Commit Graph

154602 Commits

Author SHA1 Message Date
Ville Syrjala
ee905d0c58 atyfb: fix alignment for block writes
Block writes require 64 byte alignment.  Since block writes could be used
with SGRAM or WRAM also refine the memory type detection to check for
either type before deciding to use the 64 byte alignment.

Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:01 -07:00
Ville Syrjala
eafad22a05 atyfb: fix HP OmniBook 500 reboot hang
Apparently HP OmniBook 500's BIOS doesn't like the way atyfb reprograms
the hardware. The BIOS will simply hang after a reboot. Fix the problem
by restoring the hardware to it's original state on reboot.

Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:01 -07:00
Baruch Siach
50efacf671 gpio: pl061: fix IRQ handling for GPIOs >= PL061_GPIO_NR
IRQ handling is wrong for any GPIO >= PL061_GPIO_NR.

Fix this by implementing and using a proper .to_irq method.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:01 -07:00
Baruch Siach
79d7f4ee23 gpio: pl061: fix probe error handling code
Note that IRQ has not been initialized when kmalloc() fails.

Also, use DECLARE_BITMAP() to make the code clearer.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:01 -07:00
Yinghai Lu
66918dcdf9 x86: only clear node_states for 64bit
Nathan reported that

| commit 73d60b7f74
| Author: Yinghai Lu <yinghai@kernel.org>
| Date:   Tue Jun 16 15:33:00 2009 -0700
|
|    page-allocator: clear N_HIGH_MEMORY map before we set it again
|
|    SRAT tables may contains nodes of very small size.  The arch code may
|    decide to not activate such a node.  However, currently the early boot
|    code sets N_HIGH_MEMORY for such nodes.  These nodes therefore seem to be
|    active although these nodes have no present pages.
|
|    For 64bit N_HIGH_MEMORY == N_NORMAL_MEMORY, so that works for 64 bit too

unintentionally and incorrectly clears the cpuset.mems cgroup attribute on
an i386 kvm guest, meaning that cpuset.mems can not be used.

Fix this by only clearing node_states[N_NORMAL_MEMORY] for 64bit only.
and need to do save/restore for that in find_zone_movable_pfn

Reported-by: Nathan Lynch <ntl@pobox.com>
Tested-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:01 -07:00
Nikanth Karthikesan
b37f2d4de6 cpusets: document adding/removing cpus to cpuset elaborately
By writing a tasks's pid to the file, a process adds that task to that
cgroup/cpuset.  But to add a cpu/mem to a cpuset, the new list of cpus
should be written to the cpuset.mems file which would replace the old list
of cpus.  Make this clearer in the documentation.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:01 -07:00
Richard Kennedy
d7831a0bdf mm: prevent balance_dirty_pages() from doing too much work
balance_dirty_pages can overreact and move all of the dirty pages to
writeback unnecessarily.

balance_dirty_pages makes its decision to throttle based on the number of
dirty plus writeback pages that are over the calculated limit,so it will
continue to move pages even when there are plenty of pages in writeback
and less than the threshold still dirty.

This allows it to overshoot its limits and move all the dirty pages to
writeback while waiting for the drives to catch up and empty the writeback
list.

A simple fio test easily demonstrates this problem.

fio --name=f1 --directory=/disk1 --size=2G -rw=write --name=f2 --directory=/disk2 --size=1G --rw=write --startdelay=10

This is the simplest fix I could find, but I'm not entirely sure that it
alone will be enough for all cases.  But it certainly is an improvement on
my desktop machine writing to 2 disks.

Do we need something more for machines with large arrays where
bdi_threshold * number_of_drives is greater than the dirty_ratio ?

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:01 -07:00
Renaud Lottiaux
df279ca896 bsdacct: fix access to invalid filp in acct_on()
The file opened in acct_on and freshly stored in the ns->bacct struct can
be closed in acct_file_reopen by a concurrent call after we release
acct_lock and before we call mntput(file->f_path.mnt).

Record file->f_path.mnt in a local variable and use this variable only.

