Most ARM machines don't need a special "DMA" memory zone, and
when configured out, the kernel becomes a bit smaller:
| text data bss dec hex filename
|3826182 102384 111700 4040266 3da64a vmlinux
|3823593 101616 111700 4036909 3d992d vmlinux.nodmazone
This is because the system now has only one zone total which effect is
to optimize away many conditionals in page allocation paths.
So let's configure this zone only on machines that need split zones.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...
Signed-off-by: Jürgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable Sparsemem support for LH7A40x SoCs, while still allowing the
existing discontig support for the time being.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Orion-1-90 (88F6183) is another member of the Orion SoC family,
which has a 16 bit DDR2 interface, one x1 PCIe port (configurable as
Root Complex or Endpoint), one 10/100/1000 ethernet interface, one
USB 2.0 port with PHY, one SPDIF/I2S interface, one SDIO interface,
one TWSI interface, two UARTs, one SPI interface, a NAND controller,
a crypto engine, and a 4-channel DMA engine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Switch DaVinci SOC gpios over to using the new GPIO library, so it can
access GPIO expanders and other non-SOC GPIOs using the same calls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
HAVE_AOUT doesn't quite do the same thing as the recently removed
ARCH_SUPPORTS_AOUT config option. That was set even on platforms where
binfmt_aout isn't supported, although it's not entirely clear why.
So it's best just to introduce a new symbol, handled consistently with
other similar HAVE_xxx symbols; with a simple 'select' in the arch Kconfig.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a config option (CONFIG_VMSPLIT_*) to allow choosing
between 3:1, 2:2 and 1:3 user:kernel memory splits.
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Oprofile kernel support for ARMv7.
Tested on OMAP3430 and OMAP3530 chipsets (Cortex-A8).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.
This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone. Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds kernel build support for the regulator core.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (21 commits)
x86/PCI: use dev_printk when possible
PCI: add D3 power state avoidance quirk
PCI: fix bogus "'device' may be used uninitialized" warning in pci_slot
PCI: add an option to allow ASPM enabled forcibly
PCI: disable ASPM on pre-1.1 PCIe devices
PCI: disable ASPM per ACPI FADT setting
PCI MSI: Don't disable MSIs if the mask bit isn't supported
PCI: handle 64-bit resources better on 32-bit machines
PCI: rewrite PCI BAR reading code
PCI: document pci_target_state
PCI hotplug: fix typo in pcie hotplug output
x86 gart: replace to_pages macro with iommu_num_pages
x86, AMD IOMMU: replace to_pages macro with iommu_num_pages
iommu: add iommu_num_pages helper function
dma-coherent: add documentation to new interfaces
Cris: convert to using generic dma-coherent mem allocator
Sh: use generic per-device coherent dma allocator
ARM: support generic per-device coherent dma mem
Generic dma-coherent: fix DMA_MEMORY_EXCLUSIVE
x86: use generic per-device dma coherent allocator
...
This fixes a merge goof whereby ARCH_EP93XX got the "select HAVE_CLK" line
which belongs instead with ARCH_AT91.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
7444a72eff caused these platforms to lose
their GPIOLIB configuration. Convert the missed Kconfig symbols using:
sed -i s/HAVE_GPIO_LIB/ARCH_REQUIRE_GPIOLIB/ arch/arm/Kconfig arch/arm/plat-s3c24xx/Kconfig
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.
Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the ARCH=arm specific a kgdb backend, originally
written by Deepak Saxena <dsaxena@plexity.net> and George Davis
<gdavis@mvista.com>. Geoff Levand <geoffrey.levand@am.sony.com>,
Nicolas Pitre, Manish Lachwani, and Jason Wessel have contributed
various fixups here as well.
The KGDB patch makes one change to the core ARM architecture such that
the traps are initialized early for use with the debugger or other
subsystems.
[ mingo@elte.hu: small cleanups. ]
[ ben-linux@fluff.org: fixed early_trap_init ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Deepak Saxena <dsaxena@plexity.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
This patch brings support for gpio/gpiolib framework to Intel IOP3xx
platforms.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds timer support for the i.MX machine family. This code can
be used on the following machs:
- i.MX1 (tested)
- i.MX2 (i.MX21 (to be tested), i.MX27 (tested))
- i.MX3 (i.MX31 (tested))
TODO: It seems impossible to build a kernel for more than one CPU because the
timer do not follow the platform device rules. So it does only work if
timer 1 can be accessed on all CPUs at the same address.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch bases on the one from Daniel Mack. The most important change to
Daniel's patch is to be more generic. This gpio routine supports at least
the i.MX27 and i.MX31 processors.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Acked-by: Daniel Mack <daniel@caiaq.de>
ARM architecture is not using __do_IRQ
Acked-By: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use HAVE_PATA_PLATFORM for ARCH_RPC
Cc: Linux ARM Kernel <linux-arm-kernel@lists.arm.linux.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This converts arm to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single().
