Commit Graph

782 Commits

Author SHA1 Message Date
K.Tanaka
a07e6ab41b md: the md RAID10 resync thread could cause a md RAID10 array deadlock
This message describes another issue about md RAID10 found by testing the
2.6.24 md RAID10 using new scsi fault injection framework.

Abstract:

When a scsi error results in disabling a disk during RAID10 recovery, the
resync threads of md RAID10 could stall.

This case, the raid array has already been broken and it may not matter.  But
I think stall is not preferable.  If it occurs, even shutdown or reboot will
fail because of resource busy.

The deadlock mechanism:

The r10bio_s structure has a "remaining" member to keep track of BIOs yet to
be handled when recovering.  The "remaining" counter is incremented when
building a BIO in sync_request() and is decremented when finish a BIO in
end_sync_write().

If building a BIO fails for some reasons in sync_request(), the "remaining"
should be decremented if it has already been incremented.  I found a case
where this decrement is forgotten.  This causes a md_do_sync() deadlock
because md_do_sync() waits for md_done_sync() called by end_sync_write(), but
end_sync_write() never calls md_done_sync() because of the "remaining" counter
mismatch.

For example, this problem would be reproduced in the following case:

Personalities : [raid10]
md0 : active raid10 sdf1[4] sde1[5](F) sdd1[2] sdc1[1] sdb1[6](F)
      3919616 blocks 64K chunks 2 near-copies [4/2] [_UU_]
      [>....................]  recovery =  2.2% (45376/1959808) finish=0.7min speed=45376K/sec

This case, sdf1 is recovering, sdb1 and sde1 are disabled.
An additional error with detaching sdd will cause a deadlock.

md0 : active raid10 sdf1[4] sde1[5](F) sdd1[6](F) sdc1[1] sdb1[7](F)
      3919616 blocks 64K chunks 2 near-copies [4/1] [_U__]
      [=>...................]  recovery =  5.0% (99520/1959808) finish=5.9min speed=5237K/sec

 2739 ?        S<     0:17 [md0_raid10]
28608 ?        D<     0:00 [md0_resync]
28629 pts/1    Ss     0:00 bash
28830 pts/1    R+     0:00 ps ax
31819 ?        D<     0:00 [kjournald]

The resync thread keeps working, but actually it is deadlocked.

Patch:
By this patch, the remaining counter will be decremented if needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
1c830532f6 md: fix possible raid1/raid10 deadlock on read error during resync
Thanks to K.Tanaka and the scsi fault injection framework, here is a fix for
another possible deadlock in raid1/raid10 error handing.

If a read request returns an error while a resync is happening and a resync
request is pending, the attempt to fix the error will block until the resync
progresses, and the resync will block until the read request completes.  Thus
a deadlock.

This patch fixes the problem.

Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
Keld Simonsen
8ed3a19563 md: don't attempt read-balancing for raid10 'far' layouts
This patch changes the disk to be read for layout "far > 1" to always be the
disk with the lowest block address.

Thus the chunks to be read will always be (for a fully functioning array) from
the first band of stripes, and the raid will then work as a raid0 consisting
of the first band of stripes.

Some advantages:

The fastest part which is the outer sectors of the disks involved will be
used.  The outer blocks of a disk may be as much as 100 % faster than the
inner blocks.

Average seek time will be smaller, as seeks will always be confined to the
first part of the disks.

Mixed disks with different performance characteristics will work better, as
they will work as raid0, the sequential read rate will be number of disks
involved times the IO rate of the slowest disk.

If a disk is malfunctioning, the first disk which is working, and has the
lowest block address for the logical block will be used.

Signed-off-by: Keld Simonsen <keld@dkuug.dk>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
27c529bb8e md: lock access to rdev attributes properly
When we access attributes of an rdev (component device on an md array) through
sysfs, we really need to lock the array against concurrent changes.  We
currently do that when we change an attribute, but not when we read an
attribute.  We need to lock when reading as well else rdev->mddev could become
NULL while we are accessing it.

