Commit Graph

513 Commits

Author SHA1 Message Date
Linus Torvalds
85082fd7cb Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
  [ARM] 5171/1: ep93xx: fix compilation of modules using clocks
  [ARM] 5133/2: at91sam9g20 defconfig file
  [ARM] 5130/4: Support for the at91sam9g20
  [ARM] 5160/1: IOP3XX: gpio/gpiolib support
  [ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
  [ARM] 5084/1: zylonite: Register AC97 device
  [ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
  [ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
  [ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
  [ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
  [ARM] 5144/1: pxaficp_ir: cleanup includes
  [ARM] pxa: remove pxa_set_cken()
  [ARM] pxa: allow clk aliases
  [ARM] Feroceon: don't disable BPU on boot
  [ARM] Orion: LED support for HP mv2120
  [ARM] Orion: add RD88F5181L-FXO support
  [ARM] Orion: add RD88F5181L-GE support
  [ARM] Orion: add Netgear WNR854T support
  [ARM] s3c2410_defconfig: update for current build
  [ARM] Acer n30: Minor style and indentation fixes.
  ...
2008-07-14 16:06:58 -07:00
Russell King
f0006314d3 Merge branch 'imx' into devel
Conflicts:

	arch/arm/mm/Kconfig
2008-07-10 16:41:50 +01:00
Philipp Zabel
97f8571e66 pxamci: fix byte aligned DMA transfers
The pxa27x DMA controller defaults to 64-bit alignment. This caused
the SCR reads to fail (and, depending on card type, error out) when
card->raw_scr was not aligned on a 8-byte boundary.

For performance reasons all scatter-gather addresses passed to
pxamci_request should be aligned on 8-byte boundaries, but if
this can't be guaranteed, byte aligned DMA transfers in the
have to be enabled in the controller to get correct behaviour.

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-06 10:37:40 -07:00
Sascha Hauer
38a41fdf94 IMX: introduce clock API
This patch introduces the clock API for i.MX and converts all
in-Kernel drivers to use it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-07-05 10:02:46 +02:00
Pierre Ossman
bf5b1935d8 mmc: don't use DMA on newer ENE controllers
Even the newer ENE controllers have bugs in their DMA engine that make
it too dangerous to use. Disable it until someone has figured out under
which conditions it corrupts data.

This has caused problems at least once, and can be found as bug report
10925 in the kernel bugzilla.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04 10:44:49 -07:00
Andres Salomon
603ded16a3 olpc: sdhci: add quirk for the Marvell CaFe's interrupt timeout
The CaFe chip has a hardware bug that ends up with us getting a timeout
value that's too small, causing the following sorts of problems:

[   60.525138] mmcblk0: error -110 transferring data
[   60.531477] end_request: I/O error, dev mmcblk0, sector 1484353
[   60.533371] Buffer I/O error on device mmcblk0p2, logical block 181632
[   60.533371] lost page write due to I/O error on mmcblk0p2

Presumably this is an off-by-one error in the hardware.  Incrementing
the timeout count value that we stuff into the TIMEOUT_CONTROL register
gets us a value that works.  This bug was originally discovered by
Pierre Ossman, I believe.

[thanks to Robert Millan for proving that this was still a problem]

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04 10:40:09 -07:00
Andres Salomon
e08c1694d9 olpc: sdhci: add quirk for the Marvell CaFe's vdd/powerup issue
This has been sitting around unloved for way too long..

The Marvell CaFe chip's SD implementation chokes during card insertion
if one attempts to set the voltage and power up in the same
SDHCI_POWER_CONTROL register write.  This adds a quirk that does
that particular dance in two steps.

It also adds an entry to pci_ids.h for the CaFe chip's SD device.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04 10:40:09 -07:00
Paulius Zaleckas
f7def13ed0 [ARM] 5122/1: imx_dma_request_by_prio simpilfication
imx_dma_request_by_prio can return channel number by itself.
No need to supply variable address through parameters.

Also converted all drivers using this function.

Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-03 16:39:57 +01:00
Chuck Ebbert
cef33400d0 mmc: wbsd: initialize tasklets before requesting interrupt
With CONFIG_DEBUG_SHIRQ set we will get an interrupt as soon as we
allocate one.  Tasklets may be scheduled in the interrupt handler but they
will be initialized after the handler returns, causing a BUG() in
kernel/softirq.c when they run.