Signed-off-by: Renaud Lottiaux <renaud.lottiaux@kerlabs.com>
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
Joe Perches
b4f90189dc MAINTAINERS: STARFIRE/DURALAN update
Ion's cs.columbia.edu email address no longer works.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ion Badulescu <ionut@badula.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
Zhang Rui
8bc1ad7dd3 kernel/resource.c: fix sign extension in reserve_setup()
When the 32-bit signed quantities get assigned to the u64 resource_size_t,
they are incorrectly sign-extended.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13253
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9905

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reported-by: Leann Ogasawara <leann@ubuntu.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Reported-by: <pablomme@googlemail.com>
Tested-by: <pablomme@googlemail.com>
Cc: <stable@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
David Brownell
529ba0d966 spi: bitbang bugfix in message setup
Bugfix to spi_bitbang infrastructure: make sure to always set transfer
parameters on the first pass through the message's per-transfer loop.
This can matter with drivers that replace the per-word or per-buffer
transfer primitives, on busses with multiple SPI devices.

Previously, this could have started messages using the settings left after
previous messages.  The problem was observed when a high speed chip
(m25p80 type flash) was running very slowly because a low speed device
(avr8 microcontroller) had previously used the bus.  Similar faults could
have driven the low speed device too fast, or used an unexpected word
size.

Acked-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
Krzysztof Helt
537a1bf059 fbdev: add mutex for fb_mmap locking
Add a mutex to avoid a circular locking problem between the mm layer
semaphore and fbdev ioctl mutex through the fb_mmap() call.

Also, add mutex to all places where smem_start and smem_len fields change
so the mutex inside the fb_mmap() is actually used.  Changing of these
fields before calling the framebuffer_register() are not mutexed.

This is 2.6.31 material.  It removes one lockdep (fb_mmap() and
register_framebuffer()) but there is still another one (fb_release() and
register_framebuffer()).  It also cleans up handling of the smem_start and
smem_len fields used by mutexed section of the fb_mmap().

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
David Brownell
70d6027ff2 spi: add spi_master flag word
Add a new spi_master.flags word listing constraints relevant to that
controller.  Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.

Have the mmc_spi host be the first customer of this flag.  Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.

(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies.  Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
David Brownell
b55f627fee spi: new spi->mode bits
Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:

 * SPI_NO_CS ... a second 3-wire variant, where the chipselect
   line is removed instead of a data line; transfers are still
   full duplex.

   This obviously has STRONG protocol implications since the
   chipselect transitions can't be used to synchronize state
   transitions with the SPI master.

 * SPI_READY ... defines open drain signal that's pulled low
   to pause the clock.  This defines a 5-wire variant (normal
   4-wire SPI plus READY) and two 4-wire variants (READY plus
   each of the 3-wire flavors).

   Such hardware flow control can be a big win.  There are ADC
   converters and flash chips that expose READY signals, but not
   many host controllers support it today.

The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack.  That's a mode most hardware can easily support
(unlike SPI_READY).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
Thomas Gleixner
c49568235d dmapools: protect page_list walk in show_pools()
show_pools() walks the page_list of a pool w/o protection against the list
modifications in alloc/free.  Take pool->lock to avoid stomping into
nirvana.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
Bryan Donlan
4d6c13f87d ext2: return -EIO not -ESTALE on directory traversal through deleted inode
ext2_iget() returns -ESTALE if invoked on a deleted inode, in order to
report errors to NFS properly.  However, in ext[234]_lookup(), this
-ESTALE can be propagated to userspace if the filesystem is corrupted such
that a directory entry references a deleted inode.  This leads to a
misleading error message - "Stale NFS file handle" - and confusion on the
part of the admin.

The bug can be easily reproduced by creating a new filesystem, making a
link to an unused inode using debugfs, then mounting and attempting to ls
-l said link.

This patch thus changes ext2_lookup to return -EIO if it receives -ESTALE
from ext2_iget(), as ext2 does for other filesystem metadata corruption;
and also invokes the appropriate ext*_error functions when this case is
detected.

