock; }; /* Register accessor for memory mapped device */ static inline u32 sky2_read32(const struct sky2_hw *hw, unsigned reg) { return readl(hw->regs + reg); } static inline u16 sky2_read16(const struct sky2_hw *hw, unsigned reg) { return readw(hw->regs + reg); } static inline u8 sky2_read8(const struct sky2_hw *hw, unsigned reg) { return readb(hw->regs + reg); } /* This should probably go away, bus based tweeks suck */ static inline int is_pciex(const struct sky2_hw *hw) { u32 status; pci_read_config_dword(hw->pdev, PCI_DEV_STATUS, &status); return (status & PCI_OS_PCI_X) == 0; } static inline void sky2_write32(const struct sky2_hw *hw, unsigned reg, u32 val) { writel(val, hw->regs + reg); } static inline void sky2_write16(const struct sky2_hw *hw, unsigned reg, u16 val) { writew(val, hw->regs + reg); } static inline void sky2_write8(const struct sky2_hw *hw, unsigned reg, u8 val) { writeb(val, hw->regs + reg); } /* Yukon PHY related registers */ #define SK_GMAC_REG(port,reg) \ (BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg)) #define GM_PHY_RETRIES 100 static inline u16 gma_read16(const struct sky2_hw *hw, unsigned port, unsigned reg) { return sky2_read16(hw, SK_GMAC_REG(port,reg)); } static inline u32 gma_read32(struct sky2_hw *hw, unsigned port, unsigned reg) { unsigned base = SK_GMAC_REG(port, reg); return (u32) sky2_read16(hw, base) | (u32) sky2_read16(hw, base+4) << 16; } static inline void gma_write16(const struct sky2_hw *hw, unsigned port, int r, u16 v) { sky2_write16(hw, SK_GMAC_REG(port,r), v); } static inline void gma_set_addr(struct sky2_hw *hw, unsigned port, unsigned reg, const u8 *addr) { gma_write16(hw, port, reg, (u16) addr[0] | ((u16) addr[1] << 8)); gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8)); gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8)); } #endif