Commit Graph

559 Commits

Author SHA1 Message Date
Haavard Skinnemoen
544fc7283c [PATCH] atmel_serial: Use __raw I/O register access
Access to chip-internal registers should always be native-endian.  This is
especially important for AVR32 since it's a big-endian architecture and the
non-raw readl() and writel() macros are defined to do little-endian
accesses.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-12 09:48:29 -08:00
Matthias Fuchs
a9cccd3437 [PATCH] serial: support for new board
Add support for the CPCI-ASIO4 quad port CompactPCI UART board from
electronic system design gmbh.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11 10:51:33 -08:00
Thomas Hoehn
482120084d [PATCH] Perle multimodem card (PCI-RAS) detection
Get the Perle quad-modem PCI card (PCI-RAS4) detected by serial driver.  It
may also get the PCI-RAS8 running, but can't guarantee as I didn't had one for
testing.

Signed-off-by: Thomas Hoehn <thomas.hoehn@avocent.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11 10:51:33 -08:00
Atsushi Nemoto
138c5d258c [PATCH] serial: serial_txx9 driver update
Update the serial_txx9 driver.

 * Configurable manumum port number. (SERIAL_TXX9_NR_UARTS)
 * Remove some code which is unneeded if CONFIG_PM=n.
 * Use PCI_DEVICE() for pci device id table and make it const.
 * Do not include <asm/irq.h>

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11 10:51:27 -08:00
Jiri Slaby
b963a8441c [PATCH] Char: tty_wakeup cleanup
tty_wakeup cleanup

- remove wake_up_interruptible(&tty->write_wait) surrounding
  tty_wakup(tty);
- substitute tty->ldisc.write_wakeup(tty) + wake_up() by tty_wakeup(tty);

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11 10:51:26 -08:00
Brent Casavant
52c9ae0ac7 [PATCH] IOC3/IOC4: PCI mem space resources
The SGI IOC3 and IOC4 PCI devices implement memory space apertures, not I/O
space apertures.  Use the appropriate region management functions.

Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Stanislaw Skowronek <skylark@linux-mips.org>
Cc: Brent Casavant <bcasavan@sgi.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11 10:51:25 -08:00
Al Viro
b81831c69a [PATCH] drivers/serial NULL noise removal
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-09 09:14:06 -08:00
Paul Mackerras
8423200553 Merge branch 'linux-2.6' 2007-02-07 14:05:13 +11:00
Vitaly Bordug
5427828e83 [POWERPC] Fix kernel build errors for mpc8272ads and mpc8560ads
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:

- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
  initial commit,
- new solely-powerpc header file for 8260 family (was using one from
  arch/ppc, this one cleaned up from the extra stuff), in fact for now
  a placeholder to get the board-specific includes for stuff not yet
  capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-07 14:03:20 +11:00
Vitaly Bordug
f25222b995 [POWERPC] cpm_uart: OF-related fix for CPM1
This makes cpm uart able to work using OF-passed parameters
in case of CPM stuff (found on most mpc8xx reference and custom
boards). The idea is to keep ppc stuff working yet making it able to be
used for powerpc.

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-07 12:00:32 +11:00
Russell King
d28122a587 [ARM] Fix AMBA serial drivers for non-first serial ports
Using console=ttyAM1 or console=ttyAMA1 resulted in an oops during
boot due to trying to drive the console before that port had been
registered.  Fix this by checking whether the port is present before
allowing console setup to proceed.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-01-24 11:59:57 +00:00
Andrew Victor
9b93816690 [ARM] 4088/1: AT91: Unbalanced IRQ in serial driver suspend/resume
This patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 (and AVR32) serial driver.

