pfn<<PAGE_SHIFT sometimes extends beyond. The pte is big enough to hold
'long long', but the shift in pfn_pte() needs to do its calculation with
enough bits to hold the result.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
supporting parity errors only for memory (Pmax/3min/Maxine).
Fixes for resources decoded by the KN04/KN05 MB ASIC. Additional
clean-ups for the ECC handler.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
never initialized been initialized anywhere, just saved to and
restored from signal frames so nonsense anyway. As neat side effect
of being shared between all processors it was also abusable as a
nice covert channel between processes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* remove two already unused and commented structures
* added an ULL suffix to several address constants that use bits 35-32
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the 'load_irix_binary' and having kernel faults, Irix support is
disabled. I suspect locking of some sort, but I will now have to
investigate further.
Static IRIX binaries are now being detected properly and are using the
ELF interpreter found in this file.
Signed-off-by: Steven J. Hill <sjhill@realitydiluted.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
binutils are broken and don't warn about this use of $at even though
gas is in .set noat mode so this for now is an accident waiting to
happen.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch from Kenneth Tan
Defining IXP46X peripheral devices memory mapping definitions that have
been missed out:
o Peripheral virtual base address is being adjusted to allow more headroom to add extra peripheral device addresses
o Peripheral size is being increased to address the above needs
o Virtual address of expansion bus and PCI configuration register needs to be adjusted as new peripheral device memory space is overlapping with their virtual address space
Signed-off-by: Kenneth Tan <chong.yin.tan@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Introduce ixp2000_reg_wrb, which is a variant of ixp2000_reg_write
that does a readback from the target register, to make sure that
the write has been flushed out of the write buffer.
Unlike the previous (ineffective) readback in ixp2000_reg_write, this
readback is followed by an instruction that depends on the value of
the readback so that the CPU actually stalls until the readback has
completed.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Turn ixp2000_reg_read into an inline function.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The workaround that we do for avoiding triggering ixp2400 erratum #66
involves mapping I/O pages using XCB=101 instead of XCB=000 so that we
prevent the I/O signal to the gasket from being asserted (which can
cause data corruption.) But XCB=101 mappings are write-buffered while
mappings using XCB=000 are not, which is why if we use XCB=101 mappings
we do a readback for every CSR store in an attempt to make sure that
the store has been pushed out of the xscale core and the gasket.
Unfortunately, there are two issues with this:
- we do a readback for every CSR store, which is wrong, because the
register we are writing to might have unwanted side-effects on read,
for example, in the case of the scratchpad ring enqueue/dequeue
registers; and
- the readback is totally ineffective in the way we currently do it,
because we just issue a load but do not issue any instruction that
depends on the return value of that load, so the xscale core does
not wait for the load to complete before continuing.
See this linux-arm-kernel mailing list post for further information:
http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2005-September/031314.html
This means that my ixp2400 boxes have been running for many months
without a working readback in ixp2000_reg_write, without any apparent
adverse effects. Two of them have been running for a week now with
the actual readback deleted from ixp2000_reg_write, also without any
apparent ill effects.
So, because in its current form it does more harm than good, the
readback in ixp2000_reg_write should simply be killed, as the patch
below does.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Macro arguments should _always_ be surrounded by parentheses
when used to prevent unexpected problems with operator precedence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the machine information structures are now static, the
compiler might optimise them away. Mark them with
__attribute_used__ to prevent this occuring.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
zutil.h does not need errno.h
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a numbers of issues regarding to that both 8xx and 82xx
began to use ppc_sys model:
- Platform is now identified by default deviceless SOC, if no
BOARD_CHIP_NAME is specified in the bard-specific header. For the list
of supported names refer to (arch/ppc/syslib/) mpc8xx_sys.c and
mpc82xx_sys.c for 8xx and 82xx respectively.
- Fixed a bug in identification by name - if the name was not found,
it returned -1 instead of default deviceless ppc_spec.
- fixed devices amount in the 8xx platform system descriptions
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the 85xx platform code to support the new PHY Layer.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <Kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a nvram acccess method, similar to
arch/ppc64/kernel/pSeries_nvram.c tested on CHRP B50.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the phys_mem_access_prot() function to take a pfn instead of an
address. This allows mmap64() to work on /dev/mem for addresses above 4G
on 32-bit architectures. We start with a pfn in mmap_mem(), so there's no
need to convert to an address; in fact, it's actively bad, since the
conversion can overflow when the address is above 4G.
