This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maple firmware does not need PCI resource allocation, and in fact, it
can cause problems in some strange cases.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do disable, not enable, the HT APIC IRQ in the function that is
supposed to.
Enable the MPIC IRQ before enabling the downstream APIC IRQ, avoids
potentially losing an interrupt.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update defconfigs for g5, pseries and generic ppc64. Default choices
for everything, with the following exceptions:
* Enable WINDFARM_PM112 on g5 and ppc64.
* Increase CONFIG_NR_CPUS to 4 in g5_defconfig
* CONFIG_TIGON3=y instead of =m in g5_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
HMT support is currently broken and needs to be reworked to play nicely
with the SMT scheduler. Remove the bit rotten bits for the time being.
I also updated an incorrect comment, we enter __secondary_hold with the
physical cpu id in r3.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
native_hpte_clear has a spinlock recursion problem with the native_tlbie_lock
being called twice, once in native_hpte_clear() and once within tlbie().
Fix the problem by changing the call to tlbie() in native_hpte_clear() to
__tlbie(). It still supports only 4k pages for now.
Signed-off-by: R Sharada <sharada@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Disable OProfile in Kconfig for iSeries to prevent hangs. OProfile
was not originally intended to work with legacy iSeries.
Signed-off-by: Kelly Daly <kelly@au.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
altivec_unavailable_exception is called without setting r3... it looks like
the r3 that actually gets passed in as struct pt_regs *regs is the
undisturbed value of r3 at the time the altivec instruction was encountered.
The user actually gets to choose the pt_regs printed in the Oops!
This fixes the oops by passing the correct pt_regs pointer to
altivec_unavailable_exception.
Signed-off-by: Alan Curry <pacman@TheWorld.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The panic CPU is waiting forever due to some large timeout value if some
CPU is not responding to an IPI.
This patch fixes the problem - the maximum waiting period will be
10 seconds and then the kdump boot will go ahead.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For kexec we need to know the size of the MMU hash table.
Currently we calculate the size once in the htab code, and then twice more in
the kexec code, once using htab_hash_mask and once using ppc64_pft_size.
On some machines the ppc64_pft_size calculation is broken because
ppc64_pft_size is not set.
So we need to fix the second calculation, but better still we should just
calculate the size once and use it everywhere else.
Tested on Power5 LPAR, Power4 non-LPAR and Power3.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When I changed the hvlpevent_queue code to use a spinlock instead of a
custom atomic (719d1cd867) I didn't
initialise the lock anywhere, oops.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some recent PowerBook models tend to lose the ethernet PHY on
suspend/resume. It -seems- that they use a combo ethernet-firewire PHY
chip and the firewire PHY seems to die the same way when that happens. Not
trying to toggle the firewire cable power appears to fix it. So this patch
disables changes to the firewire cable power control GPIO on those models.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the logical and physical cpu ids of a secondary thread don't match, we will
fail to spin the thread up on pSeries machines due to a bug in pseries/smp.c
We call the RTAS "start-cpu" method with the physical cpu id, the address of
pSeries_secondary_smp_init and the value to pass that function in r3. Currently
we pass "lcpu", the logical cpu id, but pSeries_secondary_smp_init expects
the physical cpu id in r3.
We should be passing pcpu instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For UP to SMP kexec to work we need to jump into pSeries_secondary_smp_init
event on a UP + KEXEC kernel. The secondary cpus will not find their hw_cpu_id
in the paca and so they'll jump into kexec_wait, ready for a kexec.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because smp_release_cpus() is built for SMP || KEXEC, it's not safe to
unconditionally call it from setup_system(). On a UP && KEXEC kernel we'll
start up the secondary CPUs which will then go beserk and we die.
