Remove the use of set_hs_extmute callback and let the codec driver to
handle the extmute GPIO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The external mute (if it is in use) is handled by a GPIO line. Prepare to
remove the set_hs_extmute callback and replace it with:
hs_extmute_gpio: the GPIO number to use for external mute
When the users of set_hs_extmute has been converted the callback can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Original author: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the omap-pcm to use dmaengine.
Certain features are not supported by after dmaengine conversion:
1. No period wakeup mode
DMA engine has no way to communicate this information through
standard channels.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the dma_data for the stream (snd_soc_dai_set_dma_data) at dai_startup
time so omap-pcm will have access to the needed information regarding to
the DMA channel earlier.
This is needed for the clean dmaengine support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of the OMAP DMA data type definition the data_type will be used to
specify the number of bits the DMA word should be configured or 0 in case
when based on the stream's format the omap-pcm can decide the needed DMA
word size.
This feature is needed for the omap-hdmi where the sDMA need to be
configured for 32bit word type regardless of the audio format used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
omap-pcm can figure out the correct dma_type based on the stream's format.
In this way we can get rid of the plat/dma.h include from these drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get the needed resources in a correct way and avoid using defines for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Based on the format of the stream the omap-pcm can decide alone what data
type should be used with by the sDMA.
Keep the possibility for OMAP dai drivers to tell omap-pcm if they want to
use different data type. This is needed for the omap-hdmi for example which
needs 32bit data type even if the stream format is S16_LE.
The check if (dma_data->data_type) is safe at the moment since omap-pcm
does not support 8bit samples (OMAP_DMA_DATA_TYPE_S8 == 0x00).
The next step is to redefine the meaning of dma_data->data_type to unblock
this limitation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The omap-pcm platform driver no longer needs this parameter to select
between ELEMENT and PACKET mode. The selection is based on the configured
packet_size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we only have element or packet synchronization we can use the
dma_data->packet_size to select the desired mode:
if packet_size is 0 we use ELEMENT mode
if packet_size is not 0 we use PACKET mode for sDMA synchronization.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When McBSP is configured in threshold mode we can use sDMA packet mode in
all cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mpc5200-psc-ac97 driver does not enumerate attached ac97 devices, so
register the device here.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert pcm030-audio-fabric to use the new snd_soc_register_card api
instead of the older method of registering a separate platform device.
Create the dai_link to the mpc5200_psc_ac97 platform using the device tree.
Convert the pcm030-audio-fabric driver to a platform-driver and add a
remove function.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mpc52xx socs do not define FSL_SOC but need SND_POWERPC_SOC defined to build
ASoC drivers.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DAPM mapping for stream events and give unique names for the streams.
This change also fixes the following warning:
twl6040-codec twl6040-codec: Failed to create Capture debugfs file
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DAPM mapping for stream events and give unique names for the streams.
This change also fixes the following warning:
twl4030-codec twl4030-codec: Failed to create Capture debugfs file
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'dres' field (discharge resistance for headphone outputs) is no longer
used in the driver, so remove it.
It was used in the original version of the driver when entering standby
from off, but we stopped using it when we switched from having a single
startup sequence to having separate cap and capless sequences.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=TZVo
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains mostly scripted changes to make omap
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
* tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_core_44xx.h local
ARM: OMAP2+: Make ctrl_module_core_44xx.h local
ARM: OMAP2+: Make board-rx51.h local
...
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
This is only used by omap1.
And to fix things properly, this should not be included
from the drivers at all.
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Includes removal of duplicate debug print affirming entry into
the probe function, an unnecessary line break of a coding line
<80 chars and a white space change (unintentional tab).