Similarly fix the ppc32 page_is_ram() function to avoid a conversion to an
address by directly comparing to max_pfn. Working with max_pfn instead of
high_memory fixes page_is_ram() to give the right answer for highmem pages.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Expose faster ether compare for use by protocols and other
driver. And change name to be more consistent with other ether
address manipulation routines in same file
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
With CONFIG_PM=n:
drivers/built-in.o(.text+0x1098c): In function `hub_thread':
drivers/usb/core/hub.c:2673: undefined reference to `.dpm_runtime_resume'
drivers/built-in.o(.text+0x10998):drivers/usb/core/hub.c:2674: undefined reference to `.dpm_runtime_resume'
Please, never ever ever put extern decls into .c files. Use the darn header
files :(
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as592) makes a few small improvements to the way device
strings are handled, and it fixes some bugs in a couple of other sysfs
attribute routines. (Look at show_configuration_string() to see what I
mean.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I can't stand text lines that wrap-around in my 80-column windows. This
patch (as589) makes cosmetic changes to a couple of source files.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as587b) improves the implementation of USB endpoint
sysfs files. Instead of storing a whole bunch of attributes for every
single endpoint, each endpoint now gets its own kobject and they can
share a static list of attributes. The number of extra fields added to
struct usb_host_endpoint has been reduced from 4 to 1.
The bEndpointAddress field is retained even though it is redundant (it
repeats the same information as the attributes' directory name). The
code avoids calling kobject_register, to prevent generating unwanted
hotplug events.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter. It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support). And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should let us get rid of all of the different hooks in the USB core for
when something has changed.
Also, some other parts of the kernel have wanted to know this kind of
information at times.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is put into suspend mode, the current drawn from VBUS
has to be less than 500 uA. Some transceivers need to be put into a
special power-saving mode to accomplish this, and won't have a separate
OTG driver handling that.
This adds a suspend method to the "otg_transceiver" struct -- misnamed,
it's not only for OTG -- and calls it from the OMAP UDC driver.
Signed-off-by: Juha Yrj?l? <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The way we're looking at USB suspend lately doesn't expect drivers to
call usb_suspend_device() or usb_resume_device() directly; that'll
be implicit when no interfaces are in use.
This patch removes those APIs from visibility outside usbcore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
drivers/usb/core/hub.c | 12 ++++--------
drivers/usb/core/usb.h | 4 ++++
include/linux/usb.h | 5 -----
3 files changed, 8 insertions(+), 13 deletions(-)
This saves a word from "struct device" ... there's a refcounting mechanism
stub that's rather ineffective (the values are never even tested!), which
can safely be deleted. With this patch it uses normal device refcounting,
so any potential users of the pm_parent mechanism will be more correct.
(That mechanism is actually unusable for now though; it does nothing.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/base/power/main.c | 26 +++-----------------------
include/linux/pm.h | 1 -
2 files changed, 3 insertions(+), 24 deletions(-)
This patch removes the extra usb_suspend_device() parameter. The original
reason to pass that parameter was so that this routine could suspend any
active children. A previous patch removed that functionality ... leaving
no reason to pass the parameter. A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.
On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend. It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 34 +++++++++++++++++++++-------------
drivers/usb/core/usb.c | 23 +++++++++++++++++++++--
drivers/usb/host/ehci-hcd.c | 2 +-
drivers/usb/host/isp116x-hcd.c | 2 +-
drivers/usb/host/ohci-pci.c | 2 +-
include/linux/usb.h | 2 +-
6 files changed, 46 insertions(+), 19 deletions(-)
This patch adds endpoint information for both devices and interfaces to
sysfs. Previously it was only possible to get the endpoint information
from usbfs, and never possible to get any information on endpoint 0.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/sysfs.c | 195 ++++++++++++++++++++++++++++++++++++++++++++++-
include/linux/usb.h | 4
2 files changed, 197 insertions(+), 2 deletions(-)
I told you that the pci_ids.h cleanup was a bad idea ;)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_ids.h cleanup: remove duplicated entries and change some defines to
explicit value rather than in terms of another constant, preparation for
removing unused symbols
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/pci_ids.h | 28 +++++++++-------------------
1 file changed, 9 insertions(+), 19 deletions(-)
Some PCI adapters (eg. ipr scsi adapters) have an exposure today in that they
issue BIST to the adapter to reset the card. If, during the time it takes to
complete BIST, userspace attempts to access PCI config space, the host bus
bridge will master abort the access since the ipr adapter does not respond on
the PCI bus for a brief period of time when running BIST. On PPC64 hardware,
this master abort results in the host PCI bridge isolating that PCI device
from the rest of the system, making the device unusable until Linux is
rebooted. This patch is an attempt to close that exposure by introducing some
blocking code in the PCI code. When blocked, writes will be humored and reads
will return the cached value. Ben Herrenschmidt has also mentioned that he
plans to use this in PPC power management.
