Commit Graph

117 Commits

Author SHA1 Message Date
David S. Miller
2198a10b50 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/core/dev.c
2010-10-21 08:43:05 -07:00
James Hogan
afed4ccb0d b44: fix resume, request_irq after hw reset
On resume, call request_irq() after resetting the hardware rather than
before. It's a shared interrupt so the handler could be called
immediately if another device on the same irq interrupts (and will be
called immediately if CONFIG_DEBUG_SHIRQ=y), but unless the hardware is
reinitialised with b44_init_hw() the read of the interrupt status
register will hang the system.

Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 04:25:50 -07:00
Paul Fertser
bcf64aa379 b44: fix carrier detection on bind
For carrier detection to work properly when binding the driver with a cable
unplugged, netif_carrier_off() should be called after register_netdev(),
not before.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11 15:45:35 -07:00
David S. Miller
e548833df8 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/mac80211/main.c
2010-09-09 22:27:33 -07:00
Mark Lord
32737e934a PATCH: b44 Handle RX FIFO overflow better (simplified)
This patch is a simplified version of the original patch from James Courtier-Dutton.

>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-07 13:57:23 -07:00
Eric Dumazet
bc8acf2c8c drivers/net: avoid some skb->ip_summed initializations
fresh skbs have ip_summed set to CHECKSUM_NONE (0)

We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.

Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.

Change most occurrences of :

skb->ip_summed = CHECKSUM_NONE;

by :

skb_checksum_none_assert(skb);

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02 19:06:22 -07:00
FUJITA Tomonori
3e9e0b8364 b44: remove unused dma_desc_align_mask
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-07 18:24:29 -07:00
FUJITA Tomonori
39a6f4bce6 b44: replace the ssb_dma API with the generic DMA API
Note that dma_sync_single_for_device and dma_sync_single_for_cpu support a
partial sync.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Gary Zambrano <zambrano@broadcom.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-04 16:00:42 -04:00
Eric Dumazet
1ae5dc342a net: trans_start cleanups
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-10 05:01:31 -07:00
David S. Miller
871039f02f Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/stmmac/stmmac_main.c
	drivers/net/wireless/wl12xx/wl1271_cmd.c
	drivers/net/wireless/wl12xx/wl1271_main.c
	drivers/net/wireless/wl12xx/wl1271_spi.c
	net/core/ethtool.c
	net/mac80211/scan.c
2010-04-11 14:53:53 -07:00
Jiri Pirko
22bedad3ce net: convert multicast list to list_head
Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:15 -07:00
Tejun Heo
5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Jiri Pirko
0ddf477b8a net: convert multiple drivers to use netdev_for_each_mc_addr, part3
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-22 15:45:51 -08:00
Hauke Mehrtens
53639207c0 b44: use netdev_alloc_skb instead of dev_alloc_skb
The conversion in bf0dcbd929 missed the
new allocation in b44_rx.
This patch was used in OpenWRT for a long time.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-22 15:45:48 -08:00
Hauke Mehrtens
8850dce170 b44: Set PHY address to NO_PHY if reset fails.
Do a PHY reset to test if there is an active phy and set the PHY address
to B44_PHY_ADDR_NO_PHY in case of an not active phy. This is needed for
the Linksys WRTSL54GS and Asus WL-500W.
This patch was used in OpenWRT for a long time.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-22 15:45:48 -08:00
Joe Perches
2fc96fff44 drivers/net/b44.c: Use (pr|netdev|netif)_<level> macro helpers
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove periods from formats
Coalesce long formats

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17 17:45:19 -08:00
Jochen Friedrich
f6ca057f1b b44: Ratelimit timeout error message.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17 00:03:27 -08:00
Jiri Pirko
4cd24eaf0c net: use netdev_mc_count and netdev_mc_empty when appropriate
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.

Jirka

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-12 11:38:58 -08:00
Alexey Dobriyan
a3aa18842a drivers/net/: use DEFINE_PCI_DEVICE_TABLE()
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07 23:54:26 -08:00
Stanislav Brabec
e0188829cb b44 WOL setup: one-bit-off stack corruption kernel panic fix
About 50% of shutdowns of b44 Ethernet adapter ends by kernel panic
with kernels compiled with stack-protector.