It should resolve these kernel messages:
  Unbalanced IRQ x wake disable
  BUG: warning at kernel/irq/manage.c:167/set_irq_wake()

Original patch from Marc Pignat.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-01-24 11:59:55 +00:00
Andrew Victor
a14d527306 [ARM] 4086/1: AT91: Whitespace cleanup
A couple of whitespace cleanups, mainly in the AT91 header files.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-01-24 11:59:55 +00:00
Vivek Goyal
118c0ace1b [PATCH] x86-64: modpost add more symbols to whitelist pattern2
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
  and serial console support is enabled.

o Serial console setup function, serial8250_console_setup(), is a non __init
  function and it calls functions which are of type __init().
  (uart_parse_options() and uart_set_options()). Assuming, setup will
  be called during init time, changing serial8250_console_setup() to __init.

o Adding one more pattern to modpost whitelist. Console drivers might
  have *_console structures containing references to setup functions which
  can be of __init type. Don't generate warnings for those.

WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'

Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
2007-01-11 01:52:44 +01:00
Grant Likely
c98750c2eb [POWERPC] Fix mpc52xx serial driver to work for arch/ppc again
The mpc52xx_uart_of_enumerate() function was added when adding 52xx
support to arch/powerpc, but it must not be called for arch/ppc.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-01-09 17:03:02 +11:00
David S. Miller
e3a411a3df [SPARC64]: Fix of_iounmap() region release.
We need to pass in the resource otherwise we cannot
release the region properly.  We must know whether it is
an I/O or MEM resource.

Spotted by Eric Brower.

Signed-off-by: David S. Miller <davem@davemloft.net>
2006-12-31 14:06:05 -08:00
Peter Korsgaard
e21654a756 [PATCH] serial/uartlite: Only enable port if request_port succeeded
The uartlite driver used to always enable the port even if request_port
failed causing havoc. This patch fixes it.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-22 09:58:48 -08:00
Russell King
1fb8cacc19 [PATCH] Add support for Korenix 16C950-based PCI cards
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial
cards.  The JC12xx cards are standard RS232-based serial cards utilising
the Oxford 16C950 device.

The JC14xx are RS422/RS485-based cards, but in order for these to be
supported natively, we will need additional tweaks to the 8250 layers so
we can specify some values for the 950's registers.  Hence, these two
entries are commented out.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:18:11 -08:00
Linus Torvalds
775ba7ad49 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
  Fix inotify maintainers entry
  Fix typo in new debug options.
  Jon needs a new shift key.
  fs: Convert kmalloc() + memset() to kzalloc() in fs/.
  configfs.h: Remove dead macro definitions.
  kconfig: Standardize "depends" -> "depends on" in Kconfig files
  e100: replace kmalloc with kcalloc
  um: replace kmalloc+memset with kzalloc
  fix typo in net/ipv4/ip_fragment.c
  include/linux/compiler.h: reject gcc 3 < gcc 3.2
  Kconfig: fix spelling error in config KALLSYMS help text
  Remove duplicate "have to" in comment
  Fix small typo in drivers/serial/icom.c
  Use consistent casing in help message
  EXT{2,3,4}_FS: remove outdated part of the help text
2006-12-12 18:51:51 -08:00
Robert P. J. Day
bef1f40261 kconfig: Standardize "depends" -> "depends on" in Kconfig files
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-12-12 20:04:19 +01:00
Thomas Hisch
87c18aa951 Fix small typo in drivers/serial/icom.c
Signed-off-by: Thomas Hisch <t.hisch@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-12-12 19:20:35 +01:00
Paul Mundt
41504c3972 sh: SH-MobileR SH7722 CPU support.
This adds CPU support for the SH7722.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-12-12 08:42:09 +09:00
Paul Mundt
313887507f serial: sh-sci: Shut up various sci_rxd_in() gcc4 warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-12-12 08:42:08 +09:00
Don Mullis
bf4735a46a [PATCH] Kconfig refactoring for better menu nesting
Refactor Kconfig content to maximize nesting of menus by menuconfig and
xconfig.

Tested by simultaneously running `make xconfig` with and without
patch, and comparing displays.

Signed-off-by: Don Mullis <dwm@meer.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:55:39 -08:00
Alan Cox
606d099cdd [PATCH] tty: switch to ktermios
This is the grungy swap all the occurrences in the right places patch that
goes with the updates.  At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs

If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.