Signed-off-by: Bryan Donlan <bdonlan@gmail.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
KAMEZAWA Hiroyuki
341c87bf34 elf: limit max map count to safe value
With ELF, at generating coredump, some more headers other than used
vmas are added.

When max_map_count == 65536, a core generated by following kinds of
code can be unreadable because the number of ELF's program header is
written in 16bit in Ehdr (please see elf.h) and the number overflows.

==
	... = mmap(); (munmap, mprotect, etc...)
	if (failed)
		abort();
==

This can happen in mmap/munmap/mprotect/etc...which calls split_vma().

I think 65536 is not safe as _default_ and reduce it to 65530 is good
for avoiding unexpected corrupted core.

Anyway, max_map_count can be enlarged by sysctl if a user is brave..

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jakub Jelinek <jakub@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Yang Shi
b1cfebc923 edac: add DDR3 memory type for MPC85xx EDAC
Since some new MPC85xx SOCs support DDR3 memory now, so add DDR3 memory
type for MPC85xx EDAC.

Signed-off-by: Yang Shi <yang.shi@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Michael Buesch
c4285b47b0 parport/serial: add support for NetMos 9901 Multi-IO card
Add support for the PCI-Express NetMos 9901 Multi-IO card.

0001:06:00.0 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 65
        Region 0: I/O ports at 0030 [size=8]
        Region 1: Memory at 80105000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80104000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.1 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 65
        Region 0: I/O ports at 0020 [size=8]
        Region 1: Memory at 80103000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80102000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.2 Parallel controller [0701]: NetMos Technology Device [9710:9901] (prog-if 03 [IEEE1284])
        Subsystem: Device [a000:2000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 65
        Region 0: I/O ports at 0010 [size=8]
        Region 1: I/O ports at <unassigned>
        Region 2: Memory at 80101000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80100000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: parport_pc
        Kernel modules: parport_pc

[   16.760181] PCI parallel port detected: 416c:0100, I/O at 0x812010(0x0), IRQ 65
[   16.760225] parport0: PC-style at 0x812010, irq 65 [PCSPP,TRISTATE,EPP]
[   16.851842] serial 0001:06:00.0: enabling device (0004 -> 0007)
[   16.883776] 0001:06:00.0: ttyS0 at I/O 0x812030 (irq = 65) is a ST16650V2
[   16.893832] serial 0001:06:00.1: enabling device (0004 -> 0007)
[   16.926537] 0001:06:00.1: ttyS1 at I/O 0x812020 (irq = 65) is a ST16650V2

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Peter Oberparleiter
972c71a318 gcov: fix documentation
Commonly available versions of cp and tar don't work well with special
files created using seq_file.  Mention this problem in the gcov
documentation and update the helper script example to work around these
problems.

Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Tejun Heo
b01e8dc343 alpha: fix percpu build breakage
alpha percpu access requires custom SHIFT_PERCPU_PTR() definition for
modules to work around addressing range limitation.  This is done via
generating inline assembly using C preprocessing which forces the
assembler to generate external reference.  This happens behind the
compiler's back and makes the compiler think that static percpu variables
in modules are unused.

This used to be worked around by using __unused attribute for percpu
variables which prevent the compiler from omitting the variable; however,
recent declare/definition attribute unification change broke this as
__used can't be used for declaration.  Also, in the process,
PER_CPU_ATTRIBUTES definition in alpha percpu.h got broken.

This patch adds PER_CPU_DEF_ATTRIBUTES which is only used for definitions
and make alpha use it to add __used for percpu variables in modules.  This
also fixes the PER_CPU_ATTRIBUTES double definition bug.

Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: maximilian attems <max@stro.at>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Stephen Rothwell
15e3252464 fbdev: work around old compiler bug
When building with a 4.1.x compiler on powerpc64 (at least) we get this
error:

drivers/video/logo/logo_linux_mono.c:81: error: logo_linux_mono causes a section type conflict

This was introduced by commit ae52bb2384
("fbdev: move logo externs to header file").  This is a partial revert of
that commit sufficient to not hit the compiler bug.

Also convert _clut arrays from __initconst to __initdata.