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We continue to allow the AB8500 CODEC to be registered via the AB8500
Multi Functional Device API, only this time we extract its configuration
from the Device Tree binary.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Register both parts of the MSP driver from Device Tree so that they
are probed when Device Tree is enabled. Also, as there is platform
data involved, we ensure that there is allocated memory to place the
configuration into and that the correct information is extracted from
the DT binary.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we ensure that the MOP500 audio driver will be probed during a
Device Tree boot. We also parse the sound node to link together the
codec, dma and the CPU-side Digital Audio Interface.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the initial submission of the MSP driver msp1 and msp3's associated
pinctrl mechanism was passed back to platform code using a plat_init()
call-back routine, but it has no place in platform code. The MSP driver
should set this up for the appropriate ports. Instead we use a use_pinctrl
identifier which is passed from platform_data/Device Tree which indicates
which ports should use pinctrl.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the orion include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
This is more idiomatic as it means we verify that the device is there
prior to trying to do the card probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the LRCLK is shared and the WM8960 is clock master then we should
enable the LRCM bit to tell the device that it should drive LRCLK when
either ADC or DAC is enabled rather than separately driving the two
LRCLKs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove unreferenced header files.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add missing dai_driver information to avoid these runtime errors
[ 16.433788] asoc: error - multiple DAI f0002c00.i2s registered with no name
[ 16.453551] Failed to register DAI
[ 16.461222] mpc5200-psc-i2s: probe of f0002c00.i2s failed with error -22
[ 16.475242] asoc: error - multiple DAI f0002000.ac97 registered with no name
[ 16.488087] mpc5200-psc-ac97 f0002000.ac97: Failed to register DAI
[ 16.502222] mpc5200-psc-ac97: probe of f0002000.ac97 failed with error -22
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mpc5200_psc_ac97 and mpc5200_psc_i2s modules rely on shared platform data
with mpc5200_dma.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When audmux_read_file is called, it means the driver is already
initialised successfully, so we don't need to check audmux_base.
It also fix smatch warning:
sound/soc/fsl/imx-audmux.c:78 audmux_read_file() warn: possible memory leak of 'buf'
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_imx_open should return error code returned by snd_dmaengine_pcm_open.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For ENUM controls the bitmask is calculated based on the number of items.
Currently this is done each time the control is accessed. And while the
performance impact of this should be negligible we can easily do better. The
roundup_pow_of_two macro performs the same calculation which is currently done
manually, but it is also possible to use this macro with compile time constants
and so it can be used to initialize static data. So we can use it to initialize
the mask field of a ENUM control during its declaration.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PowerPC ASoC drivers frequently use the _BE variants of the SNDRV_PCM_FORMAT
macros, so we need to look for those as well.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove a call to dma_unmap_single() from the PowerPC ASoC DMA driver. The
buffer is allocated and not actually mapped, so the unmap call doesn't
make sense. It was probably left over from some early version of the driver.
This bug was unnoticed for so long because the DMA mapping functions normally
don't do anything on PowerPC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of platform_device_alloc("soc-audio")
to register the sound card from the machine drivers. The use of
platform_device_alloc is deprecated.
Although several other drivers still use platform_device_alloc(), the
Freescale drivers were not using it to pass driver data. Instead of fixing
the driver data usage, it's better to replace the deprecated code.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the support code which uses the legacy APB DMA driver
for accessing the I2S FIFO.
The driver will use the dmaengine based APB DMA driver for
accessing reqding/writing to I2S FIFO.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than including mach/iomux-mx27.h to define gpio numbers and set
up the pins, the patch moves all these into machine code and has the
gpio numbers passed to driver via platform_data. As the result, we
can remove the mach/iomux-mx27.h inclusion from driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A bigger set of updates than I'm entirely comfortable with - things
backed up a bit due to travel. As ever the majority of these are small,
focused updates for specific drivers though there are a couple of core
changes. There's been good exposure in -next.
The AT91 patch fixes a build break.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=o1sd
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for 3.6
A bigger set of updates than I'm entirely comfortable with - things
backed up a bit due to travel. As ever the majority of these are small,
focused updates for specific drivers though there are a couple of core
changes. There's been good exposure in -next.
The AT91 patch fixes a build break.
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the pxa include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-By: Stefan Schmidt <stefan@openezx.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Harald Welte <laforge@openezx.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Tomas Cech <sleep_walker@suse.cz>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: openezx-devel@lists.openezx.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the ep93xx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Axel Lin <axel.lin@gmail.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core has for a long time had support for marking the register maps of
devices dirty when suspending so that they are resynced on resume. Also
implement this feature for CODECs using regmap.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is better style as we acquire resources we will need before we go into
the ASoC card probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Better style as we get all the resources we need prior to starting the
ASoC level probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 98d3088e5 (SoC: core: Fix check before defaulting to regmap)
, it is not necessary to provide codec->control_data anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 98d3088e5 (SoC: core: Fix check before defaulting to regmap)
, it is not necessary to provide codec->control_data anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 98d3088e5 (SoC: core: Fix check before defaulting to regmap)
, it is not necessary to provide codec->control_data anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
cpu_dai is not in use in this function and just generates warning at
compile time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is better style since it has us obtaining all resources before we
try the ASoC probe. This change also fixes a potential issue where we
don't enable the regulators before trying to confirm the device ID which
could cause a failure during probe in some system configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Timur Tabi <timur@freescale.com>
The core_intercon is added two times, remove the redundant one
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
struct fsi_master *master became member of struct fsi_priv from
71f6e0645b
(ASoC: sh_fsi: avoid using global variable)
So, master = NULL is not necessary on fsi_probe() now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pm_runtime_disable() error handling timing on fsi_probe() was wrong.