If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)

Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia

[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:57 -08:00
Linus Torvalds
ea14fad0d4 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
  [ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
  [ARM] 4001/1: S3C24XX: shorten reboot time
  [ARM] 3983/2: remove unused argument to __bug()
  [ARM] 4000/1: Osiris: add third serial port in
  [ARM] 3999/1: RX3715: suspend to RAM support
  [ARM] 3998/1: VR1000: LED platform devices
  [ARM] 3995/1: iop13xx: add iop13xx support
  [ARM] 3968/1: iop13xx: add iop13xx_defconfig
  [ARM] Update mach-types
  [ARM] Allow gcc to optimise arm_add_memory a little more
  [ARM] 3991/1: i.MX/MX1 high resolution time source
  [ARM] 3990/1: i.MX/MX1 more precise PLL decode
  [ARM] 3986/1: H1940: suspend to RAM support
  [ARM] 3985/1: ixp4xx clocksource cleanup
  [ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
  [ARM] 3994/1: ixp23xx: fix handling of pci master aborts
  [ARM] 3981/1: sched_clock for PXA2xx
  [ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
  [ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
  [ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
  ...
2006-12-07 15:40:39 -08:00
Lennert Buytenhek
a4ed06ad83 [PATCH] amba-pl010: clear error flags on rx error
The pl010 primecell documentation specifies that an error indicated via RSR
should be cleared by a write to ECR.  We didn't do this, which was causing
errors to be re-reported on every call to pl010_rx_chars().

Doing a write to ECR once we detect an error appears to prevent the ep93xx
console UART driver from going into a mode where it reports "ttyAM0: X
input overrun(s)" every couple of keystrokes.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:44 -08:00
Mike Galbraith
f29219f17a [PATCH] make 8250_pnp serial driver work after suspend to ram
Add suspend/resume methods to drivers/serial/8250_pnp.c.  Tested on a
P4/HT 16550A box, ttyS0 login survives across suspend to ram.

[akpm@osdl.org: cleanups]
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:43 -08:00
Maciej W. Rozycki
9399575dd3 [PATCH] dz: Fixes to make it work
This a set of fixes mostly to make the driver actually work:

1. Actually select the line for setting parameters and receiver
   disable/enable.
2. Select the line for receive and transmit interrupt handling correctly.
3. Report the transmitter empty state correctly.
4. Set the I/O type of ports correctly.
5. Perform polled transmission correctly.
6. Don't fix the console line at ttyS3.
7. Magic SysRq support.
8. Various small bits here and there.

Tested with a DECstation 2100 (thanks Flo for making this possible).

[akpm@osdl.org: fix typo]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:41 -08:00
Ralf Baechle
d3fa72e455 [PATCH] Pass struct dev pointer to dma_cache_sync()
Pass struct dev pointer to dma_cache_sync()

dma_cache_sync() is ill-designed in that it does not have a struct device
pointer argument which makes proper support for systems that consist of a
mix of coherent and non-coherent DMA devices hard.  Change dma_cache_sync
to take a struct device pointer as first argument and fix all its callers
to pass it.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:41 -08:00
Paul B Schroeder
e0980dafa3 [PATCH] Exar quad port serial
This is on our "Envoy" boxes which we have, according to the documentation, an
"Exar ST16C554/554D Quad UART with 16-byte Fifo's".  The box also has two
other "on-board" serial ports and a modem chip.

The two on-board serial UARTs were being detected along with the first two
Exar UARTs.  The last two Exar UARTs were not showing up and neither was the
modem.

This patch was the only way I could the kernel to see beyond the standard four
serial ports and get all four of the Exar UARTs to show up.

[akpm@osdl.org: build fix]
Signed-off-by:  Paul B Schroeder <pschroeder@uplogix.com>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:35 -08:00
Peter Korsgaard
238b8721a5 [PATCH] serial uartlite driver
Add a driver for the Xilinx uartlite serial controller used in boards with
the PPC405 core in the Xilinx V2P/V4 fpgas.