Checking b44_magic_pattern() return values, one call of
b44_magic_pattern() returns 127. It means, that set_bit(128, pmask)
was called on line 1509. It means that bit 0 of 17th byte of pmask was
overwritten. But pmask has only 16 bytes. Stack corruption happens.
 
It seems that set_bit() on line 1509 always writes one bit off.

The fix does not only solve the stack corruption, but also makes Wake
On LAN working on my onboard B44 on Asus A7V-333X mainboard.

It seems that this problem affects all kernel versions since commit
725ad800 ([PATCH] b44: add wol for old nic) on 2006-06-20.

Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-08 21:00:22 -08:00
David S. Miller
0cae200eec b44: Fix wedge when using netconsole.
Fixes kernel bugzilla #14691

Due to the way netpoll works, it is perfectly legal to see
NAPI already scheduled when new device events are pending
in b44_interrupt().

So logging a message about it is wrong and in fact harmful.

Based upon a patch by Andreas Mohr.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-30 00:13:28 -08:00
Dongdong Deng
e99b1f04d9 b44: the poll handler b44_poll must not enable IRQ unconditionally
net/core/netpoll.c::netpoll_send_skb() calls the poll handler when
it is available. As netconsole can be used from almost any context,
IRQ must not be enabled blindly in the NAPI handler of the driver
which supports netpoll.

Call trace:
netpoll_send_skb()
{
local_irq_save(flags)
  -> netpoll_poll()
    -> poll_napi()
      -> poll_one_napi()
        -> napi->poll()
            -> b44_poll()
local_irq_restore(flags)
}

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-16 20:49:47 -07:00
Michael Buesch
98a1e2a926 b44/b43/b43legacy: Fix switch warnings introduced by SSB-SDIO
This fixes some gcc warnings for switch statements.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-09 11:19:03 -04:00
David S. Miller
6cdee2f96a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/yellowfin.c
2009-09-02 00:32:56 -07:00
Stephen Hemminger
61357325f3 netdev: convert bulk of drivers to netdev_tx_t
In a couple of cases collapse some extra code like:
   int retval = NETDEV_TX_OK;
   ...
   return retval;
into
   return NETDEV_TX_OK;

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:14:07 -07:00
Dongdong Deng
22580f894a drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of spin_lock_irq() and spin_unlock_irq()
in the NETPOLL API callbacks causes the interrupts to get enabled and
can lead to kernel instability.

The solution is to use spin_lock_irqsave() and spin_unlock_restore()
to prevent the irqs from getting enabled while in netpoll_send_skb().

Call trace:
netpoll_send_skb()
{
   -> local_irq_save(flags)
     ---> dev->ndo_start_xmit(skb, dev)
         ---> spin_lock_irq()
         ---> spin_unlock_irq() *******here would enable the interrupt.
              ...
   -> local_irq_restore(flags)
}

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-14 16:41:16 -07:00
Julia Lawall
39506a552b drivers/net: Use DIV_ROUND_CLOSEST
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression x,__divisor;
@@

- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-02 12:54:18 -07:00
roel kluin
27e0955184 b44: strncpy does not null terminate string
strlcpy() will always null terminate the string. Also use the
sizeof(version) to strlcopy() the version string.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20 08:02:58 -07:00
Eric Dumazet
553e233562 net: use netdev stats in b44, sundance, via-rhine and via-velocity
Use struct net_device_stats provided in struct net_device instead of
private ones.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-27 15:47:07 -07:00
Yang Hongyang
28b7679677 dma-mapping: replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)
Replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:11 -07:00
Michael Buesch
37efa23990 b44: Use kernel DMA addresses for the kernel DMA API
We must not use the device DMA addresses for the kernel DMA API, because
device DMA addresses have an additional offset added for the SSB translation.

Use the original dma_addr_t for the sync operation.