Sam said:

  Al analysed this some time ago.  When we say something is const then
  _sometimes_ gcc annotate the section as const(?) - sometimes not.  So if
  we have two variables/functions annotated __*const and gcc decides to
  annotate the section const only in one case we get a section type
  conflict.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Joe Perches
c15e504bd0 MAINTAINERS: update EDAC-I82975X
As per Ranganathan's request.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: Arvind R. <arvind@jetztechnologies.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Heiko Carstens
2a2325e6e8 gcov: fix __ctors_start alignment
The ctors section for each object file is eight byte aligned (on 64 bit).
However the __ctors_start symbol starts at an arbitrary address dependent
on the size of the previous sections.

Therefore the linker may add some zeroes after __ctors_start to make sure
the ctors contents are properly aligned.  However the extra zeroes at the
beginning aren't expected by the code.  When walking the functions
pointers contained in there and extra zeroes are added this may result in
random jumps.  So make sure that the __ctors_start symbol is always
aligned as well.

Fixes this crash on an allyesconfig on s390:

[    0.582482] Kernel BUG at 0000000000000012 [verbose debug info unavailable]
[    0.582489] illegal operation: 0001 [#1] SMP DEBUG_PAGEALLOC
[    0.582496] Modules linked in:
[    0.582501] CPU: 0 Tainted: G        W  2.6.31-rc1-dirty #273
[    0.582506] Process swapper (pid: 1, task: 000000003f218000, ksp: 000000003f2238e8)
[    0.582510] Krnl PSW : 0704200180000000 0000000000000012 (0x12)
[    0.582518]            R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
[    0.582524] Krnl GPRS: 0000000000036727 0000000000000010 0000000000000001 0000000000000001
[    0.582529]            00000000001dfefa 0000000000000000 0000000000000000 0000000000000040
[    0.582534]            0000000001fff0f0 0000000001790628 0000000002296048 0000000002296048
[    0.582540]            00000000020c438e 0000000001786000 0000000002014a66 000000003f223e60
[    0.582553] Krnl Code:>0000000000000012: 0000                unknown
[    0.582559]            0000000000000014: 0000                unknown
[    0.582564]            0000000000000016: 0000                unknown
[    0.582570]            0000000000000018: 0000                unknown
[    0.582575]            000000000000001a: 0000                unknown
[    0.582580]            000000000000001c: 0000                unknown
[    0.582585]            000000000000001e: 0000                unknown
[    0.582591]            0000000000000020: 0000                unknown
[    0.582596] Call Trace:
[    0.582599] ([<0000000002014a46>] kernel_init+0x622/0x7a0)
[    0.582607]  [<0000000000113e22>] kernel_thread_starter+0x6/0xc
[    0.582615]  [<0000000000113e1c>] kernel_thread_starter+0x0/0xc
[    0.582621] INFO: lockdep is turned off.
[    0.582624] Last Breaking-Event-Address:
[    0.582627]  [<0000000002014a64>] kernel_init+0x640/0x7a0

Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:59 -07:00
Davide Libenzi
133890103b eventfd: revised interface and cleanups
Change the eventfd interface to de-couple the eventfd memory context, from
the file pointer instance.

Without such change, there is no clean way to racely free handle the
POLLHUP event sent when the last instance of the file* goes away.  Also,
now the internal eventfd APIs are using the eventfd context instead of the
file*.

This patch is required by KVM's IRQfd code, which is still under
development.

Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:55:58 -07:00
Jiri Slaby
f7c2df9b55 AFS: Fix lock imbalance
Don't unlock on vfs_rejected_lock path in afs_do_setlk, since the lock
is unlocked after abort_attempt label.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 13:30:44 -07:00
Linus Torvalds
5a4f13fad1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
  ide: memory overrun in ide_get_identity_ioctl() on big endian machines using ioctl HDIO_OBSOLETE_IDENTITY
  ide: fix resume for CONFIG_BLK_DEV_IDEACPI=y
  ide-cd: handle fragmented packet commands gracefully
  ide: always kill the whole request on error
  ide: fix ide_kill_rq() for special ide-{floppy,tape} driver requests
2009-06-29 20:07:43 -07:00
Christian Engelmayer
e18ed145c7 ide: memory overrun in ide_get_identity_ioctl() on big endian machines using ioctl HDIO_OBSOLETE_IDENTITY
This patch fixes a memory overrun in function ide_get_identity_ioctl() which
chooses the size of a memory buffer depending on the ioctl command that led
to the function call, however, passes that buffer to a function which needs the
buffer size to be always chosen unconditionally.

