The mv643xx_eth driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices. The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the chip dies (probably because of a bug somewhere in the driver),
de_stop_rxtx() fails and changing the media type crashes the whole machine.
Replace BUG_ON() in de_set_media() with a warning.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Stephen Hemminger <shemminger@linux-foundation.org>
Based upon a patch by Marcel Wappler:
This patch fixes a DHCP issue of the kernel: some DHCP servers
(i.e. in the Linksys WRT54Gv5) are very strict about the contents
of the DHCPDISCOVER packet they receive from clients.
Table 5 in RFC2131 page 36 requests the fields 'ciaddr' and
'siaddr' MUST be set to '0'. These DHCP servers ignore Linux
kernel's DHCP discovery packets with these two fields set to
'255.255.255.255' (in contrast to popular DHCP clients, such as
'dhclient' or 'udhcpc'). This leads to a not booting system.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the module init message to tell that the legacy
driver loaded. This makes it less confusing, in case both drivers are loaded.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace broken code that attempted to copy 6 byte array to 64-bit
integer. Due to missing cast to 64-bit integer, left shift operation
were 32-bit and lead to bytes been copied over each other. New code
uses simple memcpy, for greater readability and efficiency.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Slightly more useful if we compare it against the sequence number of the
command we have outstanding, rather than comparing the reply with itself.
Doh. Pointed out by Sebastian Siewior
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I called p54_parse_eeprom() on a hand-coded structure
I managed to make a small mistake with wrap->len which caused
a segfault a few lines down when trying to read entry->len.
This patch changes the validation code to avoid such problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the EEPROM structure is read from hardware, it is
always little endian, annotate that in the struct and
make sure to convert where applicable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch has added pcibios_enable_device() return value check.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge rate_control_pid_shift_adjust() to rate_control_pid_adjust_rate()
in order to make the learning algorithm aware of constraints on rates. Also
add some comments and rename variables.
This fixes a bug which prevented 802.11b/g non-AP STAs from working with
802.11b only AP STAs.
This patch was originally destined for 2.6.26, and is being backported
to fix a user reported problem in post-2.6.24 kernels.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the ESP uses the AEAD interface even for algorithms which are
not combined mode, we need to select CONFIG_CRYPTO_AUTHENC as
otherwise only combined mode algorithms will work.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If all of the entropy is in the local and foreign addresses,
but xor'ing together would cancel out that entropy, the
current hash performs poorly.
Suggested by Cosmin Ratiu:
Basically, the situation is as follows: There is a client
machine and a server machine. Both create 15000 virtual
interfaces, open up a socket for each pair of interfaces and
do SIP traffic. By profiling I noticed that there is a lot of
time spent walking the established hash chains with this
particular setup.
The addresses were distributed like this: client interfaces
were 198.18.0.1/16 with increments of 1 and server interfaces
were 198.18.128.1/16 with increments of 1. As I said, there
were 15000 interfaces. Source and destination ports were 5060
for each connection. So in this case, ports don't matter for
hashing purposes, and the bits from the address pairs used
cancel each other, meaning there are no differences in the
whole lot of pairs, so they all end up in the same hash chain.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches improves the readibility of the ip6_dst_gc() routine.
It simplifies long lines which grow a lot due to the introduction
of network namespaces support.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the necessary changes to make IPv6 dst_entry garbage
collection work with multiple network namespaces.
In ip6_dst_gc(), static local variables are now declared
per-namespace.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_dst_ops is moved inside the network namespace structure. All
references to this structure are now relative to the initial network
namespace.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_dst_ops is dynamically allocated in init and exit functions. That
provides the ability to do multiple instanciations of this structure.
This will be needed for network namespaces, indeed dst_ops stores data
that are required to be per namespace: entries and gc_thresh.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rt6_info structures are moved inside the network namespace
structure. All references to these structures are now relative to the
initial network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make mindless changes and prepares the code to use dynamic
allocation for rt6_info structure. The code accesses the rt6_info
structure as a pointer instead of a global static variable.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the routing engine use the network namespaces to
access routing informations: Add a network namespace parameter to
ipv6_route_ioctl and propagate the network namespace value to all the
routing code that have not yet been changed.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a network namespace parameter to rt6_purge_dflt_routers. This is
needed to call fib6_get_table with the appropriate network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a network namespace parameter to rt6_add_route_info() and
rt6_get_route_info to enable them to handle multiple network
namespaces.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the proc entry /proc/net/rt6_stats work in all network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a network namespace parameter to rt6_lookup().
