Older versions of kexec-tools has a zImage loader that
passes a virtual address as entry point. The elf loader
otoh it passes a physical address as entry point, and
pages are always passed as physical addresses as well.
Only allow physical addresses from now on.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Save and restore ftrace state when returning from kexec jump in
machine_kexec(). Follows the x86 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For the time being, this creates far more problems than it solves,
evident by the second local_irq_disable(). Kill all of this off
and rely on IRQ disabling to protect against the VBR reload.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add kexec jump support to the SuperH architecture.
Similar to the x86 implementation, with the following
exceptions:
- Instead of separating the assembly code flow into
two parts for regular kexec and kexec jump we use a
single code path. In the assembly snippet regular
kexec is just kexec jump that never comes back.
- Instead of using a swap page when moving data between
pages the page copy assembly routine has been modified
to exchange the data between the pages using registers.
- We walk the page list twice in machine_kexec() to
do and undo physical to virtual address conversion.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the kexec code to avoid using P2SEG. Instead
we walk the page list in machine_kexec() and convert
the addresses from physical to virtual using C.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Setup the vbr register in machine_kexec(). This
instead of passing values to the assembly snippet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
http://marc.info/?t=123609820900002&r=1&w=2http://marc.info/?t=123660375800003&r=1&w=2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While harmless, PTEA has different semantics on these parts, and is only
used in extended TLB mode. Kill off the legacy support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ for sh_eth of sh7763rdp became multi handling.
Therefore, the IRQ number of sh_eth is changed, too.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When SuperH CPU has IRQ multi of DMAC, SH_DMA_IRQ_MULTI becomes enable.
The following CPU's are Multi IRQ of DMAC now.
- SH775X and SH7091
- SH776X
- SH7780
- SH7785
If SH_DMA_IRQ_MULTI becomes enable, dma-sh api driver is optimized
for Multi IRQ.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
dma-sh's get_dma_error_irq() is only used by SH4, as the SH3
doesn't have the DMA Error interrupt.
Disable it out for non-SH4 builds.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements preliminary suspend/resume support for the PMB.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.
This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.
This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the problem that cannot work a PCI device when 32-bit physical
address mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4d7) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was accidentally dropped in the multiple vectors per irq conversion.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the recent entry.S refactoring, the SH-X3 path had a mov.l for a
register to register copy, resulting in:
AS arch/sh/kernel/cpu/sh4/../sh3/entry.o
arch/sh/kernel/cpu/sh4/../sh3/entry.S: Assembler messages:
arch/sh/kernel/cpu/sh4/../sh3/entry.S:366: Error: invalid operands for opcode
make[3]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
Switch it over to a mov to fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7785 hardware
blocks such as SCIF/DMAC/PCIC5/MMCIF/GDTA/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7780 hardware
blocks such as SCIF/RTC/DMAC/PCIC5/MMCIF/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix iounmap() of pass-through P4 addresses. Without this patch
iounmap() on the sh7780 rtc area results in a warning message.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-3 does not support 'pref'-based prefetching, only SH-2A and SH-4A
parts do. Remove SH-3 from the list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register restore code in
the following ways:
- break out restore_regs() from restore_all()
- the register saving order is unchanged
- use restore_regs() in sh_bios_handler and restore_all
- document the function
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
- break out prepare_stack_save_dsp() from handle_exception()
- break out save_regs() from handle_exception()
- the register saving order is unchanged
- align new functions to fit in cache lines
- separate exception code from interrupt code
- keep main code flow in a single cache line per exception vector
- use bsr/rts for regular functions (save pr first)
- keep data in one shared cache line (exception_data)
- document the functions
- tie in the hp6xx code
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change depends on some v4l changes that have been pushed back to
2.6.30, so drop this and fall back on the old soc_camera code until then.
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
None of the other platforms use this, and need individual porting.
Restrict it back to the supported set of CPU subtypes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
GENERIC_TIME still depends on the clocksource bits being there, which is
presently not supported. This allows the CMT clockevent driver to be used
alongside alternate system timers that do not yet provide a clocksource
of their own (MTU2 and so on in the case of SH-2A).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CMT platform data for SuperH Mobile sh7723/sh7722/sh7343/sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SuperH CMT clockevent driver.
Both 16-bit and 32-bit CMT versions are supported, but only 32-bit
is tested. This driver contains support for both clockevents and
clocksources, but no unregistration is supported at this point.
Works fine as clock source and/or event in periodic or oneshot mode.
Tested on sh7722 and sh7723, but should work with any cpu/architecture.
This version is lacking clocksource and early platform driver support
for now - this to minimize the amount of dependencies.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add TMU disable support so we can use other clockevents.
Also, setup the clockevent rating.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework and simplify the sched_clock and clocksource code. Instead
of registering the clocksource in a shared file we move it into the
tmu driver. Also, add code to handle sched_clock in the case of no
clocksource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix macros start_thread and user_stack_pointer.
When these macros aren't called with a variable named regs as second
argument, this will result in a build failure.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that atomic_t is a generic opaque type for all architectures, it is
unwise to use intimate knowledge of its internals when manipulating it.
Instead of relying on the "counter" member being at offset 0 from the
beginning of an atomic_t, explicitly reference the member. This guards
us from any changes to the layout of the beginning of the atomic_t type.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When dereferencing the memory address contained in a register and
modifying the value at that memory address, the register should not be
listed in the inline asm outputs. The value at the memory address is an
output (which is taken care of with the "memory" clobber), not the register.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This corrects a deadlock encountered on ap325 in the cases where the
mutex is contended and the slow-path needs to be fallen back upon.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The T-bit manipulation for syscall error checking had the side effect of
spuriously returning ERESTART* errno values over EINTR. So, we simplify
the error checking a bit and leave the T-bit alone.
Reported-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a bug in the FPU exception handler for the FCNVDS instruction.
To get the register number the instruction is shifted right by 9,
though it should be shifted right by 8.
More information at ST Linux bugzilla:
https://bugzilla.stlinux.com/show_bug.cgi?id=4892
Signed-off-by: Giuseppe Di Giore <giuseppe.di-giore@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In rare circumstances csum_partial() can be called with data which is
not 16 or 32 bit aligned. This is been observed with RPC calls for NFS
file systems for example. Add support for handling this without resorting
to the misaligned fixup code (which is why this hasn't been seen as a
problem). This mimics the i386 version, which has had this support for
some time.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the ap325 defconfig to include
ov772x camera driver.
Old camera is still supported.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch add ov772x camera settings to ap325,
Old camera is still supported. And it will be 2nd camera
if you select ov772x and soc_camera_platform in same time.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Migo-R defconfig to include
ov772x camera and tw9910 video driver
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix up the build for mach-highlander and mach-rsk. These operated on the
assumption that GENERIC_GPIO support with an optional GPIOLIB was
possible. This used to be true, but has not been the case since commit-id
d56cc8bc661ac1ceded8d45ba2d53bb134fee17d ("sh: use gpiolib"), where the
GENERIC_GPIO implementation was rewritten to use GPIOLIB directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CPUs define pinmux tables through the optional interface, while boards
that require demux of their own require it explicitly. Roll the Makefile
rules back to depend on GENERIC_GPIO, which covers both cases.
Fixes a link error with an undefined reference to register_pinmux() on
optional platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch optimizes the gpio data register handling for gpio_set_value().
Instead of using the good old spinlock-plus-read-modify-write strategy
we now use a shadow register and atomic operations.
This improves the bitbanging mmc performance on Migo-R from 26 Kbytes/s
to 40 Kbytes/s.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch separates the register read and write functions to
allow lockless gpio_get_value().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