So add appropriate locking (mddev_lock) to rdev_attr_show.

rdev_size_store requires some extra care as well as it needs to unlock the
mddev while scanning other mddevs for overlapping regions.  We currently
assume that rdev->mddev will still be unchanged after the scan, but that
cannot be certain.  So take a copy of rdev->mddev for use at the end of the
function.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
2515619823 md: make sure a reshape is started when device switches to read-write
A resync/reshape/recovery thread will refuse to progress when the array is
marked read-only.  So whenever it mark it not read-only, it is important to
wake up thread resync thread.  There is one place we didn't do this.

The problem manifests if the start_ro module parameters is set, and a raid5
array that is in the middle of a reshape (restripe) is started.  The array
will initially be semi-read-only (meaning it acts like it is readonly until
the first write).  So the reshape will not proceed.

On the first write, the array will become read-write, but the reshape will not
be started, and there is no event which will ever restart that thread.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
d0fae18f1b md: clean up irregularity with raid autodetect
When a raid1 array is stopped, all components currently get added to the list
for auto-detection.  However we should really only add components that were
found by autodetection in the first place.  So add a flag to record that
information, and use it.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
a1801f858e md: guard against possible bad array geometry in v1 metadata
Make sure the data doesn't start before the end of the superblock when the
superblock is at the start of the device.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:17 -08:00
NeilBrown
8311c29d40 md: reduce CPU wastage on idle md array with a write-intent bitmap
On an md array with a write-intent bitmap, a thread wakes up every few seconds
and scans the bitmap looking for work to do.  If the array is idle, there will
be no work to do, but a lot of scanning is done to discover this.

So cache the fact that the bitmap is completely clean, and avoid scanning the
whole bitmap when the cache is known to be clean.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:17 -08:00
NeilBrown
a35e63efa1 md: fix deadlock in md/raid1 and md/raid10 when handling a read error
When handling a read error, we freeze the array to stop any other IO while
attempting to over-write with correct data.

This is done in the raid1d(raid10d) thread and must wait for all submitted IO
to complete (except for requests that failed and are sitting in the retry
queue - these are counted in ->nr_queue and will stay there during a freeze).

However write requests need attention from raid1d as bitmap updates might be
required.  This can cause a deadlock as raid1 is waiting for requests to
finish that themselves need attention from raid1d.

So we create a new function 'flush_pending_writes' to give that attention, and
call it in freeze_array to be sure that we aren't waiting on raid1d.

Thanks to "K.Tanaka" <k-tanaka@ce.jp.nec.com> for finding and reporting this
problem.

Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:17 -08:00
Adrian Bunk
e03f1a8422 dm-raid1.c: fix NULL dereferences
This patch fixes two NULL dereferences introduced by commit
06386bbfd2 and spotted by the Coverity
checker.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-19 15:52:27 -08:00
Jan Blunck
cf28b4863f d_path: Make d_path() use a struct path
d_path() is used on a <dentry,vfsmount> pair.  Lets use a struct path to
reflect this.

[akpm@linux-foundation.org: fix build in mm/memory.c]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-14 21:17:09 -08:00
Jan Blunck
c32c2f63a9 d_path: Make seq_path() use a struct path argument
seq_path() is always called with a dentry and a vfsmount from a struct path.
Make seq_path() take it directly as an argument.

Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-14 21:17:08 -08:00
Jan Blunck
1d957f9bf8 Introduce path_put()
* Add path_put() functions for releasing a reference to the dentry and
  vfsmount of a struct path in the right order

* Switch from path_release(nd) to path_put(&nd->path)

* Rename dput_path() to path_put_conditional()

[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-14 21:13:33 -08:00
Jan Blunck
4ac9137858 Embed a struct path into struct nameidata instead of nd->{dentry,mnt}
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.

Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
  <dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
  struct path in every place where the stack can be traversed
- it reduces the overall code size:

without patch series:
   text    data     bss     dec     hex filename
5321639  858418  715768 6895825  6938d1 vmlinux

with patch series:
   text    data     bss     dec     hex filename
5320026  858418  715768 6894212  693284 vmlinux

This patch:

Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-14 21:13:33 -08:00
Al Viro
39ed7adb17 dm-raid1 breakage on 64bit
test_and_set_bit() on address of uint32_t is a Bad Idea(tm)...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-13 08:16:34 -08:00
Jonathan Brassow
af195ac82e dm raid1: report fault status
This patch adds extra information to the mirror status output, so that
it can be determined which device(s) have failed.  For each mirror device,
a character is printed indicating the most severe error encountered.  The
characters are:
 *    A => Alive - No failures
 *    D => Dead - A write failure occurred leaving mirror out-of-sync
 *    S => Sync - A sychronization failure occurred, mirror out-of-sync
 *    R => Read - A read failure occurred, mirror data unaffected
This allows userspace to properly reconfigure the mirror set.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:39 +00:00
Jonathan Brassow
06386bbfd2 dm raid1: handle read failures
This patch gives the ability to respond-to/record device failures
that happen during read operations.  It also adds the ability to
read from mirror devices that are not the primary if they are
in-sync.

There are essentially two read paths in mirroring; the direct path
and the queued path.  When a read request is mapped, if the region
is 'in-sync' the direct path is taken; otherwise the queued path
is taken.

If the direct path is taken, we must record bio information so that
if the read fails we can retry it.  We then discover the status of
a direct read through mirror_end_io.  If the read has failed, we will
mark the device from which the read was attempted as failed (so we
don't try to read from it again), restore the bio and try again.

If the queued path is taken, we discover the results of the read
from 'read_callback'.  If the device failed, we will mark the device
as failed and attempt the read again if there is another device
where this region is known to be 'in-sync'.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:37 +00:00
Jonathan Brassow
b80aa7a0c2 dm raid1: fix EIO after log failure
This patch adds the ability to requeue write I/O to
core device-mapper when there is a log device failure.

If a write to the log produces and error, the pending writes are
put on the "failures" list.  Since the log is marked as failed,
they will stay on the failures list until a suspend happens.

Suspends come in two phases, presuspend and postsuspend.  We must
make sure that all the writes on the failures list are requeued
in the presuspend phase (a requirement of dm core).  This means
that recovery must be complete (because writes may be delayed
behind it) and the failures list must be requeued before we
return from presuspend.

The mechanisms to ensure recovery is complete (or stopped) was
already in place, but needed to be moved from postsuspend to
presuspend.  We rely on 'flush_workqueue' to ensure that the
mirror thread is complete and therefore, has requeued all writes
in the failures list.

Because we are using flush_workqueue, we must ensure that no
additional 'queue_work' calls will produce additional I/O
that we need to requeue (because once we return from
presuspend, we are unable to do anything about it).  'queue_work'
is called in response to the following functions:
- complete_resync_work = NA, recovery is stopped
- rh_dec (mirror_end_io) = NA, only calls 'queue_work' if it
                           is ready to recover the region
                           (recovery is stopped) or it needs
                           to clear the region in the log*
                           **this doesn't get called while
                           suspending**
- rh_recovery_end = NA, recovery is stopped
- rh_recovery_start = NA, recovery is stopped
- write_callback = 1) Writes w/o failures simply call
                   bio_endio -> mirror_end_io -> rh_dec
                   (see rh_dec above)
                   2) Writes with failures are put on
                   the failures list and queue_work is
                   called**
                   ** write_callbacks don't happen
                   during suspend **
- do_failures = NA, 'queue_work' not called if suspending
- add_mirror (initialization) = NA, only done on mirror creation
- queue_bio = NA, 1) delayed I/O scheduled before flush_workqueue
              is called.  2) No more I/Os are being issued.
              3) Re-attempted READs can still be handled.
              (Write completions are handled through rh_dec/
              write_callback - mention above - and do not
              use queue_bio.)

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:35 +00:00
Jonathan Brassow
8f0205b798 dm raid1: handle recovery failures
This patch adds the calls to 'fail_mirror' if an error occurs during
mirror recovery (aka resynchronization).  'fail_mirror' is responsible
for recording the type of error by mirror device and ensuring an event
gets raised for the purpose of notifying userspace.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:32 +00:00
Jonathan Brassow
72f4b31410 dm raid1: handle write failures
This patch gives mirror the ability to handle device failures
during normal write operations.