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make /proc/net/ipv6_route and /proc/net/rt6_stats to be per namespace.
These proc files are now created when the network namespace is
initialized.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a report by Andrew Morton and code analysis done
by Jarek Poplawski.
This reverts 33f807ba0d ("[NETPOLL]:
Kill NETPOLL_RX_DROP, set but never tested.") and
c7b6ea24b4 ("[NETPOLL]: Don't need
rx_flags.").
The rx_flags did get tested for zero vs. non-zero and therefore we do
need those tests and that code which sets NETPOLL_RX_DROP et al.
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop dumping of entries when af_key socket receive queue is getting
full and continue it later when there is more room again.
This fixes dumping of large databases. Currently the entries not
fitting into the receive queue are just dropped (including the
end-of-dump message) which can confuse applications.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semaphore tsock->sem is used as mutex, convert it to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rt6_stats is now per namespace with this patch. It is allocated
when a network namespace is created and freed when the network
namespace exits and references are relative to the network namespace.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allocates the rt6_stats struct dynamically when the fib6 is
initialized. That provides the ability to create several instances of
this structure for the network namespaces.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib6_rules_ops is moved to the network namespace structure. All
references are changed to have it relatively to it.
Each time a network namespace is created a new fib6_rules_ops is
allocated, initialized and stored into the network namespace
structure.
The common part of the fib rules is namespace aware, so it is quite
easy to retrieve the network namespace from the rules and use it in
the different callbacks.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib6_rules_ops structure is dynamically allocated, so that allows
to make several instances of it per network namespace.
The global static fib6_rules_ops structure is renamed to
fib6_rules_ops_template in order to quickly memcopy it for the
structure initialization.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib6_clean_node function should have the network namespace it is
working on. The fib6_cleaner_t structure is extended with the network
namespace field to be passed to the fib6_clean_node function.
The different functions calling the fib6_clean_node function are
extended with the netns parameter when needed to propagate the netns
pointer.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the timer initialization at the network namespace creation and
store the network namespace in the timer argument.
That enables multiple timers (one per network namespace) to do garbage
collecting.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_fib_timer gc timer is dynamically allocated and initialized in
the ip6 fib init function. There are no more references to a static
global variable. That will allow to make multiple instance of the
garbage collecting timer and make them per namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib tables are now relative to the network namespace. When the
garbage collector timer expires, we must have a network namespace
parameter in order to retrieve the tables. For now this is the
init_net, but we should be able to have a timer per namespace and use
the timer callback parameter to pass the network namespace from the
expired timer.
The timer callback, fib6_run_gc, is actually used to be called
synchronously by some functions and asynchronously when the timer
expires.
When the timer expires, the delay specified for fib6_run_gc parameter
is always zero. So, I changed fib6_run_gc to not be a timer callback
but a function called by the timer callback and I added a timer
callback where its work is just to retrieve from the data arg of the
timer the network namespace and call fib6_run_gc with zero expiring
time and the network namespace parameters. That makes the code cleaner
for the fib6_run_gc callers.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function fib6_clean_all takes the network namespace as
parameter. That allows to flush the routes related to a specific
network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib table for ipv6 are moved to the network namespace structure.
All references to them are made relatively to the network namespace.
All external calls to the ip6_fib functions taking the network
namespace parameter are made using the init_net variable, so the
ip6_fib engine is ready for the namespaces but the callers not yet.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the fib6 tables to be dynamically allocated. That
provides the ability to make several instances of them when a new
network namespace is created.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is changing the paths for sending MLD/MLDv2 messages
from dev_queue_xmit() to standard dst_output().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
For later use, this patch is renaming ndisc_dst_alloc()
(and related function/structures) to icmp6_dst_alloc()
(and so on). This patch also removing unused function-
pointer argument for it.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
For later use, this patch is renaming ndisc_flow_init() to
icmpv6_flow_init() and putting it in common place.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Since most users of ipv6_get_saddr() pass non-NULL as
dst argument, use ipv6_dev_get_saddr() directly.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
neigh_is_connected() is not popular at all, and the only user
drivers/net/cxgb3/l2t.c:t3_l2t_update() also have raw (expanded) expression.
Let's expand it and remove the inline function.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