Due to conditional compilation the memory overrun can only happen on big endian
machines. The error can be triggered using ioctl HDIO_OBSOLETE_IDENTITY. Usage
of ioctl HDIO_GET_IDENTITY is safe.

Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29 19:31:41 -07:00
Bartlomiej Zolnierkiewicz
2bf427b25b ide: fix resume for CONFIG_BLK_DEV_IDEACPI=y
commit 2f0d0fd2a6 ("ide-acpi: cleanup
do_drive_get_GTF()") didn't account for the lack of hwif->acpidata
check in generic_ide_suspend() [ indirect user of do_drive_get_GTF()
through ide_acpi_exec_tfs() ] resulting in broken resume when ACPI
support is enabled but ACPI data is unavailable.

Fix it by adding ide_port_acpi() helper for checking if port needs
ACPI handling and cleaning generic_ide_{suspend,resume}() to use it
instead of hiding hwif->acpidata and ide_noacpi checks in IDE ACPI
helpers (this should help in preventing similar bugs in the future).

While at it:
- kill superfluous debugging printks in ide_acpi_{get,push}_timing()

Reported-and-tested-by: Etienne Basset <etienne.basset@numericable.fr>
Also-reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29 19:20:42 -07:00
Linus Torvalds
ec9c45d456 Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (28 commits)
  [ARM] 5562/2: at91: add gpio button support for at91sam9g20ek
  [ARM] 5563/1: at91: at91sam9rlek lcd interface correction
  [ARM] 5565/2: Use PAGE_SIZE and RO_DATA() in link script
  [ARM] 5560/1: Avoid buffer overrun in case of an invalid IRQ
  [ARM] GTA02: build fixes (s3c2410_nand_set usage)
  [ARM] MINI2440: Add missing flash_bbt flat to NAND
  [ARM] s3c2410_defconfig: add MINI2440 machine to build
  [ARM] S3C: Fix S3C24XX build to not include s3c64xx IIS devices
  [ARM] S3C24XX: Fix missing s3c_iis_device.
  [ARM] MINI2440: remove duplicated #include
  [ARM] S3C24XX: Fix spi-bus configuration build errors
  OMAP: Fix IOMEM macro for assembly
  [ARM] S3C: Remove unused CONFIG_DEBUG_S3C_PORT
  [ARM] S3C24XX: Fix use of CONFIG_S3C24XX_PWM
  OMAP2/3: Initialize gpio debounce register
  OMAP: IOMMU: function flush_iotlb_page is not flushing correct entry
  OMAP3: RX51: Use OneNAND sync read / write
  OMAP2/3: gpmc-onenand: correct use of async timings
  OMAP3: DMA: Enable idlemodes for DMA OCP
  OMAP3: SRAM size fix for HS/EMU devices
  ...
2009-06-29 16:18:19 -07:00
Linus Torvalds
aa221cb617 Merge branch 'for-linus' of git://git.infradead.org/users/eparis/notify
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  fs: allow d_instantiate to be called with negative parent dentry
2009-06-29 13:09:39 -07:00
Linus Torvalds
2bfdd79eaa Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: OSS: mpu401, fix deadlock
  ALSA: hda - Add missing initializations for ALC268 and ALC269
  ALSA: cmi8330: fix MPU-401 PnP init copy&paste bug
  ALSA: hda - Line In for Acer Inspire 6530G model
  sound: oxygen: make mic volume control mono
  MAINTAINERS: Add entry for twl4030 series soc codec driver
  ALSA: lx6464es - configure ethersound io channels
  sound: Use PCI_VDEVICE for CREATIVE and ECTIVA
  sound: Use PCI_VDEVICE
  ALSA: hda - Use model=acer-aspire-6530g for Acer Aspire 6930G
  ALSA: hda - Fix acer-aspire-6530g model quirk
  ALSA: hda - Add pin-sense trigger when needed for Realtek codecs
  ALSA: hda - Fix support for Samsung P50 with AD1986A codec
  ALSA: hda - Generalize the pin-detect quirk for Lenovo N100
  ALSA: hda - Simplify AD1986A mixer definitions
2009-06-29 09:46:12 -07:00
Linus Torvalds
bb1e9b844b Merge branch 'bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  integrity: add ima_counts_put (updated)
  integrity: ima audit hash_exists fix
  integrity: ima mq_open imbalance msg fix
2009-06-29 09:44:44 -07:00
Linus Torvalds
e717f33e98 Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  Revert "x86: cap iomem_resource to addressable physical memory"
2009-06-29 09:42:01 -07:00
Linus Torvalds
1bfd4d5860 Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
  backlight: Fix tdo24m crash on kmalloc
2009-06-29 09:41:12 -07:00
Ingo Molnar
44b3615b8c eeepc-laptop: Fix build failure with HOTPLUG_PCI && !SYSFS
FYI, there's a post-rc1 build regression with certain configs:

