This patch fix the following Section mismatch warnings in powerpc code.
WARNING: arch/powerpc/platforms/built-in.o - Section mismatch: reference to .init.data:mv643xx_eth_pd_devs from .text between 'mv643xx_eth_add_pds' (at offset 0x9ed2) and 'gg2_read_config'
WARNING: arch/powerpc/platforms/built-in.o - Section mismatch: reference to .init.data:mv643xx_eth_pd_devs from .text between 'mv643xx_eth_add_pds' (at offset 0x9ed6) and 'gg2_read_config'
WARNING: arch/powerpc/platforms/built-in.o - Section mismatch: reference to .init.text:note_scsi_host from __ksymtab between '__ksymtab_note_scsi_host' (at offset 0x8) and '__ksymtab_sys_ctrler'
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows "hotplugging" of CPUs on G5 machines. CPUs that are
disabled are put into an idle loop with the decrementer frequency set
to minimum. To wake them up again we kick them just like when bringing
them up. To stop those CPUs from messing with any global state we stop
them from entering the timer interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 0fba3a1f39 (a very long time ago,
May 2006), I fixed a bug that caused powermacs to crash when you tried
entering standby/mem suspend states.
As I'm now getting more familiar with the suspend code I notice a few
more things:
1. we previously misunderstood what pm_ops is for, it isn't supposed to be
for doing platform dependent suspend/resume stuff that needs to be done
for suspend to disk (as we currently try to use it!), it is instead for
entering platform dependent suspend states ("standby", "mem").
2. due to the first point, we never properly save FPU and altivec states
when suspending to disk. It probably hasn't hurt yet because the process
that writes the "disk" to /sys/power/state uses neither and its context
is used.
This patch addresses these points as follows:
1. remove all pm_ops from powermac, powermac suspend to ram isn't currently
usable via /sys/power/state but is done via the PMU instead.
2. move the code responsible for storing FPU/altivec state into
save_processor_state and the set_context() call to restore_processor_state.
3. add a call to kernel_enable_spe()
It may look like there is some code removal missing but that is
actually because the new suspend.h file overrides the ppc/suspend.h
one which was previously used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove unneeded inclusion of linux/ide.h
It does not compile with CONFIG_BLOCK=n.
Remove asm/ide.h from ksyms file, it gets included earlier via
linux/ide.h.
Compile tested with all defconfig files.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge 32 and 64 bits asm-powerpc/io.h
The rework on io.h done for the new hookable accessors made it easier,
so I just finished the work and merged 32 and 64 bits io.h for arch/powerpc.
arch/ppc still uses the old version in asm-ppc, there is just too much gunk
in there that I really can't be bothered trying to cleanup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch first splits of_device.c and of_platform.c, the later containing
the bits relative to of_platform_device's. On the "breaks" side of things,
drivers uisng of_platform_device(s) need to include asm/of_platform.h now
and of_(un)register_driver is now of_(un)register_platform_driver.
In addition to a few utility functions to locate of_platform_device(s),
the main new addition is of_platform_bus_probe() which allows the platform
code to trigger an automatic creation of of_platform_devices for a whole
tree of devices.
The function acts based on the type of the various "parent" devices encountered
from a provided root, using either a default known list of bus types that can be
"probed" or a passed-in list. It will only register devices on busses matching
that list, which mean that typically, it will not register PCI devices, as
expected (since they will be picked up by the PCI layer).
This will be used by Cell platforms using 4xx-type IOs in the Axon bridge
and can be used by any embedded-type device as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dev_t boot_dev is declared in arch/powerpc/kernel/setup_32.c
and in arch/powerpc/kernel/setup_64.c but not used in these files.
It is only used in arch/powerpc/platforms/powermac/setup.c, so make
it static in this file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powermac platform & macintosh driver changes.
Built for pmac32_defconfig, g5_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the new irq remapper core and removes the old one. Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).
This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.
For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259. That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.
The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Initialise the ppc_md htab callbacks earlier, in the probe routines. This
allows us to call htab_finish_init() from htab_initialize(), and makes it
private to hash_utils_64.c. Move htab_finish_init() and make_bl() above
htab_initialize() to avoid forward declarations.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a vdso_base element to the mm_context_t for 32-bit compiles
(both for ARCH=powerpc and ARCH=ppc). This fixes the compile errors
that have been reported in arch/powerpc/kernel/signal_32.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
For a very long time, echoing 'standby' or 'mem' into /sys/power/state has
killed the machine on powerpc. This patch fixes that.
