Switch SDIO dpc implementation from kernel thread to workqueue for
better performance and compatibility.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interrupt pending flag used in SDIO bus layer could be used in
multiple processes in different context. Use atomic_t make sure
every interrupt is handled.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove sdio bus sleep mechanism since it is never invoked.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sendpkt only called by brcmf_netdev_start_xmit now. Absorb it
to increase readability.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inside ath9k_hif_usb_firmware_fail(), the instance of
'struct struct hif_device_usb' may be freed by
ath9k_hif_usb_disconnect() after
complete(&hif_dev->fw_done);
But 'hif_dev' is still accessed after the line code
above is executed.
This patch fixes the issue by not accessing 'hif_dev'
after 'complete(&hif_dev->fw_done)' inside
ath9k_hif_usb_firmware_fail().
Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now MCI work is being queued twice by profile and status
updation. Queue MCI work once when it is needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that led pin is filled and set to OFF before starting
the driver. With recent changes, drv_start is being called even
before led_init is being completed. This is causing led is always
OFF on driver load when the interface is UP. This patch splits the
led init and fills the led pin before register hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update all coex parameters in sigle place. So that we can avoid
redoing the same operation in mutiple places and it eases debugging.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before processing BT profiles or status messages, check whether
it is requested to flush BT profile. Otherwise it might increase
number of BT profiles that affects the WLAN performance. Also
flush the profiles when MCI is recovering from broken rx. After
flushing BT profiles, query BT topology to refetch them.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the 9462 is operating in 2G mode and MCI is enabled then
reduce the selfgen chain mask to chain 1. Otherwise poor performance
was reported at short range at Rx side when COEX is enabled.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During fast channel change, perform 2g5g_switch before starting
noisefloor calibration to avoid nfload timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the driver specific SGI flag based on the station's
HT capabilities, otherwise rate control uses the wrong rate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the rtlwifi-family of drivers have been in the kernel since 3.1
or earlier. The dependence on EXPERIMENTAL can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds e-scan support (currently i-scan is in use). E-scan
is a more powerful and memory efficient method for scanning. E-scan
will be the default scan method and eventually, i-scan support will
be removed. The scan methods do not make any difference to the end-user.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes usage of some of the local data in the usb
host interface driver. This is a step in the preperation to
support multiple USB devices.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where rx buffer does not get refilled if the
packet received has an rx protocol error.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up scan related code in preparation of a new scan mechanism (e-scan)
which will follow in a separate patch.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable tx flow control for USB host interface.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware events can contain extra data. This patch adds support to
copy this data when it exists.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx flow is to be blocked due to host interface throttle then
all net if queues should be stopped.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CMD_MAC_CONTROL is currently sent async to the firmware, and is sent
from the lbs_setup_firmware() path during device init.
This means that device init can complete with commands pending, and
the if_sdio driver will sometimes power down the device (after init)
with this command still pending.
This was causing an occasional spurious command timeout after init,
leading to a device reset.
Fix this by making CMD_MAC_CONTROL synchronous when called from the
lbs_setup_firmware() path.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register macros for antenna diversity are common for
AR9462 and AR9565, rename them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds separate tx packet descriptor routine for AP
interface. This function fills bss_type, bss_num, wmm packet
delay information etc for TxPD going on AP interface.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some platforms do not support WOW. Let's change the default wakeup
criteria to 0.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will use world regulatory domain (country 00) as default
when driver is loaded. Later after a successful association
cfg80211 will change the regulatory domain to a specific country
if the AP has advertised country IE.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP's country ie is parsed and 11d information is updated in firmware
while associating. Previous mwifiex_send_domain_info_cmd_fw() call in
association path is not necessary now. Hence it is removed in this
patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"adapter->bss_prio_tbl[j].bss_prio_head" points to linked list of
interfaces with priority 'j'. "bss_prio_tbl[j].bss_prio_cur" is
supposed to point to next interface every time the routine for
dequeuing the packet is called. This ensures that each interface
gets fair chance.
Currently we have AP and station interfaces with priority '0'.
Therefore "adapter->bss_prio_tbl[0].bss_prio_cur" should
alternately point to AP and station nodes. Since "bss_prio_cur"
is not correctly updated, for each packet picked for AP, two
packets are picked for station interface.
This patch fixes the problem by correctly updating "bss_prio_cur".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AP interface has higher priority over station. Hence
separate entries are created in "adapter->bss_prio_tbl" for these
interfaces and station packet is dequeued only if there is not
packet in queue for AP. It is observed that ping for station
interface doesn't work if heavy traffic is running on AP.
The problem is fixed by having same priority for both the
interfaces. This patch also removes an extra initialisation
for "priv->bss_priority".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HostCmd_CMD_AMSDU_AGGR_CTRL is never called with GET action.
So the code in mwifiex_ret_amsdu_aggr_ctrl() becomes redundant.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HostCmd_CMD_11N_CFG is never called with GET action. So the code in
mwifiex_ret_11n_cfg() becomes redundant.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't send this command with GET action. Redundant code in
mwifiex_ret_subsc_evt() is removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever BT calibration requested, WLAN has to wait for the
calibration to be completed. But right now we defer the waiting
which might cause BT calibration to fail. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rndis_scan(), 'request' is actually always valid pointer and
the !request check is unneeded, so remove it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various parts of the code require AR9565 checks,
this patch adds them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And recognize the device in the init path.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression which was introduced in:
"mac80211: move TX station pointer and restructure TX"
IP: p54_tx_80211+0x21/0x513 [p54common]
Oops: 0000 [#1] SMP
Modules linked in: p54usb p54common [...]
Pid: 13394, comm: hostapd 3.6.0-rc4-wl+
RIP: 0010:p54_tx_80211+0x21/0x513
RSP: 0018:... EFLAGS: 00010292
[...]
Process hostapd
Stack:
[...]
Call Trace:
p54_bss_info_changed+0x204/0x21e [p54common]
ieee80211_del_station+0x16/0x32 [mac80211]
ieee80211_start_ap+0x10f/0x157 [mac80211]
nl80211_start_ap+0x315/0x361 [cfg80211]
p54_tx_80211 function is called as part of the
beacon update. The caller p54_bss_info_changed
has to supply a valid tx control struct, or
the control->sta will lead to a null pointer
dereference.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having generic hardware timer interrupt in debugfs
would come handy when we are debugging 3 WIRE
BTCOEX issues.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
