This lets userspace determine what the state of the RTS line is, which
is what is needed to properly handle data flow for this device (it
raises RTS when there is data to be sent from it.)
Cc: Kees Stoop <kees.stoop@opticon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NOP transceiver is used by all the usb transceiver which are mostly
autonomous and doesn't require any programming or which are built
into the usb ip itself.NOP transceiver only allocates the memory
for struct xceiv and calls otg_set_transceiver() so function call
to otg_get_transceiver() will return a valid transceiver.
NOP transceiver device should be registered by calling
usb_nop_xceiv_register() from platform files.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some pointless messages from the FTDI serial driver;
I found these filling up syslog on one system. Also remove
a pointless "break" after a "return" in the same area.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the usb subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes use of the generic method if a serial driver provides
no implementation. This simplifies implementing suspend/resume support
in serial drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This exports a symbol for usb_serial_generic_resume, so that modules can
use it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes an unnecessary check for autoresume from the generic
resume method. The check has been obsoleted by the now delayed
increase of the usage counter which makes the error this check prevented
impossible. This change allows drivers which only use the bulk read URB
the use of the generic method even if they support autosuspend.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Hi Greg,
this is for 2.6.30. Patches to use this in drivers are under development.
Regards
Oliver
With a postfix decrement count will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this does the standard support for suspend/resume for the opticon
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements suspend and resume methods for the
option driver. With my hardware I can even suspend the system
and keep up a connection for a short time.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround of hw bug in IMX UDC.
This bug causes wrong handling of CFG_CHG interrupt.
Workaround is documented inline source code.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix small bugs and add some omptimization in IMX UDC Gadget.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS
Features still missing:
- character length other than 8 bits
- parity settings
- break control
I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.
Usage example by Tollef Fog Heen :
TEMPer USB thermometer <http://err.no/src/TEMPer.c>
Signed-off-by: Werner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: Boris Hajduk <boris@hajduk.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
priv is checked not to be NULL near the beginning of the function and not
changed subsequently, making the test redundant.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the vbus_draw() callback to inform the transceiver, if
it exists, how much current may be drawn. The decision is
taken on gadget driver side using the configuration chosen
by the host and its bMaxPower field. Some systems can use
the host's VBUS supply to augment or recharge a battery.
(There's also a default of 100 mA for unconfigured devices,
or 8 mA if they're OTG devices.)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a transceiver driver is used, no automatic udc enable
is done. The transceiver (OTG or not) should :
- take care of VBus sensing
- call usb_gadget_vbus_connect()
- call usb_gadget_vbus_disconnect()
The pullup should remain within this driver's management,
either by gpio_pullup of udc_command() fields.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On vbus_session() call, optionally activate D+ pullup
resistor and enable the udc, or deactivate D+ pullup
resistor and disable the udc.
It is intentional to not handle any VBus sense related irq.
An external transceiver driver (like gpio_vbus) should
catch VBus sense signal, and call usb_gadget_vbus_connect()
or usb_gadget_vbus_disconnect().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prepare pxa27x_udc to handle usb D+ pullup properly : it
should connect the pullup resistor and disconnect it only
if no external transceiver is handling it.
[ dbrownell@users.sourceforge.net: kerneldoc and gpio fixes ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session. Update kerneldoc to match.
[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usblp in 2.6.18 polled for status regardless if we actually needed it.
At some point I dropped it, to save the batteries if nothing else.
As it turned out, printers exist (e.g. Canon BJC-3000) that need prodding
this way or else they stop. This patch restores the old behaviour.
If you want to save battery, don't leave jobs in the print queue.
I tested this on my printers by printing and examining usbmon traces
to make sure status is being requested and printers continue to print.
Tuomas Jäntti verified the fix on BJC-3000.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1203) increases the max_sector limit for USB tape
drives. By default usb-storage sets max_sectors to 240 (i.e., 120 KB)
for all devices. But tape drives need a higher limit, since tapes can
and do have very large block sizes. Without the ability to transfer
an entire large block in a single command, such tapes can't be used.
This fixes Bugzilla #12207.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Phil Mitchell <philipm@sybase.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore some code that was wrongly dropped from the RNDIS
driver, and caused interop problems observed with OpenMoko.