This patch fixes it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Long term all drivers should be using regmap directly. This is more
idiomatic and moves us towards the removal of the ASoC level cache
code.
The initialiasation of reserved register bits in probe() is slightly odd
as the defaults being written don't appear to match the silicon defaults
but the new code should have the same effect as the old code.
The watchdog code will now unconditionally do a mute and unmute when
resyncing but since we only sync when we are very sure there is something
to sync this should have no impact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
This is better style as it ensures we don't try to do the ASoC probe
without required resources. Also convert to devm_ while we're at it,
saving a bit of code, and fix a leak of enable on error.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
Ensure that we have confirmed that we've got the device in place before
we register with ASoC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is better style since we acquire all needed resources before we try
to do the ASoC card probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will be used to enable additional control of the regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The I2S controllers are programmed with an "attention" level of 4 DWORDs.
This must match the configuration passed to the DMA driver, so that when
they burst in data, they don't overflow the available FIFO space. Also,
the burst size is relevant to the destination for playback, and source
for capture, not vice-versa as originally written.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The pause and resume operations indicate that the stream can be
un-paused/resumed from the exact location they were paused/suspended.
This is not true for this driver, the pause and suspend triggers share
the same code path with stop, they flush all pending DMA transfers.
This drops all pending samples. The pause_release/resume triggers are
the same as start, except that prepare won't be called beforehand,
nothing will be enqueued to the DMA engine and nothing will happen (no
audio). Removing the pause flag will let apps know that it isn't
supported. Removing the resume flag will cause user space to call
prepare and start instead of resume, so audio will continue playing when
the system wakes up.
Before removing the pause and resume flags, I tested this on an exynos
5250, using 'aplay -i'. Pause/un-pause leads to silence followed by a
write error. Suspend/resume testing led to the same result. Removing
the two flags fixes suspend/resume (since snd_pcm_prepare is called
again). And leads to a proper reporting of pause not supported.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
This uses already defined name of registers and makes code more readable.
Signed-off-by: Gaëtan Carlier <gcembed@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Revert 0865a75(ASoC: imx-ssi: Remove mono support).
The bug this patch is meant to solve doesn't occur in Visstrim_M10 boards.
Furthermore, after applying this patch sound in Visstrim_M10 is played
at slower rates.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since bypass paths aren't part of DAPM streams and we may not have any
DAPM streams there may not be anything that triggers a DAPM sync for
them. Mark all input and output widgets as dirty and then sync to do so
at the end of suspend and resume.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The OMAP2+ variant of McASP is different from Davinci variant w.r.to
some register offset.
Changes
- Add new MCASP_VERSION_3 to identify new variant. New DT compatible
"ti,omap2-mcasp-audio" to identify version 3 controller.
- The register offsets are handled depending on the version.
Note:
DMA parameters (dma fifo offset) are not updated and will be done later.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Playing a mono track on a mc13783 codec results in incorrect playback rate.
Remove mono support so that a mono track can be played correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Gaëtan Carlier <gcembed@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the Tegra+WM8903 ASoC platform data header out of
arch/arm/mach-tegra, as a pre-requisite of single zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix warning by using format specifier %zu for type size_t
Sparse warning:
sound/soc/codecs/wm0010.c:411:2: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're holding the wm0010->lock mutex when we goto err_core.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Part of commit (which patches sound/soc/omap/mcbsp.c file):
8fef626 ARM/ASoC: omap-mcbsp: Remove CLKR/FSR mux configuration code
since the tree where it has been applied did not had the earlier patch:
d0db84e ASoC: omap-mcbsp: Fix 6pin mux configuration
which changed code around omap_mcbsp_6pin_src_mux().
Because of the missing part from 8fef626 the sound/soc/omap/mcbsp.c does
not compile in linux-next.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix typo caused by recent commit (cf53756 - ASoC: davinci: davinci-pcm
does not need to be a plaform_driver)
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The if condition
if (!buf && !buf->area)
checks if the buf pointer is NULL and then dereferences it again to
check if the buffer area is NULL, resulting in possible NULL
dereference.
Signed-off-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is to rename the directory "ep93xx" in "cirrus".
Name more accurately reflects the manufacturer and allows to add
drivers not only for architecture ep93xx in this directory.
Patch not contain any functional changes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All SAMSUNG ASoC needs SND_SOC_SAMSUNG configuration.