This patch adds the .valid callback to pm_ops on PowerMac so that only the
suspend to disk state can be entered. Note that just returning 0 would
suffice since the upper layers don't pass PM_SUSPEND_DISK down, but we
handle it there regardless just in case that changes.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This unifies the 32-bit (ARCH=ppc and ARCH=powerpc) and 64-bit idle
loops. It brings over the concept of having a ppc_md.power_save
function from 32-bit to ARCH=powerpc, which lets us get rid of
native_idle(). With this we will also be able to simplify the idle
handling for pSeries and cell.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes incorrect setting of powersave_nap to 1 on all
PowerMacs, potentially causing memory corruption on some models. This
bug was introuced by me during the 32/64 bits merge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
remove extern declarations of pmac_newworld
move pmac_newworld to bss
if there is any "interrupt-controller" device, then it is newworld.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pmac_setup_arch is only used in the file that it is defined in,
so it should not be in the global namespace.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the continuation of the previous patch. This one removes the old
PowerMac i2c drivers (i2c-keywest and i2c-pmac-smu) and replaces them
both with a single stub driver that uses the new PowerMac low i2c layer.
Now that i2c-keywest is gone, the low-i2c code is extended to support
interrupt driver transfers. All i2c busses now appear as platform
devices. Compatibility with existing drivers should be maintained as the
i2c bus names have been kept identical, except for the SMU bus but in
that later case, all users has been fixed.
With that patch added, matching a device node to an i2c_adapter becomes
trivial.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the first part of a rework of the PowerMac i2c code. It
completely reworks the "low_i2c" layer. It is now more flexible,
supports KeyWest, SMU and PMU i2c busses, and provides functions to
match device nodes to i2c busses and adapters.
This patch also extends & fix some bugs in the SMU driver related to i2c
support and removes the clock spreading hacks from the pmac feature code
rather than adapting them to the new API since they'll be replaced by
the platform function code completely in patch 3/5
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added a common udbg_progress for use by ppc_md.progress()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implementing the machine_crash_shutdown which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Disable the
interrupts, shootdown cpus using debugger IPI and collect regs
for all CPUs.
elfcorehdr= specifies the location of elf core header stored by
the crashed kernel. This command line option will be passed by
the kexec-tools to capture kernel.
savemaxmem= specifies the actual memory size that the first kernel
has and this value will be used for dumping in the capture kernel.
This command line option will be passed by the kexec-tools to
capture kernel.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
CPU freq support using 970FX powertune facility for iMac G5 and SMU
based single CPU desktop.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently there is no Kconfig symbol to indicate that we want nvram
support on 64-bit kernels; it's assumed we always want it, so make
the powermac setup code always initialize the pmac nvram code if
64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Removed of_show_percpuinfo and just report CPU frequency in generic
show_cpuinfo code.
* Killed OCP and PPC_SYS related code which doesn't belong in the
merge tree
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Old powermacs have a number of differences from current machines:
- there is no interrupt tree in the device tree, just interrupt
or AAPL,interrupt properties
- the chosen node in the device tree is called /chosen@0
- the OF claim method doesn't map the memory, so we have to do
an explicit map call as well
- there is no /chosen/cpu property on SMP machines
- the NVRAM isn't structured as a set of partitions.
This adapts the merged powermac support code to cope with these
issues.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This brings in a lot of changes from arch/ppc64/kernel/pmac_*.c to
arch/powerpc/platforms/powermac/*.c and makes various minor tweaks
elsewhere. On the powermac we now initialize ppc_md by copying
the whole pmac_md structure into it, which required some changes in
the ordering of initializations of individual fields of it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
I missed a few places where ppc code was still assuming that the
ppc_md.show_[per]cpuinfo functions returned int.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few things change for consistency between ppc32 and ppc64:
idle functions return void; *_get_boot_time functions return
unsigned long (i.e. time_t) rather than filling in a struct rtc_time
(since that's useful to the callers and easier for pmac to
generate); *_get_rtc_time and *_set_rtc_time functions take
a struct rtc_time; irq_canonicalize is gone; nvram_sync returns
void.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes platform code use the smp_ops variable directly instead
of ppc_md.smp_ops, removes the two unused `data' and `wait' arguments
from the *_message_pass() functions, and removes the call to the
never-implemented smp_ops->space_timers() function.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the files are now in arch/powerpc/platforms/powermac, the
pmac_ prefix that they had is redundant.
Signed-off-by: Paul Mackerras <paulus@samba.org>
