Change version number. Still don't have enough history on this
to call it 1.0 yet.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Under load, my SysKonnect SK-9S22 sees duplicate checksums from
earlier packets. Doesn't happen on other platforms so just disable
receive checksum there.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Turn symmetric flow control on by default. This was an oversight
in the initial versions.
Signed-off-by: Stephen HEmminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a couple more prefetches to where we walk the rings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Put more logic in to try and handle transmit timeout recovery.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adjust interrupt deferral values for better performance and avoid
starvation issues under stress.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Optimize poll routine by not clearing interrupt till after
processing, and checking for more work before re-enable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change transmit complete handling to use the status values
in the poll list because they are in-cache, rather than reading
non-cached memory for chips status.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some transmit side small fixes:
* When computing number of list elements per transmit, do full
comparision to check for checksuming.
* Get rid of racy check for tx_complete
* Change stop test to match wake condition.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Split Tx and Rx ring into two different data structures.
Tx needs the next value (to handle partial status), and
Rx always needs the mapaddr (to handle resubmitting same buffer).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to keep track of mapping length in ring structure
because we can get the same info from other info.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to disable interrupts during the transmit routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do phy processing in a work queue rather than a tasklet.
This means we can let bottom halves run.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support for get/set the interrupt coalescing settings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make the copy threshold a module parameter for those who
may want to turn it off.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
It is a useful optimization to rearrange the structure
slightly to align receive and transmit portions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There maybe new versions of Yukon2 in the future, so make the
driver more robust to handle this.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[ Move assosciated code comment to the correct spot, and
update driver version and release date -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the rearrangements dropped this and it means
sky2 spins in napi/interrupt.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Sky2 update changed name of netif_schedule_test to __netif_schedule_prep
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There are currently two IPW_DEBUG options in drivers/net/wireless/Kconfig
(one for ipw2100 and one for ipw2200). The attached patch splits it into
IPW2100_DEBUG and IPW2200_DEBUG.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Cc: "James P. Ketrenos" <ipw2100-admin@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Use kzalloc for IPW2200
- Fix config dependency for IPW2200
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Yi Zhu <yi.zhu@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hello Jeff,
this patch changes causes the airo driver to not reset the card when a
temporary WEP key is set, when the IW_ENCODE_TEMP flag is used. This is
needed for xsupplicant as 802.1x, LEAP, etc. change WEP keys frequently
after authentication and resetting the card causes infinite
reauthentication.
Javier and Jean agree with the patch, Javier suggested I send this to
you, can you apply this?
Thanks.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
without this patch after an rmmod, modprobe the card won't work anymore
until the next reboot.
This patch seem safe to apply for all cards as the bsd driver already do
that.
I had to add a timeout because strange things happen (issuecommand will
fail) if the card is already reseted (after a reboot).
PS : it seems there are missing reset when leaving monitor mode...
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
If using UDP over VLAN, with the skge driver there is a possibility
of generating an incorrect checksum. This is a unlikely occurrence
because it is only an issue on Yukon revision 0, and that revision
doesn't seem to exist on any current hardware (probably early prototype).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Power management parameters could not be set by iwconfig due to
incorrect error handling.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use platform_driver_unregister not driver_unregister to unregister a
struct platform_driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Disable/enable the SERDES carrier when an interface is administratively
downed/upped.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement pm3386 reset. A reset zeroes out the internally stored MAC
addresses, so we need to save and reload them by hand.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a pm3386 hook for disabling/enabling the SERDES carrier, so that
we can disable it when the interface is administratively downed, and
enable it when it is upped.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When we reset the pm3386, it loses its internally stored MAC addresses
that were programmed into it by the bootloader (and are used by the
hardware for the generation of PAUSE frames.) Add a hook to allow
setting these addresses so that we can program them back by hand.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After initialising, report the MAC address that we're using for
each port.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We assign nds[i] to a local variable 'dev', which we never use
afterwards. Use the local variable instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Even after an interface has gone !netif_running(), we still want to
catch the 'carrier went down' event for our internal bookkeeping.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sky2 driver introduced netif_rx_schedule_test(). This is
exactly what we need, so remove our local version of this function
(which was called netif_rx_schedule_prep_notup) and use the generic
one instead.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make caleb.c and pm3386.c include their own header files, to catch
incorrect prototype definitions.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