The issue is with hardware which needs help conforming to part
of the USB 2.0 spec (section 8.5.3.2); some can automagically
send a ZLP in response to an unexpected IN, but not all chips
will do that. We don't need to check the packet length ourselves
the way earlier code did, since the UDC must already check it.
But we do need to tell the UDC when it must force a short packet
termination of the data stage.
(Based on a patch from Aric D. Blumer <aric at sdgsystems.com>)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "c-enter" USB to Toshiba 1.8" IDE enclosure needs special treatment
to work flawlessly. This patch is absolutely trivial, as the integrated
USB-IDE bridge is already identified to be an "unusual" device, only the
bcdDevice is different (lower) to the bcdDeviceMin already included in
the kernel.
It is a Prolific 2507 bridge.
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2507 Rev= 0.01
S: Manufacturer=Prolific Technology Inc.
S: Product=ATAPI-6 Bridge Controller
S: SerialNumber=00000272
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Thomas Bartosik <tbartdev@gmx-topmail.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Option GTM380 in Modem mode uses Product ID 0x7201. This has been tested and works
on production systems for over 6 months.
Signed-off-by: Achilleas Kotsis <akots@exponent.gr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick
have a different Product ID (0x5010); adding this ID makes them
work just fine with the option driver
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current firmware revision 5.60 still behaves the same,
so update the quirk up a (non-existing) 99.99 revision.
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=493415
Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Tested-by: Jan Heitkoetter <devnull@heitkoetter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
The generic cdc-acm driver is now the best one to handle Sony Ericsson
F3507g-based devices (which the Dell 5530 is a rebrand of), now that all
the pieces are in place (ie, cac477e8f1).
Removing the IDs from option allows cdc-acm to handle the device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1225) fixes a bug in ehci-hcd. The condition for
whether unlinked QHs can become IDLE should not be that the controller
is halted, but rather that the controller isn't running. In other
words when the root hub is suspended, the hardware doesn't own any
QHs.
This fixes a problem that can show up during hibernation: If a QH is
only partially unlinked when the root hub is frozen, then when the
root hub is thawed the QH won't be in the IDLE state. As a result it
can't be used properly for new URB submissions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Brandon Philips <brandon@ifup.org>
Tested-by: Brandon Philips <brandon@ifup.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing
isochronous URB's kref.counts incrementing once per usb_submit_urb() call.
The culprit is *usb being set to NULL when usb_put_urb() is called after URB
is given back.
Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb()
nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd.
Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a
stream finishes.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please consider this small patch for the usb option-card driver.
This patch adds the ZTE 622 usb modem device.
Signed-off-by: Albert Pauw <albert.pauw@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we don't leak locked vstdev->lock in vstusb_write. Unlock
properly on one fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is an omitted unlock in mdc800_usb_probe's fail path. Add it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Henning Zabel <henning@uni-paderborn.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do not hold mutex in one place in cxacru_cm, but unlock it on fail path.
Fix this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbfs driver manages a list of completed asynchronous URBs. But
it is too eager to free the entries on this list: destroy_async() gets
called whenever an interface is unbound or a device is removed, and it
deallocates the outstanding struct async entries for all URBs on that
interface or device. This is wrong; the user program should be able
to reap an URB any time after it has completed, regardless of whether
or not the interface is still bound or the device is still present.
This patch (as1222) moves the code for deallocating the completed list
entries from destroy_async() to usbdev_release(). The outstanding
entries won't be freed until the user program has closed the device
file, thereby eliminating any possibility that the remaining URBs
might still be reaped.
This fixes a bug in which a program can hang in the USBDEVFS_REAPURB
ioctl when the device is unplugged.
Reported-and-tested-by: Martin Poupe <martin.poupe@upek.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver already supports the 1 protocol support, so just add it to
the MODULE_DEVICE_TABLE entry so it properly picks up these devices.
Thanks to Jouni Rynö for pointing this out.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
open() will never succeed, as we always return -ENODEV. Fix this
obvious bug.
Thanks to Jouni Ryno for reporting it.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SRP sysfs attribute is dependent on gadget mode; any
gadget may support SRP. But "rmmod musb_hdrc" didn't
remove that attribute; fix.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
