o Defined error code such as fw not responding, test already running and
cable not connected.
o Check Fw capability before performing loopback test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as skb is given to hardware, TX completion can free skb under us.
Therefore, we should update dev stats before kicking the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC learning is required in bridge mode.
During bridge mode device will be put in promiscous mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added QME8242-k 10GbE Dual Port Mezzanine Card to supported card info.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip reset logic (IDC logic) has changed with fw dump support.
This broked compatibility with driver using older IDC logic.
Changes to make it compatible with drivers using older IDC logic.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratchpad location that we were reading from has not been
initialized yet during ->probe(), so we were getting inaccurate
information.
Update version to 2.1.10.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to help debug issues related to management firmware.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to allow iSCSI connection to fail faster instead of waiting for the
long timeout.
Update version to 2.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest bnx2x driver uses different CID for the iSCSI rings, so
we need to pass it in the ring init data. The rx ring is also
zeroed out to prevent stale DMA addresses from being used after
shutdown.
The same cp local variable redefined inside the else branch is
also eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHIP_2_PORT_MODE was not set correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested by Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver state (and power source) is being more intensely
scrutinized, we need to make sure it is correct 100% of the time. This
patch finds and fixes all dangling power state transitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to update the status of the function to a common
location to the critical section added in the previous patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that performs the power source switching will need to consider
the status of the other devices before making any switches. The status
updates and power source switching will need to be an atomic operation,
so a critical section will be needed. This patch establishes the
critical section through a CPMU mutex.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 devices will need to know exactly what function number they are so
that they can communicate their status to the other functions. In a KVM
environment, the function number of a device presented by the kernel
might not be the true function number, so an alternative method to
determine the function number is needed.
This patch used to contain an implementation for the alternative method,
but recently we discovered a hardware bug that renders it incorrect.
While new method is not yet known, it is still useful to consolidate the
code that determines the PCI function to one location and use the
results throughout the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently pci_set_power_state() does not return useful return codes for
transitions to the D0 power state. If a device refuses to go into D0,
the PCI layer issues a warning but returns success.
Entering into D0 is a requirement for correct operation of tg3 devices
though. If the PCI layer should be changed to return an error code for
this type of failure, the tg3 driver would be interested in catching it
and reacting to it. This patch makes the necessary modifications.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver is going to require memory mapped register access much
sooner than before. This patch makes sure the device is in the D0 power
state as soon as possible, and moves the code that enables the memory
arbiter outside tg3_get_eeprom_hw_cfg() where it can be more easily
monitored.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch will require the driver to communicate with the APE
much sooner than before. This patch make sure the APE registers are
memory mapped and that the ENABLE_APE bit is set before the first use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we flush tp_status and then flush the remainder of the header+payload.
tp_status should be flushed in the end to avoid stale data being read by user-space.
Incorrectly re-ordered barriers in v1.
Signed-off-by: Chetan Loke <loke.chetan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:
1) dynamic allocation
2) attachment to dst->hh
3) refcounting
Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix use of static variable in rpcb_getport_async
NFSv4.1: update nfs4_fattr_bitmap_maxsz
SUNRPC: Fix a race between work-queue and rpc_killall_tasks
pnfs: write: Set mds_offset in the generic layer - it is needed by all LDs
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/evergreen: emit SQ_LDS_RESOURCE_MGMT for blits
agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
drm/radeon/kms: fix typo in read_disabled vbios code
drm/radeon/kms: use correct BUS_CNTL reg on rs600
drm/radeon/kms: fix backend map typo on juniper
drm/radeon/kms: fix regression in hotplug
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc39
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This following code contains a dead "if (dev).." block:
...
for (i = 0; i < slip_maxdev; i++) {
dev = slip_devs[i];
if (dev == NULL)
break;
}
/* Sorry, too many, all slots in use */
if (i >= slip_maxdev)
return NULL;
if (dev) {
sl = netdev_priv(dev);
if (test_bit(SLF_INUSE, &sl->flags)) {
unregister_netdevice(dev);
dev = NULL;
slip_devs[i] = NULL;
}
}
...
The reason is that the code starting with "if (dev).." is never called as
when we found an empty slot (dev == NULL) we break the loop and "if (dev).."
not works eiter the loop ends and we get out with "i >= slip_maxdev".
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As slip_devs is initialized on module load stage there is no reason to
check it for NULL anywhere instead of the deinitialization routine because
if we can't get enough memory on startup we don't run at all.
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sl_realloc_bufs() there is no reason to check if the requested MTU greater
than or equal to the current MTU value as this function called only
when requested
MTU not equals to the current value. So, the ">=" operation can be
safely replaced
with the ">".
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This never, ever, happens.
Neighbour entries are always tied to one address family, and therefore
one set of dst_ops, and therefore one dst_ops->protocol "hh_type"
value.
This capability was blindly imported by Alexey Kuznetsov when he wrote
the neighbour layer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of all of the useless and costly indirection
by doing the neigh hash table lookup directly inside
of the neighbour binding.
Rename from arp_bind_neighbour to rt_bind_neighbour.
Use new helpers {__,}ipv4_neigh_lookup()
In rt_bind_neighbour() get rid of useless tests which
are never true in the context this function is called,
namely dev is never NULL and the dst->neighbour is
always NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
Compute drivers may change this, so make sure to emit it to
avoid errors in bo blits.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39119
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Konstantin Belousov found an error in the define of G4x_GMCH_SIZE_VT_2M
relative to the GMCH specs, and confirmed that indeed one of his users
with a Q45 reports 0xb not 0xc for a 2/2MiB GATT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Konstantin Belousov <kostikbel@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: incorporated suggestions from Randy Dunlap
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we cannot allocate new skbs in RX completion handler, we should
increase netdevice rx_dropped counter, not spam console messages.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In process and sleep allowed context, favor GFP_KERNEL allocations over
GFP_ATOMIC ones.
-v2: fixed checkpatch.pl warnings
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ben Greear <greearb@candelatech.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Jumbo Frames feature on 82583 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable GPU reset on Ivybridge.
drm/i915/dp: manage sink power state if possible
drm/i915/dp: consolidate AUX retry code
drm/i915/dp: remove DPMS mode tracking from DP
drm/i915/dp: try to read receiver capabilities 3 times when detecting
drm/i915/dp: read more receiver capability bits on hotplug
drm/i915/dp: use DP DPCD defines when looking at DPCD values
drm/i915/dp: retry link status read 3 times on failure
Almost all of these have long outstayed their welcome.
And for every one of these macros, there are 10 features for which we
didn't add macros.
Let's just delete them all, and get out of habit of doing things this
way.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Because struct rpcbind_args *map was declared static, if two
threads entered this method at the same time, the values
assigned to map could be sent two two differen tasks.
This could cause all sorts of problems, include use-after-free
and double-free of memory.
Fix this by removing the static declaration so that the map
pointer is on the stack.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
...which is measured by the size and not the amount of space remaining.
Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:
[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