The 'write_callback' function is called when a write completes.
If all the writes failed or succeeded, we report failure or
success respectively.  If some of the writes failed, we call
fail_mirror; which increments the error count for the device, notes
the type of error encountered (DM_RAID1_WRITE_ERROR),  and
selects a new primary (if necessary).  Note that the primary
device can never change while the mirror is not in-sync (IOW,
while recovery is happening.)  This means that the scenario
where a failed write changes the primary and gives
recovery_complete a chance to misread the primary never happens.
The fact that the primary can change has necessitated the change
to the default_mirror field.  We need to protect against reading
garbage while the primary changes.  We then add the bio to a new
list in the mirror set, 'failures'.  For every bio in the 'failures'
list, we call a new function, '__bio_mark_nosync', where we mark
the region 'not-in-sync' in the log and properly set the region
state as, RH_NOSYNC.  Userspace must also be notified of the
failure.  This is done by 'raising an event' (dm_table_event()).
If fail_mirror is called in process context the event can be raised
right away.  If in interrupt context, the event is deferred to the
kmirrord thread - which raises the event if 'event_waiting' is set.

Backwards compatibility is maintained by ignoring errors if
the DM_FEATURES_HANDLE_ERRORS flag is not present.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:29 +00:00
Milan Broz
d74f81f8ad dm snapshot: combine consecutive exceptions in memory
Provided sector_t is 64 bits, reduce the in-memory footprint of the
snapshot exception table by the simple method of using unused bits of
the chunk number to combine consecutive entries.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:27 +00:00
Brian Wood
4f7f5c675f dm: stripe enhanced status return
This patch adds additional information to the status line. It is added at the
end of the returned text so it will not interfere with existing
implementations using this data. The addition of this information will allow
for a common return interface to match that returned with the dm-raid1.c
status line (with Jonathan Brassow's patches).

Here is a sample of what is returned with a mirror "status" call:
isw_eeaaabgfg_mirror: 0 488390920 mirror 2 8:16 8:32 3727/3727 1 AA 1 core

Here's what's returned with this patch for a stripe "status" call:
isw_dheeijjdej_stripe: 0 976783872 striped 2 8:16 8:32 1 AA

Signed-off-by: Brian Wood <brian.j.wood@intel.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:24 +00:00
Brian Wood
a25eb9446a dm: stripe trigger event on failure
This patch adds the stripe_end_io function to process errors that might
occur after an IO operation. As part of this there are a number of
enhancements made to record and trigger events:

- New atomic variable in struct stripe to record the number of
errors each stripe volume device has experienced (could be used
later with uevents to report back directly to userspace)

- New workqueue/work struct setup to process the trigger_event function

- New end_io function. It is here that testing for BIO error conditions
take place. It determines the exact stripe that cause the error,
records this in the new atomic variable, and calls the queue_work() function

- New trigger_event function to process failure events. This
calls dm_table_event()

Signed-off-by: Brian Wood <brian.j.wood@intel.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:22 +00:00
Jonathan Brassow
fb8b284806 dm log: auto load modules
If the log type is not recognised, attempt to load the module
'dm-log-<type>.ko'.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:19 +00:00
Milan Broz
304f3f6a58 dm: move deferred bio flushing to workqueue
Add a single-thread workqueue for each mapped device
and move flushing of the lists of pushback and deferred bios
to this new workqueue.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:17 +00:00
Milan Broz
3a7f6c990a dm crypt: use async crypto
dm-crypt: Use crypto ablkcipher interface

Move encrypt/decrypt core to async crypto call.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:14 +00:00
Milan Broz
95497a9600 dm crypt: prepare async callback fn
dm-crypt: Use crypto ablkcipher interface

Prepare callback function for async crypto operation.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:12 +00:00
Milan Broz
43d6903482 dm crypt: add completion for async
dm-crypt: Use crypto ablkcipher interface
Prepare completion for async crypto request.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:09 +00:00
Milan Broz
ddd42edfd8 dm crypt: add async request mempool
dm-crypt: Use crypto ablkcipher interface

Introduce mempool for async crypto requests.

cc->req is used mainly during synchronous operations
(to prevent allocation and deallocation of the same object).