The hardware is very simple (baudrate/start/stopbits fixed and no break
support).  See the datasheet for details:

	http://www.xilinx.com/bvdocs/ipcenter/data_sheet/opb_uartlite.pdf

See http://thread.gmane.org/gmane.linux.serial/1237/ for the email thread.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:30 -08:00
Linus Torvalds
dd6a7c19e4 Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (43 commits)
  sh: sh775x/titan fixes for irq header changes.
  sh: update r7780rp defconfig.
  sh: compile fixes for header cleanup.
  sh: Fixup pte_mkhuge() build failure.
  sh: set KBUILD_IMAGE to something sensible.
  sh: show held locks in stack trace with lockdep.
  sh: platform_pata support for R7780RP
  sh: stacktrace/lockdep/irqflags tracing support.
  sh: Fixup movli.l/movco.l atomic ops for gcc4.
  sh: dyntick infrastructure.
  sh: Clock framework tidying.
  sh: Turn off IRQs around get_timer_offset() calls.
  sh: Get the PGD right in oops case with 64-bit PTEs.
  sh: Fix store queue bitmap end.
  sh: More flexible + SH7780 earlyprintk SCIF support.
  sh: Fixup various PAGE_SIZE == 4096 assumptions.
  sh: Fixup 4K irq stacks.
  sh: dma-api channel capability extensions.
  sh: Drop name overload in dma-sh.
  sh: Make dma-isa depend on ISA_DMA_API.
  ...
2006-12-06 08:10:55 -08:00
Greg Ungerer
a8b8d57c25 [PATCH] m68knommu: ColdFire serial driver fixes
Some updates for the old ColdFire serial driver:

 . support 3 and 4 UARTs on some ColdFire parts that have them
 . enable multifunction pins to serial for 527x CPU's
 . support the 5272 UART's fractional baud rate divisor
 . switch driver name to "mcfserial"

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-06 07:41:26 -08:00
Paul Mundt
1d118562c2 sh: Clock framework tidying.
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-12-06 10:45:40 +09:00
Paul Mundt
6fc21b82ef sh: More flexible + SH7780 earlyprintk SCIF support.
This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.

At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-12-06 10:45:39 +09:00
Yoshinori Sato
9d4436a6fb sh: Add support for SH7206 and SH7619 CPU subtypes.
This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2006-12-06 10:45:36 +09:00
Linus Torvalds
bf83c2a315 Merge master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  [PATCH] pcmcia: at91_cf update
  [PATCH] pcmcia: fix m32r_cfc.c compilation
  [PATCH] pcmcia: ds.c debug enhancements
  [PATCH] pcmcia: at91_cf update
  [PATCH] pcmcia: conf.ConfigBase and conf.Present consolidation
  [PATCH] pcmcia: remove prod_id indirection
  [PATCH] pcmcia: remove manf_id and card_id indirection
  [PATCH] pcmcia: IDs for Elan serial PCMCIA devcies
  [PATCH] pcmcia: allow for four multifunction subdevices
  [PATCH] pcmcia: handle __copy_from_user() return value in ioctl
  [PATCH] pcmcia: multifunction card handling fixes
  [PATCH] pcmcia: allow shared IRQs on pd6729 sockets
  [PATCH] pcmcia: start over after CIS override
  [PATCH] cm4000_cs: fix return value check
  [PATCH] pcmcia: yet another IDE ID
  [PATCH] pcmcia: Add an id to ide-cs.c
2006-12-05 15:52:06 -08:00
Dominik Brodowski
af2b3b503a [PATCH] pcmcia: conf.ConfigBase and conf.Present consolidation
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.

Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2006-12-04 20:12:02 -05:00
Dominik Brodowski
efd50585e2 [PATCH] pcmcia: remove manf_id and card_id indirection
As we read out the manufactor and card_id from the PCMCIA device in the
PCMCIA core, and device drivers can access those reliably in struct
pcmcia_device's fields manf_id and card_id, remove additional (and partly
broken) manf_id and card_id detection logic from PCMCIA device drivers.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2006-12-04 20:09:20 -05:00
Tony Olech
44e5e33e99 [PATCH] pcmcia: IDs for Elan serial PCMCIA devcies
Add IDs for Elan serial PCMCIA devices. In addition, move the
pdaudio_cf driver from matching based on manf_id and card_id to
the more specific prod_id1 and prod_id2 to avoid false
positives.

Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2006-12-04 20:09:19 -05:00
Grant Likely
b9272dfdfe [POWERPC] Add of_platform_bus support to mpc52xx psc uart driver
Needed to support mpc52xx boards in arch/powerpc.  This patch
retains the platform_bus support when compiling for arch/ppc,
but uses the of_platform bindings for arch/powerpc.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-05 09:53:07 +11:00
Grant Likely
9b9129e739 [POWERPC] typo fix and whitespace cleanup on mpc52xx-uart driver
Single typo fix and whitespace changes.  In preparation for heavy
changes to this driver when support for arch/powerpc is added.
Since the driver will be changing significantly anyway, then may
as well take the opportunity to clean it up first.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-05 09:53:07 +11:00
Andrew Victor
d707572695 [ARM] 3975/1: AT91: Comments in atmel_serial.h
Updated some of the comments in the atmel_serial.h header detailing
which bits are only available on the AT91RM9200 or the AT91SAM9xx
processors.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-12-04 14:37:39 +00:00
Andrew Victor
c2f5ccfbd5 [ARM] 3973/1: AT91: Serial driver compile fix
1. The CPU identification has moved from <system.h> to <cpu.h>.

2. AT91RM9200_BASE_US0 is only defined if we are compiling in support
for the AT91RM9200.  Therefore we need to replace the CONFIG_ARM ifdef
with CONFIG_ARCH_AT91RM9200

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-12-04 14:37:36 +00:00
Kalle Pokki
533462df56 [POWERPC] CPM_UART: Fix inconsistency of function definition
The below hunk was missed from the recent patch, and now, there are somewhat
inconsistent definitions:

in cpm_uart.h:
int __init cpm_uart_init_portdesc(void);

in cpm_uart_cpm1.c:
int __init cpm_uart_init_portdesc(void)
{
}

in cpm_uart_cpm2.c:
int cpm_uart_init_portdesc(void)
{
}

Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04 20:39:25 +11:00
Andrew Victor
55d8baee4a [ARM] 3954/1: AT91: Update drivers for new headers
This patch updates the drivers (and other files) which include the
hardware headers.  This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).

The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h.  Renamed it to at91_pdc.h

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-11-30 22:51:40 +00:00
Andrew Victor
79da7a610a [ARM] 3947/1: AT91: cpu_is_XXX macro's
This patch replaces the arch_identify() in system.h with a set of
cpu_is_XXX() macro's.  This allows for compile-time checking of the
target AT91 processor.

Original patch from David Brownell.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-11-30 22:51:36 +00:00
Kalle Pokki
0091cf5a6a [POWERPC] CPM_UART: Fix non-console initialisation
The cpm_uart driver is initialised incorrectly, if there is a frame buffer
console, and CONFIG_SERIAL_CPM_CONSOLE is defined. The driver fails to
call cpm_uart_init_portdesc() and set_lineif() in this case.

Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-10 21:35:36 +11:00
Kalle Pokki
599540a855 [POWERPC] CPM_UART: Fix non-console transmit
The SMC and SCC hardware transmitter is enabled at the wrong
place. Simply writing twice to the non-console port, like

$ echo asdf > /dev/ttyCPM1
$ echo asdf > /dev/ttyCPM1

puts the shell into endless uninterruptible sleep, since the
transmitter is stopped after the first write, and is not enabled
before the shutdown function of the second write. Thus the transmit
buffers are never emptied.

Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-10 21:26:40 +11:00