 drivers/built-in.o: In function `pci_hp_deregister':
 (.text+0xb166): undefined reference to `pci_hp_remove_module_link'
 drivers/built-in.o: In function `pci_hp_deregister':
 (.text+0xb19f): undefined reference to `pci_destroy_slot'
 drivers/built-in.o: In function `__pci_hp_register':
 (.text+0xb583): undefined reference to `pci_create_slot'
 drivers/built-in.o: In function `__pci_hp_register':
 (.text+0xb5b1): undefined reference to `pci_hp_create_module_link'
 make: *** [.tmp_vmlinux1] Error 1

Caused by:

| 2b121bc262 is first bad commit
| commit 2b121bc262
| Date:   Thu Jun 25 13:25:36 2009 +0200
|
|     eeepc-laptop: Register as a pci-hotplug device

which changed the driver to use the PCI hotplug infrastructure, but
didn't do a good job on the Kconfig rules.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-29 09:40:38 -07:00
Alan Cox
aef29bc260 tty: Fix the leak in tty_ldisc_release
Currently we reinit the ldisc on final tty close which is what the old code
did to ensure that if the device retained its termios settings then it had the
right ldisc. tty_ldisc_reinit does that but also leaves us with the reset
ldisc reference which is then leaked.

At this point we know the port will be recycled so we can kill the ldisc
off completely rather than try and add another ldisc free up when the kref
count hits zero.

At this point it is safe to keep the ldisc closed as tty_ldisc waiting
methods are only used from the user side, and as the final close we are
the last such reference. Interrupt/driver side methods will always use the
non wait version and get back a NULL.