Simple fix is to conditionally call smp_release_cpus() in setup_system(). With
that in place we don't need the dummy definition of smp_release_cpus() because
all call sites are #ifdef'ed either SMP or KEXEC.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fallback gracefully when reading /proc/ppc64/lparcfg when the /rtas
device node can't be found.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few symbols are exported twice, remove them from ppc_ksyms.c
Remove users of sys_ctrler in arch/ppc/
WARNING: vmlinux: duplicate symbol '__delay' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__up' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down_interruptible' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'sys_ctrler' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncat' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncmp' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strrchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strnlen' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strpbrk' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'memscan' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strstr' previous definition was in vmlinux
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a regression which was introduced by moving ppc32 to use
the same sort of lockless gettimeofday as ppc64 has been using for
some time. This involves getting the timebase and performing some
simple arithmetic to convert it to seconds and microseconds. However,
the factor and offset used there weren't being updated when NTP
varied the tick length using adjtimex. 64-bit didn't notice the
problem because it had a hook in the 32-bit adjtimex compat routine
that attempted to work out what the generic timekeeping code would
do and alter the factor and offset to match. However, that code
was very complex and it wasn't clear that it still matched what the
generic code would do.
Now we use the generic current_tick_length() routine that was recently
added to check that the current tick will be as long as we expect; if
not we recompute the factor and offset. This keeps gettimeofday and
xtime in sync. In addition we check that gettimeofday hasn't got ahead
of xtime on each timer interrupt; if it has, we resync.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We are setting up sources for building external modules like this:
/usr/src/linux-obj> # create a .config file
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD oldconfig
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD prepare
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD scripts
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD clean
After that, external modules can be built with:
/usr/src/module> make -C /usr/src/linux-obj M=$PWD
This fails for ppc32 because the `make clean' removes the
arch/powerpc/include directory. This should be done in archmrproper
instead of in archclean.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Embedded boards that u-boot require a kernel image in the uImage format.
This allows a given board to specify it wants a uImage built by default.
This also fixes a warning at config time, as this symbol is referred
to in arch/powerpc/platforms/83xx/Kconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With this patch 'make vmlinux.bin' works. This is needed by
some embedded platforms. Kumar already added the routines
to actually build the image in arch/powerpc/boot/Makefile.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we have some stuff in firmware.h and kernel/firmware.c that is
#ifdef CONFIG_PPC_PSERIES. Move it all into platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up fw_feature_init in platforms/pseries/setup.c. Clean up white space
and replace the while loop with a for loop - which seems clearer to me.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The e500 core reference manual indicates that isync is required
after mtmsr(DE bit) and mtspr DBCR0. Add isyncs to make the code
conform to the spec.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Ran arch/powerpc/platforms/85xx through Lindent
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename mpc85xx.c to misc.c to match the pattern established by the
8349 port - consistency is a good thing. Also run Lindent on the
file to clean it up.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cut-and-paste from the old platform code in arch/ppc resulted in
arch/powerpc/platforms/85xx/mpc85xx_ads.c having way too many
header files included. Clean this up.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated FP unavailable exception to refer to the correct
function in traps.c. head_booke.h was using the old name, KernelFP,
instead of kernel_fp_unavailable_exception.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Registers system call for the powerpc architecture.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With this, new system calls only have to be wired up in one place
for ARCH=ppc and ARCH=powerpc, rather than 2.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved some code around so its usable by more systems than just
the MPC834x SYS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Setup the platform devices needed by the Freescale EHCI USB
host controllers based on a flat device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
LMB_ALLOC_ANYWHERE doesn't need to be part of the API, it's only used in
lmb.c - so move it out of the header file.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently most callers of lmb_alloc() don't check if it worked or not, if it
ever does weird bad things will probably happen. The few callers who do check
just panic or BUG_ON.
So make lmb_alloc() panic internally, to catch bugs at the source. The few
callers who did check the result no longer need to.
The only caller that did anything interesting with the return result was
careful_allocation(). For it we create __lmb_alloc_base() which _doesn't_ panic
automatically, a little messy, but passable.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