Signed-off-by: Brian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/access.c | 89 ++++++++++++++++++++++++++++++++++++++++++++++++
drivers/pci/pci-sysfs.c | 20 +++++-----
drivers/pci/pci.h | 7 +++
drivers/pci/proc.c | 28 +++++++--------
drivers/pci/syscall.c | 14 +++----
include/linux/pci.h | 7 +++
6 files changed, 134 insertions(+), 31 deletions(-)
Rename SCTP specific control message flags to use SCTP_ prefix rather than
MSG_ prefix as per the latest sctp sockets API draft.
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
The new SMBus PEC implementation doesn't support PEC emulation on
non-PEC non-I2C SMBus masters, so we can drop all related code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is my rewrite of the SMBus PEC support. The original
implementation was known to have bugs (credits go to Hideki Iwamoto
for reporting many of them recently), and was incomplete due to a
conceptual limitation.
The rewrite affects only software PEC. Hardware PEC needs very little
code and is mostly untouched.
Technically, both implementations differ in that the original one
was emulating PEC in software by modifying the contents of an
i2c_smbus_data union (changing the transaction to a different type),
while the new one works one level lower, on i2c_msg structures (working
on message contents). Due to the definition of the i2c_smbus_data union,
not all SMBus transactions could be handled (at least not without
changing the definition of this union, which would break user-space
compatibility), and those which could had to be implemented
individually. At the opposite, adding PEC to an i2c_msg structure
can be done on any SMBus transaction with common code.
Advantages of the new implementation:
* It's about twice as small (from ~136 lines before to ~70 now, only
counting i2c-core, including blank and comment lines). The memory
used by i2c-core is down by ~640 bytes (~3.5%).
* Easier to validate, less tricky code. The code being common to all
transactions by design, the risk that a bug can stay uncovered is
lower.
* All SMBus transactions have PEC support in I2C emulation mode
(providing the non-PEC transaction is also implemented). Transactions
which have no emulation code right now will get PEC support for free
when they finally get implemented.
* Allows for code simplifications in header files and bus drivers
(patch follows).
Drawbacks (I guess there had to be at least one):
* PEC emulation for non-PEC capable non-I2C SMBus masters was dropped.
It was based on SMBus tricks and doesn't quite fit in the new design.
I don't think it's really a problem, as the benefit was certainly
not worth the additional complexity, but it's only fair that I at
least mention it.
Lastly, let's note that the new implementation does slightly affect
compatibility (both in kernel and user-space), but doesn't actually
break it. Some defines will be dropped, but the code can always be
changed in a way that will work with both the old and the new
implementations. It shouldn't be a problem as there doesn't seem to be
many users of SMBus PEC to date anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Discard I2C_FUNC_SMBUS_*_PEC defines. i2c clients are not supposed to
check for PEC support of i2c bus drivers on individual SMBus
transactions, and i2c bus drivers are not supposed to advertise them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop unused i2c-over-parallel-port i2c IDs:
* I2C_HW_B_LPC was never actually used as far as I could search.
* I2C_HW_B_ELV and I2C_HW_B_VELLE are no more used since the
introduction of the unified i2c-parport driver in Linux 2.6.2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix several redefinitions of i2c IDs. i2c IDs must not be defined
outside of i2c-id.h.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Henk Vergonet <henk@god.dyndns.org>
Acked-by: Mark McClelland <mark@alpha.dyndns.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver for the Xicor X1205 RTC chip.
Signed-off-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop I2C_SMBUS_I2C_BLOCK_MAX, use I2C_SMBUS_BLOCK_MAX instead.
I2C_SMBUS_I2C_BLOCK_MAX has always been defined to the same value as
I2C_SMBUS_BLOCK_MAX, and this will never change: setting it to a lower
value would make no sense, setting it to a higher value would break
i2c_smbus_data compatibility. There is no point in changing
i2c_smbus_data to support larger block transactions in SMBus mode, as
no SMBus hardware supports more than 32 byte blocks. Thus, for larger
transactions, direct I2C transfers are the way to go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more per-i2c-algorithm adapter max. Last time there were
was in July 1999.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete 2 out-of-date, colliding ioctl defines. I2C_UDELAY and
I2C_MDELAY are supposed to be used by i2c-algo-bit, but actually
aren't (and I suspect never were). Moreover, their values are the same
as I2C_FUNCS and I2C_SLAVE_FORCE, respectively, which *are* widely
used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a misplaced comment in i2c.h. Spotted by Hideki Iwamoto.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CVS revision IDs are totally useless and irrelevant by now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2c_smbus_data union block member has a comment stating that an
extra byte is required for SMBus Block Process Call transactions. This
has been true for three weeks around June 2002, but no more since, so
it is about time that we drop this comment and fix the definition.