Found with kmemleak and investigated/identified by Catalin Marinas.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-29 09:33:26 -07:00
Jiri Slaby
9ea5ca75a2 sound: OSS: mpu401, fix deadlock
mpu401_chk_version is called with a spin lock already held. Don't take it
again.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-06-29 18:05:52 +02:00
Takashi Iwai
580c9d373c Merge branch 'fix/pci-vdevice' into for-linus
* fix/pci-vdevice:
  sound: Use PCI_VDEVICE for CREATIVE and ECTIVA
  sound: Use PCI_VDEVICE
2009-06-29 18:05:09 +02:00
Takashi Iwai
e2cb0d95ba Merge branch 'fix/oxygen' into for-linus
* fix/oxygen:
  sound: oxygen: make mic volume control mono
2009-06-29 18:05:07 +02:00
Takashi Iwai
7d489c460e Merge branch 'fix/misc' into for-linus
* fix/misc:
  ALSA: cmi8330: fix MPU-401 PnP init copy&paste bug
2009-06-29 18:05:06 +02:00
Takashi Iwai
0baddbc895 Merge branch 'fix/lx6464es' into for-linus
* fix/lx6464es:
  ALSA: lx6464es - configure ethersound io channels
2009-06-29 18:05:05 +02:00
Takashi Iwai
cdae219cec Merge branch 'fix/hda-samsung-p50' into for-linus
* fix/hda-samsung-p50:
  ALSA: hda - Fix support for Samsung P50 with AD1986A codec
  ALSA: hda - Generalize the pin-detect quirk for Lenovo N100
  ALSA: hda - Simplify AD1986A mixer definitions
2009-06-29 18:05:04 +02:00
Takashi Iwai
ae77b4ed4f Merge branch 'fix/hda' into for-linus
* fix/hda:
  ALSA: hda - Add missing initializations for ALC268 and ALC269
  ALSA: hda - Line In for Acer Inspire 6530G model
  ALSA: hda - Use model=acer-aspire-6530g for Acer Aspire 6930G
  ALSA: hda - Fix acer-aspire-6530g model quirk
  ALSA: hda - Add pin-sense trigger when needed for Realtek codecs
2009-06-29 18:05:02 +02:00
Jeremy Kerr
e6ce306601 fs: allow d_instantiate to be called with negative parent dentry
The new fsnotify infrastructure (starting at 90586523) causes an oops in
spufs, where we populate a directory with files before instantiating the
directory itself. The new changes seem to have introduced an assumption
that a dentry's parent will be positive when instantiating.

This change makes it once again possible to d_instantiate a dentry
with a negative parent, and brings __fsnotify_d_instantiate() into
line with inotify_d_instantiate(), which already has this NULL check.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
2009-06-29 10:00:58 -04:00
Nicolas Ferre
59c5fe6d84 [ARM] 5562/2: at91: add gpio button support for at91sam9g20ek
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-29 11:19:27 +01:00
Takashi Iwai
1d955ebd4d ALSA: hda - Add missing initializations for ALC268 and ALC269
During the changes to clean up / fix the realtek codec initialization
routines in commit 4a79ba34ca,
I forgot to add the check for ALC268 and ALC269.
This resulted in the missing EAPD and COEF setup for these codecs.

This patch adds the missing checks for these codecs.

Reference: bko#13633
	http://bugzilla.kernel.org/show_bug.cgi?id=13633

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-06-29 11:33:53 +02:00
Ondrej Zary
c2a30d7118 ALSA: cmi8330: fix MPU-401 PnP init copy&paste bug
Fix copy&paste bug in PnP MPU-401 initialization.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-06-29 08:06:10 +02:00
Tony Vroon
684a88429c ALSA: hda - Line In for Acer Inspire 6530G model
The Line In connector is set up as PIN_IN by default, using
VREF_HIZ. It is connected to both ADCs, so add it to both
input selectors.
Also add the ability to use the input mix (on a SoundBlaster
one would call this "What You Hear").

Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-06-29 07:41:08 +02:00
Linus Torvalds
5298976562 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  be2net: Fix to avoid a crash seen on PPC with LRO and Jumbo frames.
  gro: Flush GRO packets in napi_disable_pending path
  inet: Call skb_orphan before tproxy activates
  mac80211: Use rcu_barrier() on unload.
  sunrpc: Use rcu_barrier() on unload.
  bridge: Use rcu_barrier() instead of syncronize_net() on unload.
  ipv6: Use rcu_barrier() on module unload.
  decnet: Use rcu_barrier() on module unload.
  sky2: Fix checksum endianness
  mdio add missing GPL flag
  sh_eth: remove redundant test on unsigned
  fsl_pq_mdio: Fix fsl_pq_mdio to work with modules
  ipv6: avoid wraparound for expired preferred lifetime
  tcp: missing check ACK flag of received segment in FIN-WAIT-2 state
  atl1*: add device_set_wakeup_enable to atl1*_set_wol
  Phonet: generate Netlink RTM_DELADDR when destroying a device
  Phonet: publicize the Netlink notification function
  Revert "veth: prevent oops caused by netdev destructor"
  cpmac: fix compilation failure introduced with netdev_ops conversion
  ipsec: Fix name of CAST algorithm
2009-06-28 19:57:31 -07:00