Fixups and testing done by Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The Marvell Discovery Duo (MV78xx0) is a family of ARM SoCs featuring
(depending on the model) one or two Feroceon CPU cores with 512K of L2
cache and VFP coprocessors running at (depending on the model) between
800 MHz and 1.2 GHz, and features a DDR2 controller, two PCIe
interfaces that can each run either in x4 or quad x1 mode, three USB
2.0 interfaces, two 3Gb/s SATA II interfaces, a SPI interface, two
TWSI interfaces, a crypto accelerator, IDMA/XOR engines, a SPI
interface, four UARTs, and depending on the model, two or four gigabit
ethernet interfaces.
This patch adds basic support for the platform, and allows booting
on the MV78x00 development board, with functional UARTs, SATA, PCIe,
GigE and USB ports.
Signed-off-by: Stanislav Samsonov <samsonov@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.
This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Marvell Loki (88RC8480) is an ARM SoC based on a Feroceon CPU
core running at between 400 MHz and 1.0 GHz, and features a 64 bit
DDR controller, 512K of internal SRAM, two x4 PCI-Express ports,
two Gigabit Ethernet ports, two 4x SAS/SATA controllers, two UARTs,
two TWSI controllers, and IDMA/XOR engines.
This patch adds support for the Marvell LB88RC8480 Development
Board, enabling the use of the PCIe interfaces, the ethernet
interfaces, the TWSI interfaces and the UARTs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Available for !SMP only at the moment.
From Russell:
|Basically, if a thread is running on a CPU, thread_saved_fp() is invalid.
|So, the question is: what guarantees do we have here that 'tsk' is not
|running on another CPU?
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Core ftrace support for the ARM architecture, which includes support
for dynamic function tracing.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dyntick is superseded by the clocksource/clockevent infrastructure,
using the NO_HZ configuration option. No one implements dyntick on
ARM anymore, so it's pointless keeping it around. Remove dyntick
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Trying to compile a kerel for ARCH_CO285 fails with the following error:
<-- snip -->
...
CC arch/arm/mach-footbridge/dc21285.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_base_address':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: 'PCICFG0_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:57: error: 'PCICFG1_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_scan_bus':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:286: error: implicit declaration of function 'pci_scan_bus'
...
make[2]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1
<-- snip -->
This does not seem to be a recent breakage.
The ARCH_CO285 support is old - kernel 2.2.0 contains first traces of
it, an it seems to have been pretty complete in later 2.2 kernels.
Since it seems to be completely dead code now this patch therefore
removes it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h
It turns out this was done for ARM, and we can simply always select
HAVE_IDE on ARM instead of manually tracking which platforms might
possible have an IDE controller directly or indirectly.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
Source drivers/uio/Kconfig to make UIO available in menuconfig if ARCH=arm.
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the generic GPIO lib to the EP93xx family. The gpio
handling code has been moved from core.c to a new file called gpio.c.
The GPIO based IRQ code has not been changed.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the PB11MPCore support to the corresponding Kconfig
and Makefile to enable building.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
d142b6e77d added clock source support,
now it's time for the clock event support.
Tested-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Create arch/arm/plat-orion/, for peripherals shared between various
Marvell Orion SoCs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Wed, Feb 20, 2008 at 11:50:33AM +0100, Guennadi Liakhovetski wrote:
> arch/arm/kernel/atags.c uses for some reason the
> KEXEC_BOOT_PARAMS_SIZE macro, which is only defined if CONFIG_KEXEC
> is set. So, either this macro should be defined always, or another
> macro should be used, or ATAGS_PROC should depend on KEXEC.
As the procfs export of ATAGS is not meant as a stable, general purpose
ABI it shouldn't be an independent, general configuration option.
This patch make ATAGS_PROC depend on KEXEC
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark arches that support A.OUT format by including the following in their
master Kconfig files:
config ARCH_SUPPORTS_AOUT
def_bool y
This should also be set if the arch provides compatibility A.OUT support for
an older arch, for instance x86_64 for i386 or sparc64 for sparc.