Cc: stable@kernel.org
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-06 17:51:29 -07:00
Michael Buesch
5d4d9e8ad6 b44: Fix sizes passed to b44_sync_dma_desc_for_{device,cpu}()
> > ------------[ cut here ]------------
> > WARNING: at lib/dma-debug.c:539 check_sync+0xe9/0x341() (Not tainted)
> > Hardware name: HP Compaq nx6110 (PY501EA#AB9)
> > b44 0000:02:0e.0: DMA-API: device driver tries to sync DMA memory it has not
> > allocated [device address=0x0000000075941040] [size=1566 bytes]
> > Modules linked in: llc bnep l2cap bluetooth autofs4 lm90 hwmon i2c_i801 sunrpc
> > ipv6 cpufreq_ondemand acpi_cpufreq uinput snd_intel8x0m snd_intel8x0
> > snd_ac97_codec snd_seq_dummy ac97_bus snd_seq_oss snd_seq_midi_event snd_seq
> > snd_seq_device snd_pcm_oss snd_mixer_oss snd_pcm b44 ssb firewire_ohci
> > snd_timer ipw2200 iTCO_wdt mii firewire_core snd iTCO_vendor_support libipw
> > yenta_socket crc_itu_t lib80211 rsrc_nonstatic soundcore snd_page_alloc joydev
> > pcspkr wmi serio_raw ata_generic pata_acpi i915 drm i2c_algo_bit i2c_core video
> > output [last unloaded: scsi_wait_scan]
> > Pid: 2418, comm: S58ntpd Not tainted 2.6.29-16.fc10.i686.PAE #1
> > Call Trace:
> >  [<c04396d1>] warn_slowpath+0x7c/0xbd
> >  [<c0457fe1>] ? register_lock_class+0x17/0x290
> >  [<c0458d61>] ? mark_lock+0x1e/0x349
> >  [<c0556448>] ? _raw_spin_unlock+0x74/0x78
> >  [<c0458d61>] ? mark_lock+0x1e/0x349
> >  [<c055a060>] ? check_sync+0x37/0x341
> >  [<c055a112>] check_sync+0xe9/0x341
> >  [<c0711245>] ? _spin_unlock_irqrestore+0x45/0x55
> >  [<c04592db>] ? trace_hardirqs_on+0xb/0xd
> >  [<c055a4d1>] debug_dma_sync_single_for_device+0x2f/0x39
> >  [<f828f722>] dma_sync_single_for_device+0x4a/0x59 [b44]
> >  [<f828f76f>] ssb_dma_sync_single_for_device+0x3e/0x48 [b44]
> >  [<f8291d1e>] b44_recycle_rx+0x18c/0x196 [b44]
> >  [<f8291f9f>] b44_poll+0x277/0x3c0 [b44]
> >  [<c0687bb9>] net_rx_action+0xa1/0x1ca
> >  [<c043e30a>] __do_softirq+0x9d/0x154
> >  [<c043e413>] do_softirq+0x52/0x7e
> >  [<c043e56f>] irq_exit+0x49/0x77
> >  [<c040b22e>] do_IRQ+0x97/0xad
> >  [<c0409dac>] common_interrupt+0x2c/0x34

I don't know if this is related, but the following patch seems to fix some DMA
mapping bug. Can somebody comment who does understand the code better than me?

(completely untested)

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-04 16:48:17 -07:00
David S. Miller
aa4abc9bcc Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/iwlwifi/iwl-tx.c
	net/8021q/vlan_core.c
	net/core/dev.c
2009-03-01 21:35:16 -08:00
Michael Buesch
e92aa634a3 b44: Disable device on shutdown
Disable the SSB core on device shutdown.
This has two advantages:
1) A clean device shutdown is always desired here, because we disable
  the device's global crystal in the next statement.
2) This fixes a bug where the device will come up with the enable-bit
  set on the next initialization (without a reboot inbetween).
  This causes breakage on the second initialization due to code that
  checks this bit (ssb_device_is_enabled() checks).

Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-26 22:35:02 -08:00
Michael Buesch
f8af11af85 b44: Unconditionally enable interrupt routing on reset
Unconditionally setup the IRQ routing on chip reset.
It's safe to call ssb_pcicore_dev_irqvecs_enable() unconditionally, because
it has internal checks for redundant calls.

This fixes problems where hardware will not come up properly
due to quirks in the enable-bit hardware.

Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-26 22:33:00 -08:00
David S. Miller
9034f77bad netdev: Use __netdev_alloc_skb() instead of __dev_alloc_skb().
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-10 01:56:45 -08:00
Ben Hutchings
288379f050 net: Remove redundant NAPI functions
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:33:50 -08:00
Eric Dumazet
a58c891a53 b44: GFP_DMA skb should not escape from driver
b44 chip has some hardware limitations, that need GFP_DMA bounce
buffers in some situations.

In order to not deplete DMA zone, we should keep allocated GFP_DMA skb
only for driver use. At rx time, we copy such skb to newly allocated
skb, reusing existing copybreak infrastructure.

On machines with low amount of memory, all skb meet the hardware limitation,
so no copy is needed. We detect this situation using a new device flag, set
to one if one GFP_DMA skb was ever allocated by b44_alloc_rx_skb().

Previously allocated skb, even outside from DMA zone will then be recycled,
to have minimal impact on DMA zone use.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Ionut Leonte <ionut.leonte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-15 15:29:35 -08:00
Felix Fietkau
4ca857958c b44: fix misalignment and wasted space in rx handling
Broadcom 4400 puts a header of configurable size (apparently needs
to be at least 28 bytes) in front of received packets. When handling
this, the previous code accidentally added the offset 30 *twice* for
the software and once for the hardware, thereby cancelling out the
IP alignment effect of the 30 byte padding and wasting an additional
30 bytes of memory per packet.

This patch fixes this problem and improves routing throughput by
about 30% on MIPS, where unaligned access is expensive.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-11 00:04:12 -08:00
Stephen Hemminger
403413e50d b44: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-07 18:10:49 -08:00
David S. Miller
2d5451d261 net: Fix warning fallout from recent NAPI interface changes.
When we removed the network device argument from several
NAPI interfaces in 908a7a16b8
("net: Remove unused netdev arg from some NAPI interfaces.")
several drivers now started getting unused variable warnings.

This fixes those up.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 15:10:00 -08:00
Neil Horman
908a7a16b8 net: Remove unused netdev arg from some NAPI interfaces.
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter.  This patch cleans up that api by
properly removing it..

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-22 20:43:12 -08:00
David S. Miller
babcda74e9 drivers/net: Kill now superfluous ->last_rx stores.
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 21:11:17 -08:00
Johannes Berg
e174961ca1 net: convert print_mac to %pM
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-27 17:06:18 -07:00
Michael Buesch
f225763a7d ssb, b43, b43legacy, b44: Rewrite SSB DMA API
This is a rewrite of the DMA API for SSB devices.
This is needed, because the old (non-existing) "API" made too many bad
assumptions on the API of the host-bus (PCI).
This introduces an almost complete SSB-DMA-API that maps to the lowlevel
bus-API based on the bustype.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-27 09:09:15 -04:00
Michael Buesch
4ac58469f1 ssb: Fix usage of struct device used for DMAing
This fixes DMA on architectures where DMA is nontrivial, like PPC64.
We must use the host-device's (PCI) struct device for any DMA
operation instead of the SSB device. For this we add a new
struct device pointer to the SSB device structure that will always
point to the right device for DMAing.

Without this patch b43 and b44 drivers won't work on complex-DMA
architectures, that for example need dev->archdata for DMA operations.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-04-15 15:04:35 -04:00
Michael Buesch
5ea79631c0 b44: Truncate PHY address
Some ROMs on embedded devices store incorrect values for
the PHY address of the ethernet device.
It looks like the number is sign-extended.
Truncate the value by applying the PHY-address mask to it.
The patch was tested on a bcm47xx embedded system (where the bug
triggers) and a bcm4400 PCI card.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-25 23:42:07 -04:00
Miguel Botón
fedb0eefe2 b44: power down PHY when interface down
This is just this patch (http://lkml.org/lkml/2007/7/1/51) but adapted
to the 'b44' ssb driver.

Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:09:19 -08:00
Larry Finger
458414b2e3 b44: Convert to use of the new SPROM structure
The b44 driver is changed to use the new SPROM data structure.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:42 -08:00
Jeff Garzik
b9f2c0440d [netdrvr] Stop using legacy hooks ->self_test_count, ->get_stats_count
These have been superceded by the new ->get_sset_count() hook.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:51:45 -07:00