Remove wrongly applied upper limit on the interrupt transfer
interval for low speed devices (not much of an error per se,
according to USB specs).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.
Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO. This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The musb_h_disable() routine can oops in some cases:
- It's not safe to read hep->hcpriv outside musb->lock,
since it gets changed on completion IRQ paths.
- The list iterators aren't safe to use in that way;
just remove the first element while !list_empty(),
so deletions on other code paths can't make trouble.
We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.
[ dbrownell@users.sourceforge.net: massively simplify
patch description; add key points as code comments ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint. That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.
Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback). Since a QH with an empty URB
list is now supposed to be freed, do that. And remove a now-useless
check from musb_advance_schedule().
[ dbrownell@users.sourceforge.net: update patch description,
and fold in a dequeue() comment patch ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The input queue should be used for TX on endpoints which
share FIFO hardware. The host TX path wasn't doing that.
Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.
[ dbrownell@users.sourceforge.net: update patch description ]
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some config registers are not avaiable in Blackfin, we have to comment them out.
v1-v2:
- remove Blackfin specific header file
- add Blackfin register version to musb_regs.h header file
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Random host-side MUSB updates, mostly relating to better diagnostics:
+ Improve diagnostics on host side:
- tx flush fifo:
* Avoid hundreds of duplicate TX FIFONOTEMPTY messages
* make "Can't flush TX fifo" a warning, and say which endpoint
- giveback:
* use correct status code
* show completion function name not just URB pointer
- Fix annoying "1 bytes" (should be "1 byte")
+ Be more consistent about failing init of unusable fifo_mode
It's not clear why that "can't flush TX fifo" message appears, though
it might relate to disconnection; I see it not infrequently
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This bug was introduced recently. Fix it before bigger
problems appear.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes co-working issue of usb serial device with usb/net devices while
oter endpoints are free and can be used.This patch implements the policy
that if endpoint resources are available then different BULK request goes
to different endpoint otherwise they are multiplexed to one reserved
endpoint as currently done.
Switch statement case is reordered in musb_giveback() to take care of
bulk request both in multiplex scenario and otherwise.
NAK limit scheme has to be added for multiplexed BULK request scenario
to avoid endpoint starvation due to usb/net devices.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes blurred capture images in dma mode. Isochronous error field in
urb and source data buffer pointer were not updated properly in dma
mode.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor musb_hdrc updates:
- so it'll build on DaVinci, given relevant platform updates;
* remove support for an un-shipped OTG prototype
* rely on gpiolib framework conversion for the I2C GPIOs
* the <asm/arch/hdrc_cnf.h> mechanism has been removed
- catch comments up to the recent removal of the per-SOC header
with the silicon configuration data;
- and remove two inappropriate "inline" declarations which
just bloat host side code.
There are still some more <asm/arch/XYZ.h> ==> <mach/XYZ.h>
changes needed in this driver, catching up to the relocation
of most of the include/asm-arm/arch-* contents.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [2.6.27]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes kernel panic while ISO IN transfer is aborted.Replaced
usb_hcd_unlink_urb_from_ep() from musb_giveback() to __musb_giveback()
to make sure urb is unlinked before giveback when __musb_giveback() is
called from musb_urb_dequeue().
Acquired musb->lock() before usb_hcd_unlink_urb_from_ep() within in
enqueue path.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes enumeration failures when a USB device attached to a LS hub is
connected to OMAP EVM via HS hub. This is fixed by correctly
programming hub address register in enqueue path.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