I've guessed at which arches don't, based on comments in the code, however I'm
sure that some of the ones I've marked as 'yes' actually should be 'no'.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds dummy local timers for each CPU so that the board clock
device is used to broadcast events to the other CPUs. The patch also
adds the declaration for the dummy_timer_setup function (the equivalent
of local_timer_setup when CONFIG_LOCAL_TIMERS is not set).
Due to the way clockevents work, the dummy timer on the first CPU has to
be registered before the board timer.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch updates the RealView code to the clockevents infrastructure.
The SMP support is implemented in subsequent patches. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch updates the RealView platform code to use the generic
clocksource infrastructure for basic time keeping. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the atags used by kexec are fixed to the ones originally used
to boot the kernel. This is less than ideal as changing the commandline,
initrd and other options would be a useful feature.
This patch exports the atags used for the current kernel to userspace
through an "atags" file in procfs. The presence of the file is
controlled by its own Kconfig option and cleans up several ifdef blocks
into a separate file. The tags for the new kernel are assumed to be at
a fixed location before the kernel image itself. The location of the
tags used to boot the original kernel is unimportant and no longer
saved.
Based on a patch from Uli Luckas <u.luckas@road.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After seeing the filename I'd have expected something about the
implementation of SMP in the Linux kernel - not some notes on kernel
configuration and building trivialities noone would search at this
place.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config KPROBES_SUPPORT
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
- Use HAVE_KPROBES
- Use a select
- Yet another update :
Moving to HAVE_* now.
- Update ARM for kprobes support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config ARCH_SUPPORTS_KPROBES
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
Changelog :
- Moving to HAVE_*.
- Add AVR32 oprofile.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The conflicting commit for
move-kconfiginstrumentation-to-arch-kconfig-and-init-kconfig.patch
is the ARM fix from Linus :
commit 38ad9aebe7
He just seemed to agree that my approach (just putting the missing ARM
config options in arch/arm/Kconfig) works too. The main advantage it has
is that it is smaller, does not need a cleanup in the future and does
not break the following patches unnecessarily.
It's just been discussed here
http://lkml.org/lkml/2008/1/15/267
However, Linus might prefer to stay with his own patch and I would
totally understand it that late in the release cycle. Therefore I submit
this for the next release cycle.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
A HOWTO that hasn't been updated for half a dozen years no longer
"contains valuable information about which PCI hardware does work under
Linux and which doesn't".
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The break_lock data structure and code for spinlocks is quite nasty.
Not only does it double the size of a spinlock but it changes locking to
a potentially less optimal trylock.
Put all of that under CONFIG_GENERIC_LOCKBREAK, and introduce a
__raw_spin_is_contended that uses the lock data itself to determine whether
there are waiters on the lock, to be used if CONFIG_GENERIC_LOCKBREAK is
not set.
Rename need_lockbreak to spin_needbreak, make it use spin_is_contended to
decouple it from the spinlock implementation, and make it typesafe (rwlocks
do not have any need_lockbreak sites -- why do they even get bloated up
with that break_lock then?).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors. It's about time we applied one.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apparantly, the generic time subsystem can accurately emulate periodic
mode via the one-shot support code, so we don't need our own periodic
emulation code anymore. Just ensure that we build support for one shot
into the generic time subsystem.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
serial, NOR, PCI and Ethernet is activated at the moment.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for PCI and PCI-E controllers in the
Orion, Orion-NAS and Orion2.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Marvell Orion is a family of ARM SoCs with a DDR/DDR2 memory
controller, 10/100/1000 ethernet MAC, and USB 2.0 interfaces,
and, depending on the specific model, PCI-E interface, PCI-X
interface, SATA controllers, crypto unit, SPI interface, SDIO
interface, device bus, NAND controller, DMA engine and/or XOR
engine.
This contains the basic structure and architecture register definitions.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Feroceon is a family of independent ARMv5TE compliant CPU core
implementations, supporting a variable depth pipeline and out-of-order
execution. The Feroceon is configurable with VFP support, and the
later models in the series are superscalar with up to two instructions
per clock cycle.
This patch adds the initial low-level cache/TLB handling for this core.
Signed-off-by: Assaf Hoffman <hoffman@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes HZ configurable on AT91, following the model used on OMAP.
It defaults to a power of two on AT91rm9200 chips, avoiding rounding
errors which come from dividing a 32 KiHz clock to generate scheduler
irqs; and uses 100 on AT91sam926x chips, using MCK/16 (multi-MHZ).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Remy Bhmer <linux@bohmer.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