From: Hideki Iwamoto <h-iwamoto@kit.hi-ho.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/i2c.h | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Attached is kernel patch for UDP Fragmentation Offload (UFO) feature.
1. This patch incorporate the review comments by Jeff Garzik.
2. Renamed USO as UFO (UDP Fragmentation Offload)
3. udp sendfile support with UFO
This patches uses scatter-gather feature of skb to generate large UDP
datagram. Below is a "how-to" on changes required in network device
driver to use the UFO interface.
UDP Fragmentation Offload (UFO) Interface:
-------------------------------------------
UFO is a feature wherein the Linux kernel network stack will offload the
IP fragmentation functionality of large UDP datagram to hardware. This
will reduce the overhead of stack in fragmenting the large UDP datagram to
MTU sized packets
1) Drivers indicate their capability of UFO using
dev->features |= NETIF_F_UFO | NETIF_F_HW_CSUM | NETIF_F_SG
NETIF_F_HW_CSUM is required for UFO over ipv6.
2) UFO packet will be submitted for transmission using driver xmit routine.
UFO packet will have a non-zero value for
"skb_shinfo(skb)->ufo_size"
skb_shinfo(skb)->ufo_size will indicate the length of data part in each IP
fragment going out of the adapter after IP fragmentation by hardware.
skb->data will contain MAC/IP/UDP header and skb_shinfo(skb)->frags[]
contains the data payload. The skb->ip_summed will be set to CHECKSUM_HW
indicating that hardware has to do checksum calculation. Hardware should
compute the UDP checksum of complete datagram and also ip header checksum of
each fragmented IP packet.
For IPV6 the UFO provides the fragment identification-id in
skb_shinfo(skb)->ip6_frag_id. The adapter should use this ID for generating
IPv6 fragments.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (forwarded)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch moves rfcomm_crc_table[] into the RFCOMM core, because there
is no need to keep it in a separate file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows struct class_device to be nested, so that another
struct class_device can be the parent of a new one, instead of only
having the struct class be the parent. This will allow us to
(hopefully) fix up the input and video class subsystem mess.
But please people, don't go crazy and start making huge trees of class
devices, you should only need 2 levels deep to get everything to work
(remember to use a class_interface to get notification of a new class
device being added to the system.)
Oh, this also allows us to have the possibility of potentially, someday,
moving /sys/block into /sys/class. The main hindrance is that pesky
/dev numberspace issue...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A "coldplug + udevstart" can be simple like this:
for i in /sys/block/*/*/uevent; do echo 1 > $i; done
for i in /sys/class/*/*/uevent; do echo 1 > $i; done
for i in /sys/bus/*/devices/*/uevent; do echo 1 > $i; done
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: pass interface to class intreface methods
Pass interface as argument to add() and remove() class interface
methods. This way a subsystem can implement generic add/remove
handlers and then call interface-specific ones.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2O: cleanup - remove i2o_device_class
I2O devices reside on their own bus so there should be no reason
to also have i2c_device class that mirros i2o bus.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a refresh of an earlier patch to add "wakeup" support to the
PM core model. This provides per-device bus-neutral control of the
use of wakeup events.
* "struct device_pm_info" has two bits that are initialized as
part of setting up the enclosing struct device:
- "can_wakeup", reflecting hardware capabilities
- "may_wakeup", the policy setting (when CONFIG_PM)
* There's a writeable sysfs "wakeup" file, with one of two values:
- "enabled", when the policy is to allow wakeup
- "disabled", when the policy is not to allow it
- "" if the device can't currently issue wakeups
By default, wakeup is enabled on all devices that support it. If its
driver doesn't support it ... treat it as a bug. :)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Bellido Nicolas
The AAEC-2000 has an ARM PrimeCell PL110 Color LCD Controller.
This patch contains the platform glue that will be used by specific boards.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
This adds platform code for MTD devices on AAEC-2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
linux/config.h is not necessary in hardware.h, while asm/sizes.h and asm/arch//aaec2000.h will be used later.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
The AAED-2000 board has GPIO pins on an external port.
This patch adds the defines, and do the necessary mapping.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Add defines for GPIO registers on the AAEC-2000 processor.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