Should fix this Fedora bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=449817

Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12 18:05:41 -07:00
Ben Collins
203c80187e mmc: Fix crash in mmc_block on 64-bit
Fairly simple. "dev_use" was being allocated as a zero length array
because of bad math on 64-bit systems, causing a crash in
find_first_zero_bit(). One-liner follows:

Signed-off-by: Ben Collins <ben.collins@canonical.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 16:14:17 -07:00
Al Viro
46cb69ccdf missing dependencies on HAS_DMA
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-21 16:55:59 -07:00
Linus Torvalds
8033c6e973 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  at91_mci: minor cleanup
  mmc: mmc host test driver
  mmc: Fix omap compile by replacing dev_name with dma_dev_name
2008-05-19 16:40:30 -07:00
Marc Pignat
e5c0ef90e6 at91_mci: minor cleanup
MMC_POWER_ON is a noop, no need to set the power pin again.

Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-05-17 13:19:38 +02:00
Pierre Ossman
88ae600d58 mmc: mmc host test driver
A dummy driver that performs a series of requests that are often mis-
handled by host drivers.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-05-14 21:02:16 +02:00
Tony Lindgren
df48dd0287 mmc: Fix omap compile by replacing dev_name with dma_dev_name
This patch fixes error:

drivers/mmc/host/omap.c: In function 'mmc_omap_get_dma_channel':
drivers/mmc/host/omap.c:1038: error: called object 'dev_name' is not a function

Commit 06916639e2 adds a function
called dev_name. This will cause a name conflict as dev_dbg calls
dev_name(((host->mmc)->parent)).

This same issue should not affect other drivers as they don't seem
to use dev_name with dev_dbg.

Thanks to Paul Walmsley <paul@pwsan.com> for figuring this one out.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-05-14 21:00:53 +02:00
Harvey Harrison
55654be9e1 mmc: make one-bit signed bitfields unsigned
Otherwise it can only take the values 0/-1 which doesn't seem to
have been intended.

drivers/mmc/host/sdhci.h:190:20: error: dubious one-bit signed bitfield

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-13 08:02:23 -07:00
Linus Walleij
c8df9a53e8 [ARM] 5024/1: Fix some minor clk issues in the MMCI PL18x driver
This fixes some two minor clk issues.

The first is a comparison where a byte will probably wrap around to 0 instead of being saturated to 255, shouldn't be triggered very often but need fixing.

The second is an attempt by the driver to adjust MCLK down to the maximum frequency according to the spec, so we don't accidentally overclock the PL18x block. None of the mach-{versatile|integrator|lh7a40x} that use it in-tree seem to have a problem with this (all are well below 100MHz, typically 33MHz), but some day there will be a problem.

This is not applied on top of the earlier mmci patch for race condition but rather a clean 2.6.25, but I guess it applies without major protests anyway.

Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-05-04 11:06:05 +01:00
Linus Torvalds
d973664992 Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (26 commits)
  [ARM] pxa: fix 1c104e0e4f
  [ARM] serial: s3c2410: platform_get_irq() may return signed unnoticed
  [ARM] am79c961a: platform_get_irq() may return signed unnoticed
  [ARM] Feroceon: Feroceon-specific WA-cache compatible {copy,clear}_user_page()
  [ARM] Feroceon: fix function alignment in proc-feroceon.S
  [ARM] Orion: catch a couple more alternative spellings of PCIe
  [ARM] Orion: fix orion-ehci platform resource end addresses
  [ARM] Orion: fix ->map_irq() PCIe bus number check
  [ARM] Orion: fix ioremap() optimization
  [ARM] feroceon: remove CONFIG_CPU_CACHE_ROUND_ROBIN check
  [ARM] feroceon: remove CONFIG_CPU_DCACHE_WRITETHROUGH check
  kprobes/arm: fix decoding of arithmetic immediate instructions
  kprobes/arm: fix cache flush address for instruction stub
  [ARM] 5022/1: Race in ARM MMCI PL18x driver, V2
  [ARM] 5021/1: at91: buildfix for sam9263 + PM
  [ARM] 5018/1: RealView: Fix the ARM11MPCore Oprofile compilation
  [ARM] 5016/1: AT91: typo in mci configuration for at91cap at91sam9263
  [ARM] 5017/1: pxa3xx: Report unsupported wakeup sources in pxa3xx_set_wake()
  [ARM] 5020/1: magician: remove __devinit marker from pasic3_leds_info
  [ARM] 5014/1: Cleanup reset state before entering suspend or resetting.
  ...
2008-04-29 15:18:06 -07:00
Harvey Harrison
48b2cf9e29 mmc: use get/put_unaligned_* helpers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Jones <tonyj@suse.de>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-29 08:06:27 -07:00
Linus Walleij
26eed9a5c6 [ARM] 5022/1: Race in ARM MMCI PL18x driver, V2
Updated version of 4446/1. This also drops the suggested comparison
of host_remain for == 0, since that doesn't make sense (still works
for us, too). We have verified that this patch solve race problems
on atleast 2 archs at high frequencies.