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:07 +00:00
Milan Broz
01482b7671 dm crypt: extract scatterlist processing
dm-crypt: Use crypto ablkcipher interface

Move scatterlists to separate dm_crypt_struct and
pick out block processing from crypt_convert.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:04 +00:00
Milan Broz
899c95d36c dm crypt: tidy io ref counting
Make io reference counting more obvious.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:11:02 +00:00
Milan Broz
84131db689 dm crypt: introduce crypt_write_io_loop
Introduce crypt_write_io_loop().

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:59 +00:00
Milan Broz
dec1cedf9d dm crypt: abstract crypt_write_done
Process write request in separate function and queue
final bio through io workqueue.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:57 +00:00
Milan Broz
0c395b0f8d dm crypt: store sector mapping in dm_crypt_io
Add sector into dm_crypt_io instead of using local variable.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:54 +00:00
Alasdair G Kergon
395b167ca0 dm crypt: move queue functions
Reorder kcryptd functions for clarity.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:52 +00:00
Milan Broz
4e4eef64e2 dm crypt: adjust io processing functions
Rename functions to follow calling convention.
Prepare write io error processing function skeleton.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:49 +00:00
Milan Broz
ee7a491e62 dm crypt: tidy crypt_endio
Simplify crypt_endio function.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:46 +00:00
Milan Broz
5742fd7775 dm crypt: move error setting outside crypt_dec_pending
Move error code setting outside of crypt_dec_pending function.
Use -EIO if crypt_convert_scatterlist() fails.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:43 +00:00
Milan Broz
fcd369daa3 dm crypt: remove unnecessary crypt_context write parm
Remove write attribute from convert_context and use bio flag instead.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:41 +00:00
Milan Broz
53017030e2 dm crypt: move convert_context inside dm_crypt_io
Move convert_context inside dm_crypt_io.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:38 +00:00
Alasdair G Kergon
009cd09042 dm mpath: add missing static
A static declaration missing.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:35 +00:00
Alasdair G Kergon
0149e57fed dm: targets no longer experimental
Drop the EXPERIMENTAL tag from well-established device-mapper targets, so
the newer ones stand out better.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:32 +00:00
Milan Broz
46125c1c90 dm: refactor dm_suspend completion wait
Move completion wait to separate function

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:30 +00:00
Milan Broz
94d6351e14 dm: split dm_suspend io_lock hold into two
Change io_locking to allow processing flush in separate thread.

Because we have DMF_BLOCK_IO already set, any possible
new ios are queued in dm_requests now.

In the case of interrupting previous wait there can be more
ios queued (we unlocked io_lock for a while) but this is safe.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:27 +00:00
Milan Broz
73d410c013 dm: tidy dm_suspend
Tidy dm_suspend function

 - change return value logic in dm_suspend
 - use atomic_read only once.
 - move DMF_BLOCK_IO clearing into one place

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:25 +00:00
Milan Broz
6d6f10df89 dm: refactor deferred bio_list processing
Refactor deferred bio_list processing.

 - use separate _merge_pushback_list function
 - move deferred bio list pick up to flush function
 - use bio_list_pop instead of bio_list_get
 - simplify noflush flag use

No real functional change in this patch.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:22 +00:00
Milan Broz
6ed7ade896 dm: tidy alloc_dev labels
Tidy labels in alloc_dev to make later patches more clear.

No functional change in this patch.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:19 +00:00
Andrew Morton
a26ffd4aa9 dm ioctl: use uninitialized_var
drivers/md/dm-ioctl.c:1405: warning: 'param' may be used uninitialized in this function

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:16 +00:00
Andrew Morton
69a2ce72a4 dm: table use uninitialized_var
drivers/md/dm-table.c: In function 'dm_get_device':
drivers/md/dm-table.c:478: warning: 'dev' may be used uninitialized in this function

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:14 +00:00
Andrew Morton
e48b9db251 dm snapshot: use uninitialized_var
drivers/md/dm-exception-store.c: In function 'persistent_read_metadata':
drivers/md/dm-exception-store.c:452: warning: 'new_snapshot' may be used uninitialized in this function

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-02-08 02:10:11 +00:00