This patch change Kconfig to support all SAMSUNG ASoC.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both the schematics and practical testing show that the HP detect GPIO
is high when the headphones are plugged in. Hence, the snd_soc_jack_gpio
should not specify to invert the signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Add device tree probe for McASP driver.
Note:
DMA parameters are not populated from DT and will be done later.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Davinci McASP header & driver are shared by few OMAP platforms (like
TI81xx, AM335x). Splitting asp header into Davinci platform specific
header and Audio specific header helps to share them across platforms.
Audio specific defines is moved to to common
<linux/platform_data/davinci_asp.h> so that the header can be
accessed by all related platforms.
While here, correct the header usage (remove multiple header
re-definitions and unused headers) and remove platform names from
structures comments and enum. Also some some coding style errors.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Same as the commit 518de86 (ASoC: tegra: register 'platform' from DAIs,
get rid of pdev). It makes davinci-pcm not a platform_driver but helper
to register "platform", so that the platform_device for davinci-pcm can
be saved completely.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device tree support for tlv320aic3x CODEC driver.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we always need to have set and get callbacks for McBSP sidetone it
makes sense to combine the two macro to create the two callbacks.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To remove duplicated code from the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When asked to add the ST controls warn only if the st_data is missing.
In this way we do not block the otherwise functional card to probe.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In ddevice tree booted kernel all device have unique name and their device
id is set to 0.
Use the mcbsp->id for checking to decide which control set we should add
for McBSP sidetone handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more idimatic for modern drivers. Also fix a couple of return
codes while we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Doesn't make any practical difference given that _SUSPEND and _OFF are
equivalent for the driver but it's what we're really doing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make it easier to integrate the management of the clock supplying the
WM0010 with DAPM by providing a dummy supply widget which supplies the
interface widgets, this can be connected to clock outputs by the machines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With appropriate clocking configuration the WM0010 driver supports 44.1kHz
audio; enable that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Speyside platform by default has a WM0010 fitted. Now that we have
a public driver hook it up in the machine integration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 412312 (ASoC: dapm: Make sure all dapm contexts are updated) means
that any DAPM context being updated will have the bias level automatically
set, including the card. We can't safely do this as the card callbacks are
called for each device context and so the management of the card bias is
more complex. Several multi-component cards rely on this behaviour.
Skip updates during the asynchronous run entirely. We should really do them
in the synchronous section but it's not 100% clear which values to pick as
the different DAPM contexts may have different bias levels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 412312 (ASoC: dapm: Make sure all dapm contexts are updated)
ensures that we update non-CODEC DAPM contexts but means that if a
CODEC has no set_bias_level() operation it'll not be updated. Fix
that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM0010 is a compact digital signal processor that has been
highly optimised for low-power audio applications. Extensive memory
resources and core optimisation allow the device to manage all audio
processing algorithms efficiently and autonomously, while the host
processor sleeps or performs other tasks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are some new WM1811 variants distinguished by both revision and
cust_id which need slightly different handling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device tree support for McBSP modules on OMAP2+ SoC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can use the has_ccr flag to replace the cpu_is_omap* checks.
This provides future proof implementation and we do not need to update the
code if new OMAP revision starts to use the McBSP driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
NUM_LINKS is no longer in use by the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the feature to configure the CLKR/FSR mux on McBSP port with 6pin
configuration.
When moving to devicetree these callback can no longer be used in a clean
way anymore.
If a board require to change the 6pin port to work in 4pin setup it needs
to set up the mux in the board file.
For OMAP2/3:
u32 devconf0;
/* McBSP1 CLKR/FSR signal to be connected to CLKX/FSX pin */
devconf0 = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
devconf0 |= OMAP2_MCBSP1_CLKR_MASK | OMAP2_MCBSP1_FSR_MASK;
omap_ctrl_writel(devconf0, OMAP2_CONTROL_DEVCONF0);
For OMAP4:
u32 mcbsp_pad;
/* McBSP4 CLKR/FSR signal to be connected to CLKX/FSX pin */
mcbsp_pad = omap4_ctrl_pad_readl(OMAP2_CONTROL_DEVCONF0);
mcbsp_pad |= ((1 << 31) | (1 << 30));
omap4_ctrl_pad_writel(mcbsp_pad, OMAP2_CONTROL_DEVCONF0);
In case when the kernel is booted with DT blob the pinctrl-single will be
provided as soon as it is enabled on the platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The muxing is done at board level, no need to do it in the ASoC machine
driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the McBSP CLKS re-parenting code to ASoC driver from
arch/arm/mach-omap2.
The call fort the re-parenting has been already limited to OMAP2+ SoC in
the ASoC driver. There is no longer need to have callback function for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