(Verbatim copy of old patch text below.)

The patch below fixes a race condition in the ARM MMCI PL18x driver.

If new data arrives in the FIFO while existing data is being read then
we get a second iteration of the loop in mmci_pio_read.

However host->size is not updated until after mmci_pio_read returns,
so we get count = number of new bytes PLUS number of bytes already
copied in the first iteration. This results in a FIFO underrun as
we try and read mode data than is available.

The fix is to compensating for data read on previous iterations
when calculating the amount of data in the FIFO.

Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-04-28 17:03:34 +01:00
Adrian Bunk
e70aa3fac1 mmc: sdio_ops.c should #include "sdio_ops.h"
Every file should include the headers containing the externs for its
global functions.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:33 +02:00
Adrian Bunk
98b843be56 mmc: proper prototypes for mmc_attach_*()
This patch adds proper prototypes for mmc_attach_*() in
drivers/mmc/core/core.h

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:32 +02:00
Adrian Bunk
261172fd1b mmc: make __mmc_release_bus() static
This patch makes the needlessly global __mmc_release_bus() static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:32 +02:00
Pierre Ossman
0b82684c3c sdhci: improve no card, no reset quirk
The quirk was meant to just inhibit some resets, but ended up blocking
all of them. Fortunately, this was just what was needed. Change the
comment to reflect reality.

Also, this issue has just been observed on Samsung laptops, so reduce
the number of chips the quirk affects.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
9d7c6eee52 MMC: OMAP: Do not busy wait for end of command for ever
The limit was a fixed 100k limit in the busy loop, which is not
accurate. It would better to have time limit for the worst case
which occurs when sending 80 cycles at 400 kHz and takes about
200 microseconds, so limit the max time spend in the busy loop
for some 250 microseconds.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
0f602ec79a MMC: OMAP: Start new commands from work queue instead of irq
Use work queues for starting new commands instead of starting them
directly from irq handler. The command scheduling needs to be delayed
a bit for some cards which should not be done from an interrupt.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
0807a9b573 MMC: OMAP: Lazy clock shutdown
MMCA spec says the mmc clock should be kept running for at least
8 cycles after the last RW request. Ensure this with lazy clock
disable after a request, or with an explicit delay before
switching a slot.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
0fb4723d40 MMC: OMAP: Move failing command abortion to workqueue
Abort failed command from workqueue rather than from an interrupt,
allowing longer delays in abortion.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:31 +02:00
Jarkko Lavinen
7584d276d4 MMC: OMAP: Use tasklet instead of workqueue for cover switch notification
The cover waitqueue is occasionally scheduled twice from timer
and the interrupt and oops follows. It would have been possible
to fix this problem with spinlocks but using tasklet was a dropin
solution with no need for locking.

This path also adds some cleanups.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Kyungmin Park
8348f0029d MMC: OMAP: Check the get_cover_state function pointer if not set
If the get_cover_state is not set, it occurs the oops.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Carlos Eduardo Aguiar
01e77e13fc MMC: OMAP: Using setup_timer instead of init_timer
Using setup_timer() instead of init_timer() on omap.c file.

Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Jarkko Lavinen
eb1860bccd MMC: OMAP: Abort stuck commands
When a card is removed while it is being accessed, a command can get stuck so
that no timeout or end of command interrupt ever occurs. The command getting
stuck is almost always CDM12, but also the other commands can get stuck. Catch
a stuck command with a timer and try sending the initialization stream until
the controller starts running again and responds with the end of command
status.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:30 +02:00
Juha Yrjola
2a50b8889b MMC: OMAP: General cleanup for MMC multislot support
General code cleanup, modifications at some dev_* functions and
other hacks at mmc_omap_irq() for MMC multislot support.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
65b5b6e51b MMC: OMAP: Power functions modified to MMC multislot support
Modifications at power functions to MMC multislot support. This patch
also move board-specific code out of MMC OMAP driver.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
b8f9f0e90a MMC: OMAP: Fix timeout calculation for MMC multislot support
Fix the data timeout calculation for MMC multislot support.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
a914ded235 MMC: OMAP: New release dma and abort xfer functions
New functions to support MMC multislot:
mmc_omap_release_dma() and mmc_omap_abort_xfer().

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:29 +02:00
Juha Yrjola
5a0f3f1f71 MMC: OMAP: Add back cover switch support
This patch adds back MMC cover switch support in a way that
supports multiple slots.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:28 +02:00
Juha Yrjola
abfbe5f785 MMC: OMAP: Introduce new multislot structure and change driver to use it
Introduce new MMC multislot structure and change driver to use it.

Note that MMC clocking is now enabled in mmc_omap_select_slot()
and disabled in mmc_omap_release_slot().

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:28 +02:00
Tony Lindgren
4bc9e35556 MMC: OMAP: Remove cover switch handling to allow adding multislot support
This patch removes the MMC cover switch handling temporarily
to make following multislot patches cleaner.

MMC cover switch handling will be added back in later patches
after adding basic multislot support.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:28 +02:00
Francisco Alecrim
d365abe27d MMC: OMAP: Fix the BYTEBLOCK capability removal
According with commit 255d01af9a
from Linux-OMAP tree, the BYTEBLOCK capability was removed by Pierre Ossman.
MMC_CAP_BYTEBLOCK is not defined causing the compile error:

drivers/mmc/host/omap.c: In function `mmc_omap_probe':
drivers/mmc/host/omap.c:1077: error: `MMC_CAP_BYTEBLOCK' undeclared (first use in this function)
drivers/mmc/host/omap.c:1077: error: (Each undeclared identifier is reported only once
drivers/mmc/host/omap.c:1077: error: for each function it appears in.)

Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Tony Lindgren
ec2f362a91 MMC: OMAP: Remove extra divisor increase
As noted by Kyungmin Park, the divisor calculation has
an unnecessary increase.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Carlos Eduardo Aguiar
5ec21b1ccf MMC: OMAP: Remove some opcodes from host driver
This patch removes some opcodes from host driver so there's no need on putting
'#include <linux/mmc/mmc.h>', that should not be needed in host drivers.

Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Robert P. J. Day
6fee65cfde mmc: use shorter, equivalent set_current_state()
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Pierre Ossman
2f730fec83 sdhci: allow led to be controlled freely
Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Pierre Ossman
b69c905890 sdhci: remove custom controller name
Remove the use of the sdhci specific device name and use the mmc controller
name instead.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:27 +02:00
Pierre Ossman
ff3112f5ad mmc: set controller name early
Reorganise code so that mmc_hostname() works directly after allocation.
That way host drivers can use that name for resource allocations and
messages during probing.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:26 +02:00
Kay Sievers
bc65c724d5 mmc: fix platform driver hotplug/coldplug
Since 43cc71eed1, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable MMC host
platform drivers, to re-enable auto loading.

Also, add missing owner declarations in driver init.

[dbrownell@users.sourceforge.net: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-15 19:35:40 -07:00
Pierre Ossman
51ec92e295 mmc: use sysfs groups to handle conditional attributes
Suppressing uevents turned out to be a bad idea as it screws up the
order of events, making user space very confused. Change the system to
use sysfs groups instead.

This is a regression that, for some odd reason, has gone unnoticed for
some time. It confuses hal so that the block devices (which have the
mmc device as a parent) are not registered. End result being that
desktop magic when cards are inserted won't work.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-22 17:02:20 -07:00
Roel Kluin
ce63645234 tifm_sd: DATA_CARRY is not boolean in tifm_sd_transfer_data()
DATA_CARRY is not boolean

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-15 09:24:21 -07:00
Frank Seidel
882c49164d mmc: extend ricoh_mmc to support Ricoh RL5c476
This patch adds support for the Ricoh RL5c476 chip: with this
the mmc adapter that needs this disabler (R5C843) can also be
handled correctly when it sits on a RL5c476.

Signed-off-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-02-08 09:02:47 +01:00