There are three types of messages between w1 core and userspace:
1. Events. They are generated each time new master or slave device found
either due to automatic or requested search.
2. Userspace commands. Includes read/write and search/alarm search comamnds.
3. Replies to userspace commands.
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Special file in each w1 slave device's directory called "rw" is created
each time new slave and no appropriate w1 family is registered.
"rw" file supports read and write operations, which allows to perform
almost any kind of operations. Each logical operation is a transaction
in nature, which can contain several (two or one) low-level operations.
Let's see how one can read EEPROM context:
1. one must write control buffer, i.e. buffer containing command byte
and two byte address. At this step bus is reset and appropriate device
is selected using either W1_SKIP_ROM or W1_MATCH_ROM command.
Then provided control buffer is being written to the wire.
2. reading. This will issue reading eeprom response.
It is possible that between 1. and 2. w1 master thread will reset bus for
searching and slave device will be even removed, but in this case 0xff will
be read, since no device was selected.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C creates some sysfs nodes in the wrong places: not as children of parent
controllers, but as their peers (!). This puts them into the right place
always, instead of just when the adapter is on the platform bus.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for two new VID codes, supporting Intel mobile Core
processors and new Conroe based platforms.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements support for the National Semiconductor LM70
temperature sensor.
The LM70 temperature sensor chip supports a single temperature sensor.
It communicates with a host processor (or microcontroller) via an
SPI/Microwire Bus interface.
Communication with the LM70 is simple: when the temperature is to be sensed,
the driver accesses the LM70 using SPI communication: 16 SCLK cycles
comprise the MOSI/MISO loop. At the end of the transfer, the 11-bit 2's
complement digital temperature (sent via the SIO line), is available in the
driver for interpretation. This driver makes use of the kernel's in-core
SPI support.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hardware monitoring chips don't have to be on the I2C bus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Merge setup function
Merge i801_setup into i801_probe, as it doesn't make much sense to
have them split. This lets us handle errors better. Christopher
Hellwig had been suggesting this back in March 2003 when the driver
was merged.
Also drop two useless debug messages (revision and base address can be
obtained from lspci, procfs or sysfs.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Better pci subsystem integration
Integrate the i2c-i801 driver better with the pci subsystem, by
calling pci_{enable,disable}_device and requesting the I/O region
by BAR rather than direct configuration space access.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Cleanups
Various cleanups to the i2c-i801 driver:
* Fix documentation file and self file name references.
* i801_setup can be marked __devinit.
* Drop useless error local variable and label in i801_setup.
* Avoid a double PCI configuration register write in some cases.
* Use symbolic names for SMBHSTCFG bits.
* Transmit the error code returned by i801_setup instead of forcing it
to an arbitrary value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Remove PCI function check
Remove the PCI function number check when probing devices.
This check is redundant, each function has a separate PCI device
ID, so checking for that ID is sufficient.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Remove force_addr parameter
Remove the force_addr module parameter. It doesn't appear to ever
have been needed, and PCI resources shouldn't be arbitrarily
changed anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Fix block transaction poll loops
Two of the three poll loops have the poll and sleep swapped,
causing an extra sleep to occur after the polled condition is
fulfilled. In practice, this doubles the amount of sleep time for
every block transaction.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In i2c bus driver scx200_acb, function scx200_acb_probe can be
tagged __init.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the CS5535 and CS5536, the I/O resource is allocated through PCI,
so use that instead of using the MSR backdoor.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch marks i2c_smbus_write_block_data() and
i2c_smbus_write_i2c_block_data() buffers as const.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup to the i2c-ocores driver.
Peter Korsgaard will maintain the i2c-ocores driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One of my testers had a problem where the driver only saw 2 of the 4 fan
sensors his uGuru has, this fixes this.
-accept 0x40 (bit 6) being high as a valid fan sensor setting for all fans
not just fan 1, I have a feeling this bit indicates whether or not a fan is
actually connected .
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes to the Abit uGuru driver as requested in review by Jean Delvare:
- exactly calculate the sysfs_names array length using macro
- use snprintf when generating names to double check that the sysfs_names
array does not overflow.
- use ARRAY_SIZE and / or defines to determine number of loops in for loops
instead of using hardcoded values.
- In abituguru_probe(), refactor the error path leaving a single call to kfree
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New hardware monitoring driver for the Abit uGuru
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing data lock in w83792d driver to avoid unexpected
data change.
Signed-off-by: Yuan Mu <ymu@winbond.com.tw>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
W83792D use pwm register low 4 bits to store PWM/DC value, bit 7
is used to store fan PWM/DC mode. The store_pwm function did not
convert the pwm input correctly, so it may change the fan mode
when new value is set.
This fix the problem. Change the "index" value of pwm*_mode
and pwm* SENSOR_ATTR to simplify code.
Signed-off-by: Yuan Mu <ymu@winbond.com.tw>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I no more wish to be listed as the maintainer for the smsc47m1 and
w83l785ts drivers. I have no test device, and people will fallback
to me as the general hardware monitoring maintainer anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a typo in the hdaps driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Robert Love <rml@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reword and complete certain parts of the hwmon sysfs-interface
documentation file. Hopefully this will make things clearer for new
driver authors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up hwmon sysfs documentation file, plus introduces
the description of DC/PWM selection for fan speed control.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch adds support for the OpenCores I2C controller IP
core (See http://www.opencores.org/projects.cgi/web/i2c/overview).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improve the Kconfig help text of the follwing i2c drivers:
* busses/i2c-pca-isa.c
* chips/pcf8574.c
* chips/pcf8591.c
These are hard to detect and building them into the kernel
results in long delays at boot.
March 2006, thread "I2C_PCA_ISA causes boot delays"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114360399415744&w=2
April 2006, thread "i2c-related 1-minute hang during bootup"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114640992330721&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following patch trims the VID value to correct number of bits
for each VRM.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improve the help text for CONFIG_HWMON to let the users know how they
pick the right hardware monitoring driver(s) for their system.
Also fix a couple typos in the related documentation file and improve
some parts a bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One more motherboard confirmed to have an LM83 temperature sensor chip.
Thanks to Steven Hardy for reporting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the w83791d sensor chip. The w83791d hardware is
somewhere between the w83781d and the w83792d and this driver code
is derived from the code that supports those chips.
Signed-off-by: Charles Spirakis <bezaur@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the list of systems supported by the hdaps driver:
* Add the "ThinkPad Z60m" entry, reported by Arkadiusz Miskiewicz.
* Add the "ThinkPad H" entry, reported by Frank Gevaerts for some
ThinkPad R52 models (1846AQG).
* Drop the "ThinkPad X41 Tablet" entry, which looks redundant to me.
And a comment update for good measure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Arkadiusz Miskiewicz <arekm@maven.pl>
Cc: Frank Gevaerts <frank@gevaerts.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the new nForce4 MCP51 (also known as nForce 410 or
430) and nForce4 MCP55 to the i2c-nforce2 driver. Some code changes
were required because the base I/O address registers have changed in
these versions. Standard BARs are now being used, while the original
nForce2 chips used non-standard ones.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Properly document on which systems the i2c-piix4 SMBus driver will
refuse to load. Hopefully this will make it clearer for users, which
were often wondering why their destop or server systems were detected
as laptops.
Closes bug #6429.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the fix_hstcfg option from the driver and related
SMBus Interrupt Select register magic because now we know what are
valid values for this register. This patch updates the documentation
and adds new IRQ mode check so we are sure not to miss any new
"unusual" value.
The PCI quirk for users of fix_hstcfg was not developed because the
chipset lacks of subsystem ID registers and DMI is stated "To be
filled". Impact to existing systems is minimal because the problem
showed up on motherboards like 10 years back. On the other hand users
of newer Serverworks and HT1000 systems won't be misleaded by the
message suggesting to try the fix_hstcfg any more.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the ST m41t81 and m41t85 i2c rtc chips
to the existing m41t00 driver.
Since there is no way to reliably determine what type of rtc chip
is in use, the chip type is passed in via platform_data. The i2c
address and square wave frequency are passed in via platform_data
as well. To accommodate the use of platform_data, a new header
file include/linux/m41t00.h has been added.
The m41t81 and m41t85 chips halt the updating of their time registers
while they are being accessed. They resume when a stop condition
exists on the i2c bus or when non-time related regs are accessed.
To make the best use of that facility and to make more efficient
use of the i2c bus, this patch replaces multiple i2c_smbus_xxx calls
with a single i2c_transfer call.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does some cleanup to the m41t00 i2c/rtc driver including:
- use BCD2BIN/BIN2BCD instead of BCD_TO_BIN/BIN_TO_BCD
- use strlcpy instead of strncpy
- some whitespace cleanup
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the ATI IXP southbridges support to i2c-piix4,
as it turned out those chips are compatible with it.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extend the sysfs interface of hardware monitoring chips, by adding
individual alarm and beep files. Contrary to the old aggregated "alarms"
and "beeps" files, individual files constitute a standard way to access
the status information, making it finally possible to implement a
chip-independant hardware monitoring chip access library (once all
drivers have been added this new interface, that is.)
If future drivers need more individual files, the interface will be
extended as needed at the same time these drivers are merged into the
kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The F71805F I/O resource structure needs not be a global variable,
as the platform core allocs its own copy of it anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver (smsc47m192) which supports voltage and temperature
measurement features of SMSC LPC47M192 and LPC47M997 chips.
Signed-off-by: Hartmut Rick <linux@rick.claranet.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add alarms support for the W83627EHF/EHG hardware monitoring chip.
This is based on an earlier patch from Rudolf Marek.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the voltage measuring support to W83627EHF. The code is based
on the patch provided by Yuan Mu from Winbond.
Signed-off-by: Yuan Mu <Ymu@winbond.com.tw>
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add LM82 temperature sensor support (similar to the LM83,
but less featureful).
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Uli Luckas
This patch removes the fake return from serial_pxa_get_mctrl.
Signed-off-by: Uli Luckas <u.luckas@road-gmbh.de>
I just can't remember why this return was there.
Being in the first column clearly indicates it was meant to be removed.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch allows the ixp2000 uengine loader that is already in the
tree to also be used on the ixp23xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
As it's slightly nontrivial to make it possible to build a single
kernel image for both the mainstone and the logicpd pxa270 card engine,
add a separate defconfig for the logicpd pxa270 card engine for now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
